cecotec POWER ESPRESSO 20 STEEL PRO Coffee Machine User Manual

cecotec POWER ESPRESSO 20 STEEL PRO Coffee Machine

Specifications:

• Product Name: Power Espresso 20 Steel Pro
• Model: 01984_PoweEspresso 20 Steel Pro RP_01230710
• Material: Stainless Steel
• Power: 20W
• Capacity: 1.5L

Product Information:
The Power Espresso 20 Steel Pro is a high-quality espresso machine designed for home use. It features a durable stainless steel construction and a powerful 20W motor for brewing delicious espresso drinks.

Product Usage Instructions

Parts and Components:
Before using the espresso machine, familiarize yourself with its different parts and components. Ensure all parts are clean and in good condition.

Before Use:
Fill the water tank with fresh, cold water and ensure it is securely in place. Insert the coffee grounds into the portafilter and tamp them down evenly. Place the portafilter into the group head and lock it in position.

Operation:
Turn on the machine and allow it to heat up. Once ready, place your cup under the portafilter and start the brewing process. Monitor the extraction time to ensure you get the perfect shot of espresso.

Cleaning and Maintenance:
After each use, clean the portafilter, group head, and steam wand thoroughly. Regularly descale the machine to prevent mineral buildup. Refer to the user manual for detailed cleaning instructions.

Troubleshooting:
If you encounter any issues with the espresso machine, refer to the troubleshooting section of the user manual. Common problems include low pressure, leaking water, or inconsistent espresso extraction.

FAQ:

Q: How do I descale the espresso machine?
A: To descale the machine, mix a descaling solution with water according to the manufacturer’s instructions and run it through the machine’s brewing cycle. Then, rinse the machine thoroughly with clean water.

Q: Can I use pre-ground coffee with this espresso machine?
A: Yes, you can use pre-ground coffee with the Power Espresso 20 Steel Pro. Make sure to adjust the grind size and amount of coffee accordingly for best results.

SAFETY INSTRUCTIONS

Read these instructions thoroughly before using the device. Keep this instruction manual for future reference or new users.

• All safety instructions must be closely followed when using the appliance.
• This symbol means “Caution, Hot Surface”. Accessible surfaces are likely to heat up during use. Be careful not to burn yourself.
• This device is designed for domestic use only and is not intended for bars, restaurants, farmhouses, hotels, motels,
• The appliance must not be used by children. Keep this appliance and its power cord out of their reach.
• This appliance can be used by persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
• Children must not play with the appliance. Cleaning and user maintenance should not be carried out by unsupervised children.
• WARNING: the filling opening or the water tank must not be opened during operation.
• WARNING: take precautions to avoid spillage of liquids on the cable.
• WARNING: incorrect or improper use can be dangerous for the user and damage the appliance. Use the appliance only for the purposes described in this manual. The surface of the heating element is subject to residual heat after use.
• Ensure that the mains voltage matches the voltage specified on the appliance rating label and that the plug is earthed.
• Do not immerse the cable, plug, or any other non-removable part of the device in water or any other liquid or expose electrical connections to water. Make sure your hands are dry before handling the plug or switching on the device.
• Warning: if the device falls accidentally in water, unplug it immediately. Do not touch the water!
• Check the power cable regularly for visible damage. If Technical Support Service of Cecotec
• in order to avoid any type of danger.
• WARNING: Do not use the appliance if its cable, plug, or housing are damaged, nor after it malfunctions or has been dropped or damaged in any way.
• Do not twist, bend, pull, or damage the power cable. Protect it from sharp edges and heat sources. Do not allow the cable to touch hot surfaces. Do not let the cable hang over the edge of the working surface or worktop.
• This appliance is not intended to be operated by means of an external timer or separate remote-control system. when not in use and before cleaning it. Pull from the plug, not the cable, to disconnect it from the outlet.
• Supervise children to prevent them from playing with the appliance. Close supervision is necessary when the appliance is being used by or near children.
• Place the appliance on a dry, stable, flat, heat-resistant surface.
• Do not use the appliance under the following circumstances:
• On or near a gas or electric hob, in heated ovens, or near open flames.
• On soft surfaces (such as carpets) or where it may tip over during use.
• Outdoors or in areas with high humidity levels.
• Do not cover the appliance during operation.
• Never leave the device unattended during use. Unplug it from the mains supply when you finish using it or when you leave the room.
• Do not try to repair the device by yourself. Contact the
• Cleaning and maintenance must be carried out according to this instruction manual to make sure the appliance before moving and cleaning it.
• Do not wash the appliance in dishwashers.
• No liability is accepted for any eventual damage or personal injuries derived from misuse or non-compliance with this instruction manual.

PARTS AND COMPONENTS

Fig. 1

1. Power button

2. Single espresso button

3. Double espresso button

4. Steam button

5. Metal grille

6. Drip tray

7. Inner drip tray

8. 1 cup filter

9. 2 cups filter

10. Filter holder

11. Water tank cover

12. Water tank

13. Steam regulator knob

14. Steamer

15. Steamer handle

16. Steam outlet

17. Pressing powder spoon

Control panel

Figure 2

• A. Pressure gauge
• B. Power button
• C. Single cup button
• D. Double cup button
• E. Steam button

NOTE: the graphics in this manual are schematic representations and may not exactly match the device.

BEFORE USE

• This appliance is packaged in a way as to protect it during transport. Take the device out of its box and remove all packaging materials. You can keep the original box and other packaging elements in a safe place. This will help you prevent damage to the device when transporting it in the future. In case the original packaging is disposed of, make sure all packaging materials are recycled accordingly.
• Make sure all parts and components are included and in good conditions. If there is any immediately.
• Wash the water tank with its cover, the pressing powder spoon and filter as well as the filter holder with lukewarm water and a little neutral dishwashing detergent. After that, rinse with clean water and dry.
• Also, clean the housing of the espresso machine and the drip tray with its grille with a soft, damp cloth and dry all parts.

Box content

• Power Espresso 20 Steel Pro espresso machine
• Filter holder
• 1 cup filter
• 2 cups filter
• Coffee spoon
• Instruction manual

OPERATION

1. Fill the water tank with cold water up to the MAX mark on the deposit.

2. Connect the plug to a socket that has a suitable voltage.

3. Press the power button. Next, the indicator light will turn on and the espresso machine will automatically start to preheat. Once the preheating process is completed, all buttons will light up steadily. The preheating process takes about 2 minutes.

4. Put a cup under the steamer. Turn the steam regulator knob. Let hot water run out of the This process allows the water to pass through to the pump the first time it is used.
   ATTENTION: the first time you use the espresso machine it may make a loud noise or vibrate. This is normal for a 20 bar pressure pump. When you use it again, it will make less noise.

5. Put the filter in the filter holder.
   ATTENTION: you may find it a little difficult to remove the filter from the filter holder when you want to change it. You can use another filter for leverage.

6. Insert the filter holder without ground coffee into the upper part of the espresso machine by making a 45° movement to the left and turn it back to the right until it clicks into position. The filter holder must be perpendicular to the machine or slightly inclined to the right.

7. Put an empty cup under the filter holder and press the single or double cup button to start preparing coffee.

8. Once the preparation process is complete, empty the water from the tank. The espresso machine is now ready for use.

Coffee brewing

1. Remove the filter holder and fill the filter with ground coffee using the pressing powder spoon supplied with the espresso machine.
   RECOMMENDATION: 7-9 g for a single cup and 13-15 g for a double cup. The amount may vary depending on your preferences and the type of coffee you have used

2. Compress the coffee with the pressing powder spoon. The ground coffee must be pressed evenly to obtain a well levelled and smooth surface. Clean any coffee residue from the edge of the filter holder.

3. Insert the filter holder into the upper part of the espresso machine by making a 45° movement to the left and turn it back to the right until it clicks into position. The filter holder must be perpendicular to the machine or slightly inclined to the right.

Preparing espresso coffee

1. Make sure the steam regulator knob is in the Off position.
2. Place the preheated cup(s) under the filter holder.
3. Press the single or double cup button to set the desired amount.

The taste of the coffee will depend on different factors, such as the type of coffee bean, the degree of roast, the freshness, the coarseness or fineness of the grind, the amount of ground coffee and the tamping pressure. Try adjusting these factors one at a time until you get the taste you want.

Frothing milk
To prepare a classic cappuccino or latte, we recommend:

• using fresh, cold whole milk. The density of the frothed milk will depend on the percentage of milk fat.
• using stainless steel milk jugs, circular, rounded, narrower at the top, with a spout, to decorate the cappuccino with the froth.

Before starting, it is important to move the steamer slightly outwards to place the jug directly underneath it to facilitate the movements necessary to froth the milk properly.

Then follow the next steps:

1. Press the steam button. The steam button will start flashing if the temperature is not high enough to produce steam. Once the preheating process is completed, the steam button will turn on.

2. Turn the steam regulator knob slightly counterclockwise to remove any condensation on the steamer, then turn the knob back to turn it off.

3. Place the jug, half-filled with cold milk, under the steamer.

4. Place the steam nozzle just below the surface of the milk. If it is inserted too deep, the milk will not froth; if it is not inserted deep enough, the milk will start to bubble, and the froth will disappear. It is important that the steamer is not in the centre, but close to the edge of the jug, which is slightly inclined.

5. Turn the knob to the ON position. Steam will come out of the steamer.
   ATTENTION: the whole process should not take more than 3 minutes, as the machine will automatically stop dispensing steam after 3 minutes of continuous steaming.
   ATTENTION: to froth milk properly, the steam nozzle must always be in contact with the milk and not with the foam. Therefore, as the foam layer increases, lift the jug slightly, trying to keep the steamer in contact with the milk, without touching the bottom of the jug.

6. Once the desired foam is obtained, it is necessary to push the steam nozzle deeper in order to heat the milk thoroughly.
   ATTENTION: it is advisable to always keep one hand on the rounded part of the jug so that you can feel the temperature of the milk rise without frothing.

7. Once the desired result is achieved, turn the steam regulator knob to the “OFF” position to stop dispensing steam and remove the jug.
   ATTENTION: to make the foam more compact, it is advisable to tap the jug on a flat surface after foaming.

8. Then, press the steam button again to stop the steam outlet. Pour the frothed milk into the previously brewed espresso.
   WARNING: the steamer may be very hot during and after use. To avoid burns, move it only by resting your fingers on the rubber handle on the steamer.

9. Turn the steam regulator knob to remove any milk residue from the pipe and then turn the steam knob off again.

10. Do not prepare the coffee immediately after frothing the milk. The temperature of the heater is too high and the machine is protected against overheating. Under this protection, the single and double coffee buttons will flash if you press either of them.

Allow the warmer to cool down first; otherwise, the coffee may burn and come out of the filter holder. Please, follow the next 4 steps to cool down the machine.

• Turn the steam regulator knob to the ON position so that hot water comes out.
• Allow hot water to come out of the steamer to cool down the heater.
• Once the heater cools down, all buttons will light up.
• Return the knob to the OFF position. The machine is ready for the next preparation now.

Hot water preparation

1. Switch on the machine and wait for all the buttons to light up.
2. Put a cup under the steamer.
3. Turn the knob to the ON position. Hot water will flow out of the steamer.
4. Once the desired amount of hot water has been dispensed, turn the steam regulator knob to the OFF position.

ATTENTION:

• the whole process should not take more than 40 seconds, as the machine will automatically stop dispensing hot water after 40 seconds of continuous operation. If you want more hot water, start the cycle again.
• the steamer may be very hot during and after use. To avoid burns, move it only by resting your fingers on the rubber handle on the steamer.

Pressure gauge for espresso coffee
The needle of the pressure gauge indicates the extraction pressure.

Ideal pressure zone for espresso
When it is positioned anywhere in the espresso zone during extraction, it means that the espresso has been extracted at the ideal pressure.

Low-pressure zone

• When the pressure gauge needle is below the espresso range during extraction, this indicates that the espresso has been extracted with insufficient pressure.
• This can occur when water passes through the ground coffee too quickly, resulting in espresso that is under-extracted, watery, earthy, and lacking in crema and flavour.
• Possible causes of insufficient extraction include too coarse grind, insufficient coffee in the filter, insufficient tamping, or a combination of all these factors.

High-pressure zone

• When the pressure gauge needle is above the espresso range during extraction, this indicates that the espresso has been extracted with too much pressure.
• This can occur when the water passes through the ground coffee too slowly, resulting in an over-extracted, very dark, and bitter espresso with a mottled and uneven crema.
• Possible causes of over-extraction are too fine grind, too much ground coffee in the filter,excessive tamping, or a combination of all of these.

How to adjust the single and double dosing level

Adjust the individual dosage amount

1. Press and hold the single cup button for 3 seconds. The machine will beep 3 times briefly and start brewing.
2. Press the single espresso button again when you have drawn off the desired amount of espresso. The machine will beep 3 times slowly to indicate that the new individual cup quantity has been set.

Adjust the double dosage amount

1. Press and hold the double cup button for 3 seconds. The machine will beep 3 times briefly and start brewing.
2. Press the double espresso button again when you have drawn off the desired amount of espresso. The machine will beep 3 times slowly to indicate that the new double cup quantity has been set.

ATTENTION: the brewing time varies between 8 and 60 seconds. If not, it means that the adjustment has not worked.

Reset the default amount
To reset the default single and double dosing amount, press and hold both buttons for 5 seconds. The machine will beep 3 times and all buttons will flash 5 times. The machine will return to its original default settings.

Warning for lack of water
For low water warning, the different buttons will flash green simultaneously. Once the water shortage warning is activated, proceed as follows:

1. Refill the water tank with water at room temperature.
2. Place an empty cup under the brewing head and point the milk spout into the cup.
3. Press one of the buttons. The machine will start dispensing hot water.
4. Once the hot water has finished flowing out, it means that the internal pipes of the coffee machine are full and clean. The buttons will light up again and the machine will be ready for use again.

WARNING: never press any of the buttons after the low water warning has been triggered without refilling the water tank.

Standby mode
The machine will enter standby mode after 15 minutes of non-use. All buttons will turn off. In case you want to use it again, press the power button and proceed as desired.

CLEANING AND MAINTENANCE

Regular cleaning and maintenance guarantee that the coffee machine works properly and ensure that the coffee taste is optimal, that there is a constant flow of coffee and that the milk froth is excellent for a long time.
Cleaning the filter holder and filters

Keep the filter holder and filters clean to ensure optimal results.

WARNING: to avoid burns, remove the filter only when the filter holder has cooled down completely.

1. Remove the filter from the holder and wash it with warm water.
2. If you notice any faults when brewing coffee, immerse the filter in boiling water for 10 minutes and then rinse it with tap water.

Cleaning the steamer

1. Immediately after frothing the milk, turn the steam regulator knob to remove any milk residue from the steamer.
2. Clean the steamer with a damp cloth. To clean it more thoroughly, you can unscrew the steamer and wash it with tap water.
3. If the steam nozzle orifice becomes clogged, make sure that the steam regulator knob is in standby mode. To switch off the machine, press the power button. Use a pin to unclog the hole.

Cleaning of the head where the filter holder is placed
Regularly remove ground coffee residue from the coffee head with a brush and wash it with hot water following the steps below.

1. Insert the filter holder into the machine upper part without ground coffee.
2. Place an empty cup under the brewer head.
3. Press the double cup button and fill the cup with water.
4. Remove the filter holder from the brewer head and clean it with a dry cloth.

WARNING: do not attempt to disassemble the brewer head. It will damage the head and may cause leakage.

Descaling
To ensure that your coffee machine works properly and that the taste of your coffee is preserved, it is necessary to descale, clean and check the machine periodically.
In addition, after 500 times of preparation cycle, a descaling warning will appear. The power button will flash 5 times to indicate that the machine needs to be descaled. The descaling warning will appear every time you switch on the machine if you do not run the cycle.

Please, follow the next 4 steps to descale the machine.

1. Fill the water tank with coffee machine descaler (4 parts water to 1-part descaler) up to the MAX mark.
   ATTENTION: please also refer to the instructions of the descaler product. Use a commercial household descaler, or use citric acid instead. In this case, use 100 parts of water to three parts of citric acid.

2. Place a cup or any other suitable container on the metal tray and press and hold the double cup button and the steam button at the same time for 5 seconds. The machine will start the descaling process, which will last 7 minutes and stop automatically.

3. Repeat the above steps until all the water with the descaling product is used up.

4. Then, repeat the process two more times using only CLEAN TAP WATER without descaler.

CAUTION: the parts of the espresso machine and accessories are not dishwasher safe.

TROUBLESHOOTING

There is no water

| Water tank is out of water.| Add an adequate amount of water to the tank.
The water tank is out of place.| Replace it again.
If there is still no water after 120s of operation or the water tank is empty, the machine has been idle for too long.| Remove the water tank, add 5 ml of water in the inlet, replace the tank and use the hot water function once.

No steam

| The steam outlet is blocked.| Insert a pin into the steam outlet.
No water in tank.| Add an adequate amount of water to the tank.
The water tank is out of place.| Replace it again.
Less steam| If you press the steam button and do not let the preheating process finish.| Press the steam button and wait until the indicator light changes from flashing to steady on.
---|---|---
If the steam function starts when the machine is cold.| Activate the double- cup brewing function or wait for the preheating to finish in steam mode before frothing the milk.
Turn the steam regulator knob to the maximum position.| Slowly turn the steam knob until steam comes out when frothing the milk. Adjust the amount of steam slowly after a few seconds, according to your preference.
Low milk froth| No whole milk is used.| Use whole milk.
If cold milk is not used.| Place the milk in the refrigerator at 2-5 ºC.
The steam nozzle is too deep in the milk.| Immerse the steam nozzle into the surface of the milk to a depth of 1 cm.
Less fat| coarse.|
compact enough.| Tamp it down with adequate pressure.
frothing the milk.| Make sure that the machine is completely cool before use.
Too much funnel|

frothing the milk.

| Make sure that the machine is completely cool before use.
edge of the funnel after filling it

| funnel with a brush or by hand.

a long time to brew or comes out in small quantities

|

| too coarse or too fine, it should be of standard quality and quantity (1
---|---|---
 | not be too fine.
The water heater has no water.| Before preheating, press the single cup / hand control button, let about 180 ml of water flow out of the steamer.
Single or double

is clogged machine

| The edge of the filter is too tight.| Insert the funnel into the brewer and turn it left and right until the filter comes out or use the funnel to push the filter down. Check if the edge of the filter

is coming out each time the funnel is

inserted.

cold| the low-temperature mode.| temperature mode.

If you press the manual control

the preheating process is finished.

| Press the manual control button after the preheating process is completed.
If you press the manual control

the preheating process is finished.

| Use the double brew function (do not put

Drain the water from the heater before preheating.| Before the preheating process, press the single cup / manual control button and let about 180 ml of water flow out of the steamer.

TECHNICAL SPECIFICATIONS

• Product reference: 01984
• Product: Power Espresso 20 Steel Pro Espresso Machine
• Voltage: 220-240 V
• Frequency: 50-60 Hz
• Power: 1350 W

Technical specifications may change without prior notification to improve product quality.
Made in China | Designed in Spain

DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC APPLIANCES
This symbol indicates that, according to the applicable regulations, the product and/or batteries must be disposed of separately from household waste. When this product reaches the end of its shelf life, you should dispose of the cells/batteries/accumulators and take them to a collection point designated by the local authorities.

Consumers must contact their local authorities or retailer for information concerning the correct disposal of old appliances and/or their batteries.
Compliance with the above guidelines will help protecting the environment.

TECHNICAL SUPPORT AND WARRANTY

Cecotec shall be liable to the end user or consumer for any lack of conformity that exists at the time of delivery of the product under the terms, conditions, and deadlines established by the applicable regulations.
It is recommended that repairs be carried out by qualified personnel.
If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact the official Cecotec Technical Support Service at +34 963 210 728.

COPYRIGHT

The intellectual property rights over the texts in this manual belong to CECOTEC INNOVACIONES, S.L. All rights reserved. The contents of this publication may not, in whole or in part, be reproduced, stored in a retrieval system, transmitted, or distributed by any means (electronic, mechanical, photocopying, recording or similar) without the prior authorization of CECOTEC INNOVACIONES, S.L.

www.cecotec.es

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>