TokeShimi B08LKG7D3Q LED Bathroom Mirror 55×36 Inch Instruction Manual
- June 17, 2024
- TokeShimi
Table of Contents
TokeShimi B08LKG7D3Q LED Bathroom Mirror 55×36 Inch
BEFORE INSTALLATION
Thank you for choosing TokeShimi products. To ensure the best possible experience, please read carefully and follow the instructions provided below before assembling and installing the product.
- Important Safety Instructions:
- Assemble the product by two or more adults to ensure proper installation.
- To connect the wires to the electrical junction box, consultation with a qualified technician or electrician is highly recommended.
- Disconnect power before installing, adding, or changing any components.
- Make sure that the fixing location can support the weight of the entire fixture (e.g. solid stone or brick walls).
- To prevent injury, the mirror must be installed according to the instructions provided.
- Pre-assembly:
- Inspect the product immediately upon receipt for any transit damage or missing parts.
- The voltage for your TokeShimi product should be between 100V and 120V. If the voltage exceeds 120V, please use a transformer.
- You can connect the wires directly to your junction box or plug
- Before Installation:
Please check and make sure that the mirror is functioning properly.
Anti-fog
The anti-fog function helps resist the troubling fog and keep a clear
reflection image. To save energy, it will automatically turn off after one
hour.
Color Temperature
You can select the color temperature by tapping the button: the first tap is
white light, the second tap is warm light, and the third one is natural light.
Touch Switch
The lighting mode will change as you tap the button: the first tap is for
front light and backlight, the second tap is for front light only, the third
one is for backlight only, and the light will be all off with a fourth tap.
The brightness can be adjusted with a long press on the button.
If no button is pressed within 15 seconds, the next tap will turn off the
light immediately.
Memory Function
The current setting of the mirror will be saved. When you turn on the
mirror next time, it will be in the same settings as it was.
CONTACT US
After opening the package, please inspect the product immediately and see if there is any damage or missing parts. If there is, please contact us by aftersales@tokeshimi-home.com or find us at Amazon by following steps:
- Open “Orders” at Amazon, find the product you have purchased and open the product page;
- Click Sold by “TokeShimi“, and click “Ask a question” on the redirected page;
- Click “An order I have placed“ in the chat with Seller Messaging Assistant ;
- Click in sequence “Your product“, ”Other”, “Troubleshooting“ from available options, you will see a message box after that.
Please leave us a message, and we will reply within 24 hours.
ACCESSORIES LIST
-
Bracket x 2
-
Screw x 6
-
Wall Anchor-A x 6
-
Wall Anchor-B x 6
TOOLS REQUIRED
-
Level
-
Marker
-
Hammer
-
Tape Measure
-
Electric Drill
-
Phillips Screwdriver
-
Safety Goggles
INSTALLATION INSTRUCTIONS
-
Decide whether to hang the mirror vertically or horizontally. Confirm the locations of drill holes with the positioning ruler provided in the package, and use a marker to mark the spots ①②③④ on the wall.
Vertical Installation
Horizontal Installation
Note: Please hang the mirror a few inches above the highest part of the faucet. -
Use an electric drill to punch holes at the marked spots, and then apply wall anchors with a hammer.
| Thickness of Wall | Recommended Drill Bit |
|---|---|
| ＞ 16mm | 1/4″ (6mm) drill bit, drilling depth in 1 31/32″ (50mm) |
8 ~ 16mm| 25/64″ (10mm) drill bit
＜ 8mm| Inapplicable
Note: Please wear goggles and pay attention to your safety while drilling.
-
Secure the two brackets to the wall with screws.
-
Connect the power by plugging into an outlet or hardwired to a standard circuit panel.
Plug-in
After hanging the mirror securely, plug the power cable to a standard socket.
Hardwired
Cut the head off the plug and hardwire it into an outlet.
Black wire — power supply L (LIVE)
White wire — power supply N (NEUTRAL)
Green wire — power supply E (EARTH)
WARNING: This mirror must be earthed.
REMINDER: Please make sure the power is cut off before installation. -
Place the mirror against the wall, align the hook with the mounted bracket, slowly lower the mirror down, and make sure that it slots into the right position and hangs securely.
SPECIFICATIONS
| PARAMETER | SPECIFICATION |
|---|---|
| Color Temperature | 3000-6000K |
| Input Voltage | AC100-120V |
| Output Voltage | 24V DC |
| CRI | ≥90 Ra |
| Working Temperature | -10~45℃ |
| Life Span | 25000 hours |
| Anti-fog | Yes |
| IP Rate | IP4 |
| Wiring Method | Hardwired / Plug in |
| Switch | Touch Sensor Switch |
HOW TO USE AND CLEAN
In order to keep the LED mirror in perfect condition, we suggest a proper use and regular cleaning.
How to Use
- Please ensure that the product is used within the safe voltage range of 100V-120V.
- Please wrap electrical tape around the wires to prevent electrical leakage.
- Avoid using hard or pointed items to strike the mirror glass so as to prevent damage.
How to Clean
When cleaning the mirror, please follow these steps:
- Use a soft, non-abrasive cloth to clean the mirror. Avoid using rough or abrasive materials that may damage the surface.
- Do not use any cleaning agents that may cause irritation or damage to the mirror’s finish. Instead, use any of the recommended cleansers to remove dirt and grime:
Gentle liquid detergents
Colorless cleansers
Warranty
A two-year warranty from the date of your purchase.
CUSTOMERS SUPPORT
If you have any questions, please feel free to contact us via
aftersales@tokeshimi-home.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>