BROWIN 343218 Classic Convex Still 2 Clarifiers User Manual
- May 15, 2024
- BROWIN
Table of Contents
BROWIN 343218 Classic Convex Still 2 Clarifiers
Product Information
Specifications:
- Capacity: 18 L
- Includes: 2 clarifiers
- Material: Stainless steel
- Dimensions:
- Height: 66 cm
- Diameter of the container: 31 cm
Product Usage Instructions
Assembly Instructions:
- Thoroughly wash the container with dishwashing liquid before first use. Do not use wire scourers or cleaning powders.
- Fix the condenser to the lid using the gasket and bolt provided.
- Apply PTFE tape to the threads of the clarifiers and screw on the ball valves, ensuring they are closed.
- Place the container on the heating spot and pour in liquid (25%-90% capacity). Mount the lid with the condenser and engage the clamps.
- Secure the electronic thermometers – one at the lid and the other on the stub pipe of the condenser.
- Place the thermometer probes in their respective openings on the container and condenser.
Cleaning Instructions:
To clean stainless steel parts, avoid using abrasive materials to prevent
accelerated corrosion.
Additional Products:
Complementary products available for purchase separately include an
alcoholometer for measuring distillate strength and a distillation parrot.
FAQ
-
Q: What should be the filling level of the container?
A: The recommended filling level is between 25% and 90% of the container’s capacity. -
Q: Can this still be used on different heat sources?
A: Yes, this kit is suitable for use on various heat sources.
This manual constitutes a part of the product and should be stored in a manner
that enables consulting its content in the future. It includes important
information about the product and its use.
PLEASE NOTE! The device can be used by adults only. Never leave a working
device unattended. Make sure that the device storage location is properly
secured against the access of children and unauthorized persons.
The manufacturer is not liable for any presumptive damage caused by the
application of the device in a way inconsistent with its intended use or by
incorrect operation of the device.
The manufacturer reserves the right to modify the product at any moment,
without prior notice, to adjust it to provisions of the law, standards, or
directives, or due to structural, commercial, aesthetic, or other reasons.
PLEASE NOTE! Each country has its legal regulations regarding the
principles of ethyl alcohol, wine products, and spirit drinks and placing them
on the market, as well as sanctions for not complying with these regulations.
- The rules of production of alcohol on the territory of the Republic of Poland are regulated by the following acts: the act of 2nd of March 2001 on production and bottling of wine products, trading these products, and organization of the wine market, and the act of 18th of October 2006 on the production of spirit drinks, their registration, and protection of geographical indications of spirit drinks. BROWIN Sp. z o. o. Sp. k. company is not liable for its products being used in a way that does not comply with binding provisions of the law.
- The 18 classic Convex still is a professional, modular still with an 18 L container, two clarifiers, and a condenser complete set made of high-quality stainless steel (INOX), intended for use on all types of cooktops.
The product is distinguished by the following features, among others:
- High quality – made of stainless steel and durable plastic components, airtight featuring precision connections, and characterized by operational efficiency and durability.
- Can be used on various heat sources – on an electric, induction, ceramic, gas or coil cooktop.
- Two electronic thermometers were included – providing precise temperature measurements during the distillation process.
- High efficiency – the 18 L container makes it possible to distill a large volume of liquid (however, it is recommended not to exceed 90% of the capacity).
- Complete set – the kit includes an 18 L container with a convex lid, a condenser with two clarifiers, two electronic thermometers with batteries included, valves for clarifiers, two hoses, a water supply connector, assembly elements, and a user manual.
- Expandable kit – the container and lid are compatible with other distillation modules available from BROWIN.
The still is equipped with an 18 L container (with a recommended filling level of up to 90% of capacity and not less than 25%), and a condenser with 2 clarifiers and 2 thermometers, allowing distillation to be carried out without any additional equipment. This kit is suitable for use on various heat sources. Two precision thermometers with probes facilitate temperature control – inside the container and in the clarifier. Plasticized PVC hose with coupling enables quick connection of water supply and drainage. The silicone hose is used for collecting the distillate.
The kit features an airtight container of convex-type
with a dome-like lid that allows for potential foaming of the batch or mash,
without the risk of contamination of the column and its filling. The dome
shape, inspired by classic ‘swan-neck’ alembics, increases the stability of
the entire column, even with a tall still, which also translates into
increased stability of the entire distillation process. The dome lid has only
a main hole for mounting the column.
- Distilling has never been so easy! Our abundant experience, our drive to look for novel and improved solutions, and our focus on high quality all allow us to offer proven specialist equipment for distilling.
- The container and lid are fully compatible with the distillation modules available from BROWIN – when you have this still, you can upgrade it with components such as connectors, refluxes, inspection glasses, condensers or even side receivers.
ASSEMBLY INSTRUCTIONS
Please note: (Before being used for the first time the container should be
washed thoroughly with a dishwashing liquid and dried.
Do not use wire scourers or cleaning powders.
-
The condenser should be fixed to the lid (using its middle opening) by placing the gasket on the bottom of the lid and tightening it with a bolt so that the condenser is stable.
-
Pull the PTFE tape (included in the kit) over the threads of the clarifiers and screw the ball valves onto them. After screwing them on, make sure they are closed.
-
Place the container on the heating spot and then pour in liquid in an amount not less than 25% of the container’s capacity and not more than 90% of it. Mount the lid with the condenser and engage the clamps.
-
Place electronic thermometers in frames and fix them – one at the lid and the other on the stub pipe of the condenser from which the distillate flows.
To ensure that the frame on the stub pipe remains in a stable position, cut off approx. 1 cm of the PTFE hose and press it onto the slid frame from below. Next, a silicone hose should be fitted onto the stub pipe to receive the distillate. -
Cut the plasticized PVC hose in such a manner that its length corresponds to the distance of the set from the water connection and drain. Remember that the plasticized PVC hose is to be used for water supply and drainage, while the silicone hose is intended for distillation. Connect the hoses with the condenser stub pipes – the cooling water feeding hose to the lower stub pipe and the cooling water draining hose to the upper one.
-
Place the probe of the thermometer mounted at the lid in the opening in the wall of the container, and the probe of the thermometer next to the condenser in the opening at the top of the clarifier.
KIT ELEMENTS:
- 18 L container with a dome lid
- Head – a classic condenser with two clarifiers
- Plasticized PVC hose with quick coupling for connecting water supply
- Silicone hose for collecting the distillate
- 2 clarifier valves
- 2 frame-mounted electronic thermometers with probe
- Accessories
- User manual
Container
- 18 L container with an opening for the thermometer probe
- (convex) dome lid with a silicone gasket and an opening for column installation
- 2 handles for moving around
- 5 clamping brackets
- material: stainless steel
- heat sources: an electric, induction, ceramic, or gas cooker, or a heating coil
- recommended filling: not more than 90% and not less than 25% of the container volume
Distillation unit
- a condenser with two clarifiers, made of stainless steel, screwed to the container
- two 1/8” ball vales
- plasticised PVC hose: 2 m
- silicone hose 15 cm
- PTFE tape for installing valves
Electronic thermometers
- a thermometer for reading the approximate temperature inside the container
- thermometer for measuring the temperature of vapors inside the clarifier
- 2 thermometer frames
- 2 stainless steel probes with a 100 cm long cable
- temperature range: from -50oC to +110oC Tolerance: +/-1oC
- precision: 0.1oC
- batteries for thermometers: 2 x LR44 (included)
Kit dimensions:
- height: 66 cm
- container diameter: 31 cm
Complementary products available in the Browin’s product range, to be purchased separately:
- alcoholmeter for measuring the alcohol content in the distillate
- proofing parrot
CLEANING AND MAINTENANCE
Please note:
The container is made of AISI 201 steel which requires maintenance and
drying after each use. Lack of adherence to the recommendations of the
manufacturer may result in damage to the product such as the appearance of
rust, pitting or discolorations.
Stainless steel is resistant to corrosion thanks to the fact that the alloy
elements form a thin, transparent protective layer on its surface. It is
extremely thin but provides excellent protection of the steel surface against
corrosion. If it is damaged mechanically and not maintained properly, pitting
may appear on it. The frequency of cleaning and maintenance depends on how
frequently a given steel material is used and the conditions in which it is
used. In case of outdoor use, where it can be expected that rain and snow will
wash away the stains accumulated, discolorations may appear. In such case, it
is necessary to remove all the stains. Every stainless steel element the
surface of which is damaged will rust if it is not secured.
When cleaning stainless steel:
- never use strongly abrasive materials or steel wool.
- never use inorganic acids (especially hydrochloric acid) or bleaches containing sodium hypochlorite for cleaning, as they may cause surface discolorations and corrosion pitting corrosion;
- never let stainless steel come in contact with non-alloy steel (the particles of such steel types will undergo accelerated corrosion on the stainless steel surface).
We recommend the following to take good care of the product:
- Solid dirt and contaminations should be rinsed with clean water, followed by wiping the surfaces with a soft cloth.
- For more severe staining – mild soap or detergent (cleaning ammonia, baking soda, vinegar, citric acid) and a soft nylon brush.
- Rinse well after cleaning.
- Clean the elements at least once a year.
Stainless steel maintenance:
- Mild rus t: Home cleaning agents dedicated to stainless steel, containing calcium carbonate or citric acid. Rinse well with water.
- Moderate discolorations: Clean with agents based on phosphoric acid or 10% solution of phosphoric acid. Spray the surface and wait for 30-60 minutes (according to the producer’s recommendations). After cleaning, neutralise the acid with diluted ammonia or mild alkaline detergent. Rinse well with water.
- Severe rust : Use professional service providers or dedicated products for steel etching and passivation. Always rinse the surface with water after processing. Please adhere to the recommendations specified in the detergent user manual.
- Nicks and scratches on ground or brushed surface: Remove using a polishing wheel by polishing in the direction of the surface structure (use a non-iron polishing material), then wash with a mild scouring detergent. Rinse with clean cold water and then wipe clean.
- Stains from oil, fat, and grease – remove with organic solvents and then with warm water with soap or mild detergent. Rinse with clean cold water and then wipe clean.
When using the methods specified above, always adhere to OHS principles.
- Use phosphoric and oxalic acid or etching paste only if other methods prove to be unsuccessful.
- Wear rubber gloves and protective eyewear and adhere to safety regulations regarding works of this type.
- Ensure good ventilation when using solvents and pay attention to fire hazards.