ALPINE CDE-9850Ri WMA CD Receiver Owner’s Manual
- June 13, 2024
- Alpine
Table of Contents
ALPINE CDE-9850Ri WMA CD Receiver
Product Information
- Product Name: RDS MP3/WMA CD Receiver
- Model: CDE-9850Ri
- Manufacturer: Alpine Electronics
- Country of Origin: Japan
- Manufacturer Contact Information:
- ALPINE ELECTRONICS MARKETING, INC. (Japan) – Phone: 03-5496-8231
- ALPINE ELECTRONICS OF AMERICA, INC. (USA) – Phone: 1-800-ALPINE-1 (1-800-257-4631)
- ALPINE ELECTRONICS OF CANADA, INC. (Canada) – Phone: 1-800-ALPINE-1 (1-800-257-4631)
- Dalian Dongtai Colour Printing Technology Co., Ltd. (China)
- ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD. (Australia) – Phone: 03-8787-1200
- ALPINE ELECTRONICS GmbH (Germany)
- ALPINE ELECTRONICS OF U.K. LTD. (United Kingdom) – Phone: 0870-33 33 763
- ALPINE ELECTRONICS FRANCE S.A.R.L. (France) – Phone: 01-48638989
- ALPINE ITALIA S.p.A. (Italy) – Phone: 02-484781
- ALPINE ELECTRONICS (Spain) – Phone: 945-283588
- ALPINE ELECTRONICS (BENELUX) GmbH (Belgium) – Phone: 02-725-13
Product Usage Instructions
Turning Power On and Off:
To turn on the CD Receiver, press the Power button. – To turn off the CD
Receiver, press and hold the Power button until the unit powers off.
Detaching and Attaching the Front Panel:
To detach the front panel, press the Release button located on the lower-left
side of the panel. Gently pull the panel towards you to remove it.
To attach the front panel, align the panel’s guide pins with the slots on the
main unit and firmly push it in until it clicks into place.
Initial System Start-Up:
After turning on the CD Receiver, it will go through a start-up sequence.
During this time, avoid pressing any buttons or removing the front panel.
Adjusting Volume:
To increase the volume, turn the Volume knob clockwise. To decrease the
volume, turn the Volume knob counterclockwise.
Adjusting Sound Settings:
- Bass/Treble/Balance/Fader: Use the corresponding buttons or knobs to adjust these settings according to your preference.
- Defeat: Press the Defeat button to deactivate all sound adjustments temporarily.
Displaying Text:
The CD Receiver can display text information. Refer to the user manual for
detailed instructions on how to access and view text on the display.
Listening to Radio:
Press the Source button repeatedly until “Tuner” is displayed.
Use the Seek/Track buttons to tune into a radio station manually or
automatically.
Use the Preset buttons to store and recall your favorite radio stations.
Setting RDS Reception Mode and Receiving RDS Stations:
RDS (Radio Data System) allows for additional information to be displayed on
compatible radio stations.
Use the RDS buttons or knobs to set the reception mode and access RDS
features. Refer to the user manual for detailed instructions.
Note: For more detailed instructions and information on other functions,
please refer to the complete user manual provided with the product or visit
the official website at https://manual-hub.com/.
FOR CAR USE ONLY/NUR FÜR AUTOMOBIL GEBRAUCH/POUR APPLICATION AUTOMOBILE
UNIQUEMENT/ PARA USO EN AUTOMÓVILES/SOLO PER L’UTILIZZO IN AUTOMOBILE/ENDAST
FÖR BILBRUK
R
EN
RDS MP3/WMA CD Receiver
CDE-9850Ri
DE
· OWNER’S MANUAL
Please read before using this equipment.
FR
· BEDIENUNGSANLEITUNG
Lesen Sie diese Bedienungsanleitung bitte vor
Gebrauch des Gerätes.
· MODE D’EMPLOI Veuillez lire avant d’utiliser cet appareil.
· MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo.
ES
· ISTRUZIONI PER L’USO Si prega di leggere prima di utilizzare il
attrezzatura.
· ANVÄNDARHANDLEDNING Innan du använder utrustningen bör du läsa igenom denna användarhandledning.
ALPINE ELECTRONICS MARKETING, INC. 1-1-8 Nishi Gotanda, Shinagawa-ku,
Tokyo 141-0031, Japan Phone 03-5496-8231
ALPINE ELECTRONICS OF AMERICA, INC. 19145 Gramercy Place, Torrance, California
90501, U.S.A.
Phone 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS OF CANADA, INC. 777 Supertest Road, Toronto, Ontario M3J
2M9, Canada
Phone 1-800-ALPINE-1 (1-800-257-4631)
Dalian Dongtai Colour Printing Technology Co., Ltd. No.24 Liaohexisan Road,
Dalian Economic&Technical Development Zone, China
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD. 161-165 Princes Highway, Hallam
Victoria 3803, Australia Phone 03-8787-1200
ALPINE ELECTRONICS GmbH Frankfurter Ring 117,
80807 München, Germany Phone 089-32 42 640
ALPINE ELECTRONICS OF U.K. LTD. Alpine House
Fletchamstead Highway, Coventry CV4 9TW, U.K. Phone 0870-33 33 763
ALPINE ELECTRONICS FRANCE S.A.R.L. (RCS PONTOISE B 338 101 280)
98, Rue de la Belle Etoile, Z.I. Paris Nord Il, B.P. 50016, 95945 Roissy
Charles de Gaulle
Cedex, France Phone 01-48638989
ALPINE ITALIA S.p.A. Viale C. Colombo 8, 20090 Trezzano
Sul Naviglio (MI), Italy Phone 02-484781
ALPINE ELECTRONICS DE ESPAÑA, S.A. Portal de Gamarra 36, Pabellón, 32
01013 Vitoria (Alava)-APDO 133, Spain Phone 945-283588
ALPINE ELECTRONICS (BENELUX) GmbH Leuvensesteenweg 510-B6, 1930 Zaventem,
Belgium Phone 02-725-13 15
IT SE
Designed by ALPINE Japan Printed in China (Y) 68-04123Z56-A
Operating Instructions
WARNING
This symbol means important instructions. Failure to heed them can result in
serious injury or death.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING
YOUR VEHICLE.
Any function that requires your prolonged attention should only be performed
after coming to a complete stop. Always stop the vehicle in a safe location
before performing these functions. Failure to do so may result in an accident.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISE WHILE
DRIVING.
Failure to do so may result in an accident.
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric shock.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may result in
fire, etc.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed, consult a
physician immediately.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES.
Failure to do so may result in fire or electric shock.
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may result in fire.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in fire, electric shock
or other injury.
DO NOT PLACE HANDS, FINGERS OR FOREIGN OBJECTS IN INSERTION SLOTS OR GAPS.
Doing so may result in personal injury or damage to the product.
CAUTION
This symbol means important instructions. Failure to heed them can result in
injury or material property damage.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to the product. Return it
to your authorized Alpine dealer or the nearest Alpine Service Centre for
repairing.
PRECAUTIONS
Product Cleaning
Use a soft dry cloth for periodic cleaning of the product. For more severe
stains, please dampen the cloth with water only. Anything else has the chance
of dissolving the paint or damaging the plastic.
Temperature
Be sure the temperature inside the vehicle is between +60°C (+140°F) and 10°C
(+14°F) before turning your unit on.
Moisture Condensation
You may notice the CD playback sound wavering due to condensation. If this
happens, remove the disc from the player and wait about an hour for the
moisture to evaporate.
Damaged Disc
Do not attempt to play cracked, warped, or damaged discs. Playing a bad disc
could severely damage the playback mechanism.
Maintenance
If you have problems, do not attempt to repair the unit yourself. Return it to
your Alpine dealer or the nearest Alpine Service Station for servicing.
3-EN
Never Attempt the Following
Do not grip or pull out the disc while it is being pulled back into the player
by the automatic reloading mechanism. Do not attempt to insert a disc into the
unit when the unit power is off.
Inserting Discs
Your player accepts only one disc at a time for playback. Do not attempt to
load more than one disc. Make sure the label side is facing up when you insert
the disc. “ERROR” will be displayed on your player if you insert a disc
incorrectly. If “ERROR” continues to be displayed even though the disc has
been inserted correctly, push the RESET switch with a pointed object such as a
ballpoint pen. Playing a disc while driving on a very bumpy road may result in
skips, but this will not scratch the disc or damage the player.
New Discs
To prevent the CD from jamming, “ERROR” is displayed if discs with irregular
surfaces are inserted or if discs are inserted incorrectly. When a new disc is
ejected immediately after initial loading, use your finger to feel around the
inside of the center hole and outside edge of the disc. If you feel any small
bumps or irregularities, this could inhibit proper loading of the disc. To
remove the bumps, rub the inside edge of the hole and outside edge of the disc
with a ballpoint pen or other such instrument, then insert the disc again.
Centre Hole Centre Hole
New Disc
Bumps
Outside (Bumps)
Irregular Shaped Discs
Be sure to use round shape discs only for this unit and never use any special
shape discs. Use of special shape discs may cause damage to the mechanism.
Installation Location
Make sure the CDE-9850Ri will not be installed in a location subjected to:
· Direct sun and heat · High humidity and water · Excessive dust · Excessive
vibrations
Correct Handling
Do not drop the disc while handling. Hold the disc so you will not leave
fingerprints on the surface. Do not affix tape, paper, or gummed labels to the
disc. Do not write on the disc.
CORRECT
INCORRECT
CORRECT
Disc Cleaning
Fingerprints, dust, or soil on the surface of the disc could cause the CD
player to skip. For routine cleaning, wipe the playing surface with a clean,
soft cloth from the centre of the disc to the outer edge. If the surface is
heavily soiled, dampen a clean, soft cloth in a solution of mild neutral
detergent before cleaning the disc.
Disc Accessories
There are various accessories available on the market for protecting the disc
surface and improving sound quality. However, most of them will influence the
thickness and/or diameter of the disc. Using such accessories can cause the
disc to be out of standard specifications and may create operational problems.
We recommend not using these accessories on discs played in Alpine CD players.
Transparent Sheet
Disc Stabilizer
4-EN
On handling Compact Discs (CD/CD-R/CD-RW)
· Do not touch the surface. · Do not expose the disc to direct sunlight. · Do
not affix stickers or labels. · Clean the disc when it is dusty. · Make sure
that there are no bumps around the disc. · Do not use commercially available
disc accessories. Do not leave the disc in the car or the unit for a long
time. Never expose the disc to direct sunlight. Heat and humidity may damage
the CD and you may not be able to play it again.
To customers using CD-R/CD-RW
· If a CD-R/CD-RW cannot be played back, make sure the last recording session
was closed (finalized).
· Finalize the CD-R/CD-RW if necessary, and attempt playback again.
About media that can be played.
Use only compact discs with the label side showing the CD logo marks below.
If you use unspecified compact discs, correct performance cannot be
guaranteed. You can play CD-Rs (CD-Recordable)/CD-RWs (CD-ReWritable) which
have been recorded only on audio devices. You can also play CD-Rs/CD-RWs
containing MP3/WMA formatted audio files. · Some of the following CDs may not
play on this unit:
Flawed CDs, CDs with fingerprints, CDs exposed to extreme temperatures or
sunlight (e.g., left in the car or this unit), CDs recorded under unstable
conditions, CDs on which a recording failed or a re-recording was attempted,
copy-protected CDs which do not conform to the audio CD industry standard. ·
Use discs with MP3/WMA files written in a format compatible with this unit.
For details, see pages 13-14. · ROM data other than audio files contained in a
disc will not produce sound when played back.
· Windows Media and the Windows logo are trademarks, or registered trademarks
of Microsoft Corporation in the United States and /or other countries.
· Apple, the Apple logo and iPod are trademarks of Apple Computer, Inc.,
registered in the U.S. and other countries.
· “MPEG Layer-3 audio coding technology licensed from Fraunhofer llS and
Thomson.”
· “Supply of this product only conveys a license for private, noncommercial
use and does not convey a license nor imply any right to use this product in
any commercial (i.e. revenuegeneration) real time broadcasting (terrestrial,
satellite, cable and/or any other media), broadcasting/streaming via internet,
intranets and/or other networks or in other electronic content distribution
systems, such as pay-audio or audio-on-demand applications. An independent
license for such use is required. For details, please visit http://www.
mp3licensing.com.”
5-EN
Getting Started
(OPEN)
SOURCE/ POWER Rotary encoder
To close the front panel, press the left side until it locks as shown in the figure below.
3 Grasp the front panel firmly, slide to the left
pull to remove.
, then
Turning Power On and Off
Press SOURCE/POWER to turn on the unit. · The unit can be turned on by
pressing any other button except
(OPEN) and Rotary encoder. Press and hold SOURCE/POWER for at least 2 seconds
to turn off the unit. · The first time power is turned on, the volume will
start from level 12.
Detaching and Attaching the Front Panel
Be sure to push the Rotary encoder inside the unit before opening the front
panel so that the front panel will open completely, otherwise it may be
damaged.
Push the Rotary encoder inside When you push the Rotary encoder again, it pops
back out.
· The front panel may become hot in normal usage (especially the connector
terminals on the back of the front panel.) This is not a malfunction.
· To protect the front panel, place it in the supplied carrying case. · When
detaching the front panel, do not apply excessive force as it
may result in malfunction. · Do not leave the front panel open, or drive the
car with the panel
open as it may result in accident or malfunction.
Attaching
1 Insert the right side of the front panel into the main
unit. Align the groove on the front panel with the projections on the main
unit.
2 Push the left side of the front panel until it locks
firmly into the main unit.
The Rotary encoder pops out
Detaching
1 Turn off the unit power. 2 Press (OPEN) to open the front panel.
· Before attaching the front panel, make sure that there is no dirt or dust on
the connector terminals and no foreign object between the front panel and the
main unit.
· Attach the front panel carefully, holding the sides of the front panel to
avoid pushing buttons by mistake.
6-EN
Initial System Start-Up
Be sure to press the RESET switch when using the unit for the first time,
after changing the car battery, etc.
1 Turn off the unit power. 2 Press (OPEN) to open the front panel, then
remove it.
3 Press RESET with a ballpoint pen or similar pointed
object.
Radio
Rotary SOURCE/POWER
encoder
BAND
TUNE/A.ME
MODE
FUNC. Preset buttons (1 through 6)
RESET switch
Adjusting Volume
Turn the Rotary encoder until the desired sound is obtained.
Controllable With Remote Control The CDE-9850Ri can be controlled with an
optional Alpine remote control. For details, consult your Alpine dealer. Point
the optional remote control transmitter at the remote control sensor. Remote
control sensor
Connectable to Remote Control Interface Box You can operate this unit from the
vehicle’s control unit when an Alpine Remote Control Interface Box (optional)
is connected. For details, contact your Alpine dealer.
Listening to Radio
1 Press SOURCE/POWER until a radio frequency
appears on the display.
2 Press BAND repeatedly until the desired radio band
is displayed.
F1 (FM1) F2 (FM2) F3 (FM3) MW LW F1 (FM1)
3 Press TUNE/A.ME to select the tuning mode.
DX SEEK (Distance mode) SEEK (Local mode) OFF (Manual mode) DX SEEK
· The initial mode is Distance mode.
Distance mode: Both strong and weak stations will be automatically tuned in (Automatic Seek Tuning).
Local mode: Only strong stations will be automatically tuned in (Automatic Seek Tuning).
Manual mode: The frequency is manually tuned in steps (Manual tuning).
4 Press
or
Holding down
continuously.
to tune in the desired station.
or
will change the frequency
Manual Storing of Station Presets
1 Select the radio band and tune in a desired radio
station you wish to store in the preset memory.
2 Press and hold, for at least 2 seconds, any one of the
preset buttons (1 through 6) into which you wish to store the station. The
selected station is stored. The display shows the band, preset number and
station frequency memorized.
7-EN
· A total of 30 stations can be stored in the preset memory (6 stations for
each band; FM1, FM2, FM3, MW and LW).
· If you store a station in a preset memory which already has a station, the
current station will be cleared and replaced with the new station.
· If the “FUNC” indicator is illuminated, turn off the indicator by pressing
FUNC., then you can perform the operation.
Automatic Memory of Station Presets
1 Press BAND repeatedly until the desired radio band
is displayed.
2 Press and hold TUNE/A.ME for at least 2 seconds.
The frequency on the display continues to change while the automatic memory is
in progress. The tuner will automatically seek and store 6 strong stations in
the selected band. They will be stored into buttons 1 to 6 in order of signal
strength. When the automatic memory has been completed, the tuner goes to the
station stored in preset location No.1.
· If no stations are stored, the tuner will return to the original station you
were listening to before the auto memory procedure began.
Tuning to Preset Stations
1 Press BAND repeatedly until the desired band is
displayed.
2 Press any one of the station preset buttons (1
through 6) that has your desired radio station in memory. The display shows
the band, preset number and frequency of the station selected.
· If the “FUNC” indicator is illuminated, turn off the indicator by pressing
FUNC., then you can perform the operation.
Frequency Search Function
You can search for a radio station by its frequency.
1 Press and hold for at least 2 seconds in Radio
mode to activate Frequency Search mode.
2 Turn the Rotary encoder to select the desired
frequency.
3 Press MODE to receive the selected frequency.
· Press and hold for at least 2 seconds in the search mode to cancel. Or, the
search mode will be cancelled when an operation has not been performed in 10
seconds.
RDS
Rotary TA encoder
MENU FUNC.
MODE
1 AF NEWS 2 3 PTY TITLE
Setting RDS Reception Mode and Receiving RDS Stations
The RDS (Radio Data System) is a radio information system using the 57 kHz subcarrier of regular FM broadcast. The RDS allows you to receive a variety of information such as traffic information, station names, and to automatically re-tune to a stronger transmitter that is broadcasting the same programme.
1 Press FUNC. so that the “FUNC” indicator lights up.
2 Press 1 AF to activate the RDS mode.
3 Press
or
station.
to tune in the desired RDS
4 Press 1 AF again to deactivate the RDS mode.
5 Press FUNC. to activate the normal mode.
The “FUNC” indicator goes out.
· When the “Setting PTY31 (Emergency Broadcast) reception” (refer to page 9) is set to on, if the unit receives the PTY31 (Emergency Broadcast) signal, the unit will show “ALARM” in the display automatically.
The RDS digital data includes the following:
PI
Programme Identification
PS Programme Service Name
AF List of Alternative Frequencies
TP
Traffic Programme
TA
Traffic Announcement
PTY Programme Type
EON Enhanced Other Networks
8-EN
Recalling Preset RDS Stations
1 Press FUNC. so that the “FUNC” indicator lights up.
2 Press 1 AF to activate the RDS mode.
3 Press FUNC. to activate the normal mode.
The “FUNC” indicator goes out.
4 Make sure that the “FUNC” indicator light goes out,
then press the preset button in which your desired RDS station is preset. If
the preset station’s signal is weak, the unit automatically searches and tunes
to a stronger station in the AF (Alternative Frequencies) list.
5 If the preset station and the stations in the AF list
cannot be received: When the PI SEEK setting is on (refer to “PI SEEK Setting”
on page 9), the unit searches again for a station in the PI (Programme
Identification) list. If there are still no stations receivable in the area,
the unit displays the frequency of the preset station and the preset number
disappears. If the signal level of the Regional (Local) station being tuned
becomes too weak to receive, press the same preset button to tune in a
Regional station in other district.
· For presetting the RDS stations, refer to the Radio Operation section. The
RDS stations can be preset in the F1, F2 and F3 bands only.
Receiving RDS Regional (Local) Stations
1 Press MENU to select the SETUP mode, then press
MODE.
SETUP mode is activated.
BASS ENGINE SETUP RETURN (OFF) BASS ENGINE
2 Press
or
to select the RDS REGIONAL
mode, then press MODE.
3 Turn the Rotary encoder to select ON or OFF.
In the OFF mode, the unit automatically keeps receiving the related local RDS
station.
4 Press MENU to select RETURN.
After 2 seconds, the unit returns to normal mode. Pressing and holding MENU
for at least 2 seconds will return to normal mode.
PI SEEK Setting
1 Press MENU to select the SETUP mode, then press
MODE. SETUP mode is activated.
BASS ENGINE SETUP RETURN (OFF) BASS ENGINE
2 Press
or
MODE.
to select the PI SEEK, then press
3 Turn the Rotary encoder to select ON or OFF.
4 Press MENU to select RETURN.
After 2 seconds, the unit returns to normal mode. Pressing and holding MENU
for at least 2 seconds will return to normal mode.
Setting PTY31 (Emergency Broadcast) reception
Turn PTY31 (Emergency Broadcast) reception ON/OFF.
1 Press MENU to select SETUP mode, then press
MODE. The SETUP mode is activated.
BASS ENGINE SETUP RETURN (OFF) BASS ENGINE
2 Press
or
to the select ALERT PTY31
mode, then press MODE.
3 Turn the Rotary encoder to select ON or OFF.
If you set ON, emergency broadcast are received regardless of source. “ALARM”
is displayed during reception.
4 Press MENU to select RETURN.
After 2 seconds, the unit returns to normal mode. Pressing and holding MENU
for at least 2 seconds will return to normal mode. When an emergency broadcast
is received, the volume level will be automatically changed to the memorized
level in the traffic information mode. For details, refer to “Receiving
Traffic Information.”
9-EN
Receiving Traffic Information
1 Press TA so that the “TA” indicator lights up.
2 Press
or
to select your desired traffic
information station.
When a traffic information station is tuned in, the “TP” indicator lights up. Traffic information is heard only when it is being broadcast. If traffic information is not being broadcast, the unit is set in the standby mode. When a traffic information broadcast begins, the unit automatically receives it and the display shows “TRF-INFO” for a few seconds. When the traffic information broadcast is over, the unit will automatically set in the standby mode.
· If the traffic information broadcast signal falls below a certain level, the
unit remains in the receiving mode for 1 minute. If the signal remains below a
certain level for over 1 minute, the “TA” indicator blinks.
· If you do not want to listen to the traffic information being received,
lightly press TA to skip that traffic information message. The TA mode will
remain in the ON position to receive the next traffic information message.
· If the volume level is changed while receiving traffic information, the
changed volume level will be memorized. When traffic information is received
next time, the volume level will be automatically adjusted to the level
memorized.
· In the TA mode, the SEEK tuning selects only the TP stations.
PTY (Programme Type) Tuning
1 Press FUNC. so that the “FUNC” indicator lights up.
2 Press 3 PTY to activate the PTY mode, while the
unit is in Radio (FM receiving) mode. The Programme Type of the station being
currently received will be displayed for 10 seconds. If there is no receivable
PTY broadcast, “NO PTY” will be displayed for 10 seconds. If no RDS station
can be received, the display shows “NO PTY.”
· If no operation is performed within 10 seconds after pressing 3 PTY, the PTY mode will be automatically cancelled.
3 Press
or
within 10 seconds after
activating the PTY mode to choose the desired
programme type while the PTY (programme type) is
being displayed.
Each press scrolls the programme type by one.
LIGHT M CLASSICS OTHER M
5 Press FUNC. to activate the normal mode.
The “FUNC” indicator goes out.
· Operate the unit while the “FUNC” indicator lights up. If no operation is
performed within 10 seconds, the “FUNC” indicator goes out.
Receiving Traffic Information While Playing CD or Radio
1 Press TA so that the “TA” indicator lights up.
2 Press
or
to select a traffic information
station if necessary.
When a traffic information broadcast starts, the unit automatically mutes the CD player or the regular FM broadcast. When the traffic information broadcast finishes, the unit automatically returns to the original source play before the traffic information broadcast began.
When traffic information stations cannot be received: In the tuner mode: When the TP signal can no longer be received for over 1 minute, the “TA” indicator blinks.
In the CD mode: When the TP signal can no longer be received, the traffic information station of another frequency will be selected automatically.
· The receiver is equipped with the EON (Enhanced Other Networks) function in
order to keep track of additional alternate frequencies to the AF list. The
“EON” indicator lights up while an RDS EON station is being received. If the
station being received does not broadcast the traffic information, the
receiver automatically tunes in the related station that broadcasts the
traffic information when it occurs.
3 Press TA to deactivate the Traffic Information mode.
The “TA” indicator goes out.
4 Press 3 PTY within 10 seconds after selecting the
programme type to start searching for a station in the selected programme
type. The chosen programme type display blinks during searching and lights
when a station is found.
If no PTY station is found, “NO PTY” will be displayed for 10 seconds.
10-EN
Priority News
This function allows you to preset to give priority to the News programme. You
will never miss the News programme as the unit automatically gives priority to
the News programme whenever it begins broadcasting, and interrupts the
programme you are currently listening. This feature is functional when your
unit is set to a mode other than the MW and LW modes.
1 Press FUNC. so that the “FUNC” indicator lights up
while the unit is in Radio (FM receiving) mode.
2 Press NEWS 2 to activate the PRIORITY NEWS
mode. The “NEWS” indicator appears in the display. To disable the PRIORITY
NEWS function, press NEWS 2.
· In the PRIORITY NEWS function, unlike in the TA function, the volume does
not increase automatically.
3 Press FUNC. to activate the normal mode, while the
unit is in Radio (FM receiving) mode. The “FUNC” indicator light goes out.
Displaying Radio Text
Text messages from a radio station can be displayed.
Press TITLE while receiving FM in the radio mode to select the Radio Text
display.
The display will change every time the button is pressed.
If there is PS (Programme Service NAME): PS (Programme Service Name)* Radio
Text PS (Programme Service Name)
- Press and hold TITLE for at least 2 seconds if PS is displayed in the radio mode, “FREQUENCY” will be displayed for 5 seconds.
If there is no PS (Programme Service Name): FREQUENCY Radio Text FREQUENCY
The display shows “WAITING” for a few seconds, then starts scrolling the text message.
· If there is no receivable text message or the unit cannot receive a text message properly, the display shows “NO TEXT.”
CD/MP3/WMA
(OPEN)
Rotary SOURCE/POWER
encoder
/
MODE
FUNC.
45
TITLE
Playback
1 Press (OPEN).
The front panel will open.
2 Insert a disc with the label side facing up.
The disc will be pulled into the unit automatically.
Close the front panel manually. When a disc is already inserted, press SOURCE/POWER to switch to the CD mode.
The mode will change every time the button is pressed.
TUNER DISC IPOD* TUNER
- Only when the iPod is connected.
3 While playing back MP3/WMA, press or to
select the desired folder. Pressing and holding or will change folders
continuously.
4 Press
or
to select the desired track (file).
Returning to the beginning of the current track (file):
Press
.
Fast backward:
Press and hold
.
Advancing to the beginning of the next track (file):
Press
.
Fast forward:
Press and hold
.
5 To pause playback, press / .
Pressing / again will resume playback.
11-EN
6 After pressing (OPEN) to open the front panel,
press to eject the disc.
· Do not remove a CD during its eject cycle. Do not load more than one disc at
a time. A malfunction may result from doing either.
· If the CD does not eject, press and hold for at least 2 seconds. · The CD-
player can play discs containing audio data, MP3 data and
WMA data. · A WMA format file that is protected by DRM (Digital Rights
Management) cannot be played back on this unit. · The track display for
MP3/WMA data playback is the file numbers
recorded on the disc. · The playback time may not be correctly displayed when
a VBR
(Variable Bit Rate) recorded file is played back.
MP3/WMA Play Display The folder number and file number will be displayed as
described below.
F01 T03 10’15
Folder number File number Elapsed time
display
display
· Press TITLE to switch the display. See “Displaying the Text” (page 16) for
information about display switching.
· If the folder number or file number is 3 digits, F or T becomes numbers of
hundred rank.
Repeat Play
Press 4 to play back repeatedly the track being played. The track (file) will
be played repeatedly. Press 4 again and select off to deactivate repeat play.
CD mode :
: Only a track is repeatedly played back.
MP3/WMA mode :
M.I.X. (Random Play)
Press 5 in the play or pause mode. The tracks (files) on the disc will be
played back in random sequence. To cancel M.I.X. play, press 5 again. CD mode
:
: The tracks are played back in random sequence.
MP3/WMA mode :
: Only files in a folder are played back in random sequence.
: The files are played back in random sequence.
Searching from CD Text
Tracks can be searched and played by using the CD text on the disc. In the
case of discs that do not support text, searches can be made by using the
track numbers.
1 Press during play.
This will set the search mode.
2 Turn the Rotary encoder to select the desired
track, then press MODE. This will play the selected track. · Press and hold
for at least 2 seconds in the search mode to cancel. Or, the search mode will
be cancelled when an operation has not been performed in 10 seconds. · CD text
search cannot be made during M.I.X. play.
: Only a file is repeatedly played back. : Only files in a folder are repeatedly played back.
12-EN
File/Folder Name Search (concerning MP3/WMA)
You can display and search the folder and file name while listening to the
file currently being played back.
1 Press to activate Search selection mode during
MP3/WMA playback.
2 Turn the Rotary encoder to select Folder Name
Search mode or File Name Search mode, then press .
Quick Search
You can search for tracks (files).
1 Press and hold for at least 2 seconds in the CD/
MP3/WMA mode to activate Quick Search mode.
2 Turn the Rotary encoder to select a desired track
(file). The selected track is played back immediately.
· Press and hold for at least 2 seconds in the search mode to cancel. Or, the
search mode will be cancelled when an operation has not been performed in 10
seconds.
Folder Name Search mode
3 Turn the Rotary encoder to select the desired
folder.
4 Press / to play back the first file in the selected
folder.
· Press and hold for at least 2 seconds in the search mode to cancel. Or, the
search mode will be cancelled when an operation has not been performed in 10
seconds.
· While in Folder Name Search mode, press to switch to File Name Search mode.
· “ROOT” is displayed for the root folder which does not have folder name.
· Folder Name search cannot be made during M.I.X. play. · Press FUNC. in the
Search mode to return to the previous step. · Folder search cannot be
performed if the disc only has root folder. · If there is no file in the
folder when selecting the folder search mode,
“NO FILE” will be displayed for 2 seconds.
File Name Search mode
3 Press or to select another Folder.
4 Select the desired file by turning the Rotary
encoder.
5 Press MODE to playback the selected file.
· Press and hold for at least 2 seconds in the search mode to cancel. Or, the
search mode will be cancelled when an operation has not been performed in 10
seconds.
· File Name search cannot be made during M.I.X. play. · Press FUNC. in the
Search mode to return to the previous step.
About MP3/WMA
CAUTION Except for private use, duplicating audio data (including MP3/ WMA
data) or distributing, transferring, or copying it, whether for free or for a
fee, without permission of the copyright holder is strictly prohibited by the
Copyright Act and by international treaty.
What is MP3?
MP3, whose official name is “MPEG-1 Audio Layer 3,” is a compression standard
prescribed by the ISO, the International Standardization Organization and MPEG
which is a joint activity institution of the IEC.
MP3 files contain compressed audio data. MP3 encoding is capable of
compressing audio data at extremely high ratios, reducing the size of music
files to as much as one-tenth their original size. This is achieved while
still maintaining near CD quality. The MP3 format realizes such high
compression ratios by eliminating the sounds that are either inaudible to the
human ear or masked by other sounds.
What is WMA?
WMA, or “Windows MediaTM Audio,” is compressed audio data. WMA is similar to
MP3 audio data and can achieve CD quality sound with small file sizes.
Method for creating MP3/WMA files
Audio data is compressed by using MP3/WMA specified software. For details on
creating MP3/WMA files, refer to the user’s manual for that software. MP3/WMA
files that can be played back by this device have the file extension “mp3” /
“wma”. Files with no extension cannot be played back. (WMA ver. 7.1, 8 and 9
are supported)
13-EN
Supported playback sampling rates and bit rates
MP3
Sampling rates: 48 kHz, 44.1 kHz, 32 kHz, 24 kHz, 22.05 kHz,
16 kHz, 12 kHz, 11.025 kHz, 8 kHz
Bit rates:
8 – 320 kbps
WMA
Sampling rates: 48 kHz, 44.1 kHz, 32 kHz
Bit rates:
48 – 192 kbps
Note that for sampling rates, this device’s frame display (page 16) may not display correctly. This device may not play back correctly depending on sampling rates.
ID3 tags/WMA tags
This device supports ID3 tag v1 and v2, and WMA tag. If tag data is in an
MP3/WMA file, this device can display the title (track title), artist name,
and album name ID3 tag/WMA tag data.
This device can only display single-byte alphanumeric characters (up to 30 for
ID3 tags and up to 15 for WMA tags) and the underscore. For non-supported
characters, “NO SUPPORT” is displayed. The tag information may not be
correctly displayed, depending on the contents.
Producing MP3/WMA discs
MP3/WMA files are prepared, then written to a CD-R or CD-RW using CD-R writing
software. A disc can hold up to 510 files/ folders (including Root Folders).
However, the maximum number of folders is 255.
Media supported
The media that this device can play back are CD-ROMs, CD-Rs, and CD-RWs.
Corresponding File Systems
This device supports discs formatted with ISO9660 Level 1 or Level 2.
Under the ISO9660 standard, there are some restrictions to remember. The
maximum nested folder depth is 8 (including the root directory). The number of
characters for a folder/file name is limited. Valid characters for folder/file
names are letters A-Z (all caps), numbers 0-9, and `_’ (underscore).
This device also can play back discs in Joliet, Romeo, etc., and other
standards that conform to ISO9660. However, sometimes the file names, folder
names, etc., are not displayed correctly.
Formats supported
This device supports CD-ROM XA, Mixed Mode CD, Enhanced CD (CD-Extra) and
Multi-Session. This device cannot correctly play back discs recorded with
Track At Once or packet writing.
Order of files The unit plays the files in the order that the writing software
writes them. Therefore, the playing order may not be the same as the order you
input. The playback order of the folders and files is as follows. However, the
folder and file playback order differs from the folder and file number
indicated on the display.
Root folder
Folder
MP3/WMA File
Terminology
Bit rate This is the “sound” compression rate specified for encoding. The
higher the bit rate, the higher the sound quality, but also the larger the
files.
Sampling rate This value shows how many times per second the data is sampled
(recorded). For example, music CDs use a sampling rate of 44.1 kHz, so the
sound is sampled (recorded) 44,100 times per second. The higher the sampling
rate, the higher the sound quality, but also the larger the volume of data.
Encoding Converting music CDs, WAVE (AIFF) files, and other sound files into
the specified audio compression format.
Tag Song information such as track titles, artist names, album names, etc.,
written into MP3/WMA files. MP3: ID3 tag WMA: WMA tag
Root folder The root folder is found at the top of the file system. The root
folder contains all folders and files.
14-EN
Sound Setting
Rotary encoder SOURCE/POWER BAND MENU
Setting the Bass Centre Frequency
3-1 Press SOURCE/POWER to select the desired bass
centre frequency.
80Hz 100Hz 120Hz 60Hz 80Hz Emphasize the displayed bass frequency ranges.
Setting the Bass Bandwidth
3-2 Press BAND to select the desired bass bandwidth.
MODE
Adjusting Bass/Treble/Balance (Between Left and Right)/Fader (Between Front
and Rear)/Defeat
1 Press MODE repeatedly to choose the desired
mode.
Each press changes the mode as follows:
BASS TREBLE SUBW* BALANCE FADER DEFEAT VOLUME BASS
Bass Level: 7 ~ +10 Treble Level: 7 ~ +7 Subwoofer : 0 ~ +15 Balance : L15 ~
R15 Fader : R15 ~ F15 Defeat : ON/OFF Volume : 0 ~ 35
· If MODE is not pressed within 5 seconds after selecting the BASS, TREBLE,
BALANCE, FADER, DEFEAT or SUBW mode, the unit automatically returns to normal
mode.
- When the subwoofer mode is set to OFF, its level cannot be adjusted.
2 Turn the Rotary encoder until the desired sound is
obtained in each mode. By setting Defeat ON, previously adjusted settings of BASS and TREBLE will return to the factory defaults.
Setting the Bass Control
You can change the Bass Frequency emphasis to create your own tonal
preference.
1 Press MENU to select the BASS ENGINE mode, then
press MODE.
BASS ENGINE SETUP RETURN (OFF) BASS ENGINE
2 Press
or
to select the BASS (bass Centre
frequency) control mode.
BASS TREBLE
Change the boosted bass bandwidth to wide or narrow. A wide setting will boost a wide range of frequencies above and below the centre frequency. A narrower setting will boost only frequencies near the centre frequency.
Setting the Bass Level
3-3*1Turn the Rotary encoder to select the desired
bass level (7~+10). You can emphasize or weaken the bass level.
4 Press MENU to select RETURN.
After 2 seconds, the unit returns to normal mode. Pressing and holding MENU
for at least 2 seconds will return to normal mode.
· If no operation is performed within 60 seconds, the bass control
setting will be turned off automatically.
· The bass level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
bass frequency and bass band width settings adjusted for one source
are effective for all other sources (FM, MW (LW), CD etc.).
· Depending on the connected devices, some functions and display
indications do not work. However, Bass Level is still adjustable if an
audio processor with the Bass function is connected.
· This function is inoperable when DEFEAT is set to ON.
· If you press
or
in the bass control mode, the unit
changes to the treble control mode. *1 The adjustment can also be made by pressing MODE. Refer to
“Adjusting Bass/Treble/Balance (Between Left and Right)/Fader
(Between Front and Rear)/Defeat” (page 15).
Bass level indicator’s display
Bass level is usually displayed.
15-EN
Setting the Treble Control
You can change the Treble Frequency emphasis to create your own tonal
preference.
1 Press MENU to select the BASS ENGINE mode, then
press MODE.
BASS ENGINE SETUP RETURN (OFF) BASS ENGINE
2 Press
or
to select the TREBLE (Treble
Centre Frequency) control mode.
BASS TREBLE
Setting the Treble Centre Frequency
3-1 Press SOURCE/POWER to select the desired treble
Centre frequency.
10.0kHz 12.5kHz 15.0kHz 7.5kHz 10.0kHz Emphasize the displayed treble
frequency ranges.
Setting the Treble Level
3-2*2Turn the Rotary encoder to select the desired
treble level (7~+7). You can emphasize the treble level.
4 Press MENU to select RETURN.
After 2 seconds, the unit returns to normal mode. Pressing and holding MENU
for at least 2 seconds will return to normal mode.
· If no operation is performed within 60 seconds, the treble control
setting will be turned off automatically.
· The treble level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
Treble frequency settings adjusted for one source are effective for all
other sources (FM, MW (LW), CD, etc.).
· Depending on the connected devices, some functions and display
indications do not work. However, Treble Level is still adjustable if
an audio processor with the Treble function is connected.
· This function is inoperable when DEFEAT is set to ON.
· If you press
or
in the treble control mode, the unit
changes to the bass control mode. *2 The adjustment can also be made by pressing MODE. Refer to
“Adjusting Bass/Treble/Balance (Between Left and Right)/Fader
(Between Front and Rear)/Defeat” (page 15).
Turning Loudness On/Off
Loudness introduces a special low- and high-frequency emphasis at low
listening levels. This compensates for the ear’s decreased sensitivity to bass
and treble sound.
Press and hold MODE for at least 2 seconds to activate or deactivate the
loudness mode. “LD” indicator lights.
Other Functions
TITLE
Displaying the Text
Text information, such as the disc name and the track name, will be displayed
if playing a CD text compatible disc. It is also possible to display the
folder name, the file name, and the tag, etc., while playing MP3/WMA files.
Press TITLE. The display will change every time the button is pressed.
The display in Radio mode: If there is PS (Programme Service NAME)
PS (Programme Service Name)1 Radio Text PS (Programme Service Name) If there
is no PS (Programme Service Name) FREQUENCY Radio Text FREQUENCY The display
in CD mode: TRACK NO./ELAPSED TIME TEXT (DISC NAME)2 TEXT (TRACK NAME)2
TRACK NO./ELAPSED TIME The display in MP3/WMA mode: FOLDER NO./FILE
NO./ELAPSED TIME FOLDER NAME3 FILE NAME3 ARTIST NAME4 ALBUM NAME4 TRACK
NAME4 FRAME5 FOLDER NO./FILE NO./ELAPSED TIME 1 Press and hold TITLE for at
least 2 seconds in the PS display mode, “FREQUENCY” will be displayed for 5
seconds. 2 Displayed during playback of a disc with CD Text. If there is no
Text (Disc Name or Track Name), “DISC TEXT”/ “TRACK TEXT” is displayed. 3
“ROOT” is displayed for the folder name of the root folder which does not have
folder name. If there is no folder name or file name, “FOLDER”/”FILE” is
displayed. 4 ID3 tag/WMA tag If an MP3/WMA file contains ID3 tag/WMA tag
information, the ID3 tag/WMA tag information is displayed (track name, artist
name, and album name). All other tag data is ignored. If there is no tag
information, “ARTIST”/”ALBUM”/”SONG” will be displayed. If “SCROLL AUTO” is
set in “Scroll Setting (TEXT SCROLL)” (page 18), tag information will
automatically be scrolled. 5 The recording sampling rate and bit rate of the
MP3/WMA file are displayed. A WMA file of variable bit rate displays the
average bit rate.
16-EN
About the indication display
When displaying Text, the following indicators are lit according to the mode.
The position of a song being played back is shown lit in the total number of
songs shown. The display example is as shown below. Also lights when operation
,such as fast forward, etc.,is performed. Lights up when a disc is inserted
Song position display example
· For example, when the 5th of 10 songs in the disc is played back,
”
” is displayed.
Indicator/ Mode
CD Mode
MP3/WMA Mode
iPod Mode
While
—
displaying
—
Folder Name
While
—
displaying
—
File Name
While
While
—
displaying
displaying
Artist Name Artist Name
While displaying Text (Disc Name)
While displaying Album Name*
While displaying Album Name*
While displaying Text (Track Name)
While displaying Track Name*
While displaying Track Name*
*Tag information
About “Text”
Text: Text compatible CDs contain text information such as the disc name and
track name. Such text information is referred to as “text.”
· Some characters may not be displayed correctly with this device, depending
on the character type.
· When the Scroll Setting (page 18) is set to “SCROLL MANU,” press and hold
TITLE for at least 2 seconds to scroll the Text information only once (TEXT
DISPLAY, FOLDER NAME DISPLAY, FILE NAME DISPLAY or TAG DISPLAY mode).
· “NO SUPPORT” is displayed when the desired text information cannot be
displayed on this unit.
· The text or tag information may not be correctly displayed, depending on the
contents.
17-EN
SETUP
You can flexibly customize the unit to suit your own preferences and usage.
Choose the SETUP menu from Sound Customizing, Visual Customizing, etc., to
select your desired setting.
Rotary encoder MENU
MODE
A typical SETUP procedure is shown in steps 1 to 4 as follows. See below for further information about each SETUP menu.
1 Press MENU to select the SETUP mode, then press
MODE.
BASS ENGINE SETUP RETURN (OFF) BASS ENGINE
2 Press
or
to select the desired SETUP
menu, then press MODE.
(e.g. Select SUBWOOFER)
FM LEVEL RDS REGIONAL1 PI SEEK2 ALERT PTY313 ILLUMINATION DIMMER SUBWOOFER
(SUBW SYSTEM)4 PLAY MODE
SCROLL TYPE TEXT SCROLL POWER IC DEMO
FM LEVEL
1 Refer to “Receiving RDS Regional (Local) Stations” (page 9) 2 Refer to “PI SEEK Setting” (page 9) 3 Refer to “Setting PTY31 (Emergency Broadcast) reception” (page 9) 4 Displayed only when SUBW is ON.
3 Turn the Rotary encoder to change the setting.
(e.g. Select SUBW ON or SUBW OFF.)
4 Press MENU to select RETURN.
After 2 seconds, the unit returns to normal mode. Pressing and holding MENU
for at least 2 seconds will return to normal mode.
Sound Customizing
Adjusting Source Signal Levels
FM-LEVEL HI (Initial setting) / FM-LEVEL LOW
If the difference in volume level between the CD player and FM radio is too
great, adjust the FM signal level.
Subwoofer On and Off
SUBW ON (Initial setting) / SUBW OFF
When the subwoofer is on, perform the steps below to adjust the subwoofer
output level.
1 In the normal mode, press MODE repeatedly to select the SUBW mode.
BASS TREBLE SUBW BALANCE FADER DEFEAT VOLUME BASS 2 Adjust the level by
turning the Rotary encoder.
Setting the Subwoofer System
SUBW SYS1 (Initial setting) / SUBW SYS2
Select either SYS1 or SYS2 for the desired subwoofer effect.
SUBW SYS1: Subwoofer level changes according to the main volume setting.
SUBW SYS2: Subwoofer level change is different from the main volume setting.
For example, even at low volume settings, the subwoofer is still audible.
Visual Customizing
Changing Lighting Colour
ILLUMI BLUE (Initial setting) / RED
You can change the lighting colour of the buttons.
BLUE RED
Dimmer Control
DIMMER AUTO (Initial setting) / DIMMER MANU
Set the DIMMER control to AUTO to decrease the illumination brightness of the
unit with the head lights of the vehicle ON. This mode is useful if you feel
the unit’s backlighting is too bright at night.
· If your vehicle should have a dimmer control for the dashboardlights, never
connect the DIMMER cable (orange) of the radio to this dimmer control.
Scroll Type Setting
SCROLL TYPE1 / SCROLL TYPE2 (Initial setting)
Choose from two scrolling methods. Select the type you prefer.
Scroll Setting (TEXT SCROLL)
SCROLL AUTO / SCROLL MANU (Initial setting)
This CD player can scroll the disc and track names recorded on CDTEXT discs,
as well as the text information of MP3/WMA files, folder names, and tags.
SCROLL AUTO: The CD text information, the text information of folder and file
names, and the tags are scrolled automatically. Also, tag information is
automatically scrolled without pressing TITLE in the tag information display
mode.
SCROLL MANU: The display is scrolled when a disc is loaded or when a track is
changed, etc.
18-EN
· The unit scrolls CD text names, folder names, file names or tag display.
Demonstration
DEMO ON / DEMO OFF (Initial setting) This unit has a demonstration feature for
the display.
· To quit Demo mode, set to DEMO OFF.
MP3/WMA
Playing MP3/WMA Data (PLAY MODE)
CDDA (Initial setting) / CDDA/MP3
This product can playback CDs containing both CD and MP3/WMA data. However, in some situations (some enhanced CDs), playback may be difficult. For these special cases, you can select playback of CD data only. When a disc contains both CD or the MP3/WMA data, playback starts from the CD data portion of the disc.
CDDA :
Only CD data can be played back.
CDDA/MP3 : Both CD data and MP3/WMA file tracks can be played back.
· Perform this setting before inserting a disc. If a disc has already been inserted, perform the setting after you remove the disc.
External Device
Connecting to an External Amplifier
POWER IC ON (Initial setting) / POWER IC OFF
When an external amplifier is connected, sound quality can be improved by
stopping the power supply of the built-in amplifier.
POWER IC OFF : Use this mode when the front pre-amplifier of the unit is used
to drive an external amplifier connected to the speakers. In this setting, the
head unit’s internal amplifier has no output to drive speakers.
POWER IC ON : The speakers are driven by the built-in amplifier.
SPEAKER RIGHT FRONT
Speakers
Front right
SPEAKER RIGHT REAR
SPEAKER LEFT REAR
Rear right
Rear left
SPEAKER LEFT FRONT
Front left
· No sound is produced by the system when the power output is set to OFF.
Amplifier
Front left
Front right
19-EN
iPodTM (Optional)
Rotary
encoder SOURCE/POWER
/
MODE
FUNC.
45
6 TITLE
An iPodTM, iPodTM mini or iPodTM nano can be connected to the CDE-9850Ri by
using the FULL SPEEDTM Connection Cable (supplied). When the CDE-9850Ri is
connected by using the cable, the controls on the iPodTM are not functional.
About iPodsTM usable with this unit The unit can be used with third generation
and above iPodTM photo, iPodTM minis or iPodTM nano. iPodTM Shuffle cannot be
used, however.
· Touch wheel or scroll wheel type iPods without the dock connector cannot be
connected to the unit.
· The unit can be used with the following iPod versions. Correct function of
earlier versions cannot be guranteed.
Third generation iPod:Ver. 2.3 Forth generation iPod:Ver. 3.0.2 iPod
photo:Ver.1.0 iPod mini:Ver. 1.3 iPod nano:Ver. 1.0
· The unit cannot be used with the software versions earlier than 22nd
Feb.2005. For details about “iPod Software Update”, refer to the iPod
Instruction Manual.
Playback
1 Press SOURCE/POWER to switch to the iPod
mode.
2 Press
or
to select the desired song.
Return to the beginning of the current song:
Press
.
Fast backward:
Press and hold
.
Advance to the beginning of the next song:
Press
.
Fast forward:
Press and hold
.
3 To pause playback, press / .
Pressing / again will resume playback.
· If a song is playing on the iPod when it is connected to the CDE-9850Ri, it
will continue playing after the connection.
Searching for a desired Song
An iPod can contain hundreds of songs. By keeping these songs organized in
playlists, the CDE-9850Ri can use these to ease song searches.
Searching by Playlist
1 Press to activate the search selection mode. 2 Turn the Rotary encoder to
select the PLAYLIST
search mode, then press .
PLAYLIST ARTIST ALBUM SONG PLAYLIST
31 Turn the Rotary encoder to select the desired
Playlist.
4 Press / .
The selected playlist is played back.
To search for a song in the selected playlist
1 After selecting the playlist in step 31, press to change to the song search
mode of the selected playlist.
2 Turn the Rotary encoder to select a song and press MODE. The selected song
is played back.
· Press and hold for at least 2 seconds in the search mode to cancel. Or, the
search mode will be canceled when an operation has not been performed in 10
seconds.
· In the search mode, pressing FUNC. will return to the previous mode.
· All songs in the iPod are played back by selecting the stored “iPod name” in
step 31.
· Playlist search cannot be made during M.I.X. play. · “NO SONG” will be
displayed if there are no songs in the selected
playlist in the PLAYLIST search mode.
Searching by artist name
1 Press to activate the search selection mode. 2 Turn the Rotary encoder to
select the ARTIST
search mode, then press .
PLAYLIST ARTIST ALBUM SONG PLAYLIST
32 Turn the Rotary encoder to select the desired
Artist.
4 Press / .
All the songs of the selected Artist are played back.
20-EN
To search for an album of the selected artist
1 After selecting the artist in step 32, press to change to the album search
mode of the selected artist.
21Turn the Rotary encoder to select an album.
3 Press / to play back all songs of the selected album.
To search for a song of the selected album
1 After selecting the album in step 21, press to change to the song search
mode of the selected album.
2 Turn the Rotary encoder to select a song and press MODE. The selected song
is played back.
· Press and hold for at least 2 seconds in the search mode to cancel. Or, the
search mode will be cancelled when an operation has not been performed in 10
seconds.
· In the search mode, pressing FUNC. will return to the previous mode.
· If you choose ALL in step 32, and you press / , all songs in iPod are
played back. If you choose ALL, and you press , the ALBUM search mode for all
artists is activated.
· If you choose ALL in step 21, and you press / , all songs of the selected
artist are played back. If you choose ALL, and you press , the SONG search
mode for the selected artist is activated.
· Artist name search cannot be made during M.I.X. play.
Searching by album name
1 Press to activate the search selection mode. 2 Turn the Rotary encoder to
select the ALBUM
search mode, then press .
PLAYLIST ARTIST ALBUM SONG PLAYLIST
33 Turn the Rotary encoder to select the desired
Album.
4 Press / .
All the songs of the selected Albums are played back.
To search for a song of the selected album
1 After selecting the album in step 3*3, press to change to the song search
mode of the selected album.
2 Turn the Rotary encoder to select a song and press MODE. The selected song
is played back.
· Press and hold for at least 2 seconds in the search mode to cancel. Or, the
search mode will be canceled when an operation has not been performed in 10
seconds.
· In the search mode, pressing FUNC. will return to the previous mode.
· If you choose ALL in step 3*3, and you press / , All songs in iPod are
played back. If you choose ALL, and you press , the SONG search mode for all
albums is activated.
· Album name search cannot be made during M.I.X. play.
Searching by Song name
1 Press to activate search selection mode. 2 Turn the Rotary encoder to select
the SONG
search mode, then Press .
PLAYLIST ARTIST ALBUM SONG PLAYLIST
3 Turn the Rotary encoder to select the desired
Song.
4 Press MODE.
The selected song is played back.
· Press and hold for at least 2 seconds in the search mode to cancel. Or, the
search mode will be canceled when an operation has not been performed in 10
seconds.
· In the search mode, pressing FUNC. will return to the previous mode.
· Song name search cannot be made during M.I.X play.
Select Playlist/Artist/Album
Playlist/Artist/Album can be easily changed. For example, if you listen to a
song from a selected album, the album can be changed.
1 Press or to select the desired Playlist/Artist/
Album. · If search selection mode is not activated, only Song is searched,
this
operation is not possible. · If an album is selected from an artist search,
the album can be
searched. · During shuffle (M.I.X.) playback, this operation is not possible.
21-EN
Quick Search
You can search for songs.
1 Press and hold for at least 2 seconds to activate
Quick Search mode.
2 Turn the Rotary encoder to select a desired song.
The selected song is played back immediately.
· Press and hold for at least 2 seconds in the search mode to cancel. Or, the
search mode will be canceled when an operation has not been performed in 10
seconds.
· If many songs are in the iPod, it takes time to search for songs.
Random Play Shuffle (M.I.X.)
The Shuffle function of the iPod is displayed as M.I.X. on the CDE-9850Ri.
Shuffle Albums: Album shuffle playback plays back all songs in order, then randomly selects the next album. All songs of that album are played back in order, and so on. Any one album is played just once.
Shuffle Songs: Song shuffle randomly plays back certain selected songs. Any
one song plays back just once until all songs have been played back.
1 Press 5 .
The songs will be played back in random sequence.
M.I.X.
M.I.X.
(off)
(Shuffle Albums) (Shuffle Songs)
M.I.X.
2 To cancel M.I.X. play, select (off) with the above
procedure.
· For details of the search mode, refer to “Searching for a desired Song”
(page 20).
· If a song is selected in the album search mode before selecting Shuffle
(M.I.X.), the songs will not play back randomly even when Shuffle album is
selected.
Shuffle ALL: Shuffle ALL plays all songs in the iPod randomly. Any one song
does not play back again until all songs have been played back.
1 Press 6.
The songs will be played back in random sequence.
M.I.X.
(off)
(Shuffle ALL)
M.I.X.
2 To cancel M.I.X. play, select (off) with the above
procedure.
· If Shuffle All is selected, the selected ones which being played back in the search mode are cancelled.
Repeat Play
Only Repeat One is available for the iPod. Repeat One: A single song is repeatedly played back.
1 Press 4.
The file will be played repeatedly.
RPT
(off) RPT
(Repeat One)
2 To cancel repeat play, select (off) with the above
procedure.
· During repeat playback, no other songs are selectable by pressing
or
.
Displaying the Text
You can display the tag information of a song in the iPod.
Press TITLE. Each press changes the display.
TRACK NO./ELAPSED TIME ARTIST NAME ALBUM NAME SONG TITLE* TRACK NO./ELAPSED
TIME
- TAG information If the Scroll setting (page 18) is set to “SCROLL AUTO,” the tag information will scroll automatically. “ARTIST”/”ALBUM”/”SONG” is displayed if there is no tag information.
· When the Scroll Setting (page 18) is set to “SCROLL MANU,” press and hold TITLE for at least 2 seconds to scroll the tag information only once.
· Only alphanumeric characters (ASCII) can be displayed. · If the artist, album or song name, created in iTunes, has too many
characters, songs may not be played back when connected to the adapter. Therefore, a maximum of 250 characters is recommended. The maximum number of characters for the head unit is 128 (128 byte). · Some characters may not be correctly displayed. · “NO SUPPORT” is displayed when text information is not compatible with the CDE-9850Ri.
22-EN
Information
In Case of Difficulty
If you encounter a problem, please turn the power off, then on again. If the
unit is still not functioning normally, please review the items in the
following checklist. This guide will help you isolate the problem if the unit
is at fault. Otherwise, make sure the rest of your system is properly
connected or consult your authorized Alpine dealer.
Basic
No function or display. · Vehicle’s ignition is off.
– If connected following instructions, the unit will not operate with the
vehicle’s ignition off.
· Improper power lead (Red) and battery lead (Yellow) connections. – Check
power lead and battery lead connections.
· Blown fuse. – Check the fuse of the unit; replace with the proper value if
necessary.
· Internal micro-computer malfunctioned due to interference noise etc. – Press
the RESET switch with a ballpoint pen or other pointed article.
Radio
Unable to receive stations. · No antenna or open connection in cable.
– Make sure the antenna is properly connected; replace the antenna or cable if
necessary.
Unable to tune stations in the seek mode. · You are in a weak signal area.
– Make sure the tuner is in the DX mode. · If the area you are in is a primary
signal area, the antenna may
not be grounded and connected properly. – Check your antenna connections; make
sure the antenna is
properly grounded at its mounting location. · The antenna may not be the
proper length.
– Make sure the antenna is fully extended; if broken, replace the antenna with
a new one.
Broadcast is noisy. · The antenna is not the proper length.
– Extend the antenna fully; replace it if it is broken. · The antenna is
poorly grounded.
– Make sure the antenna is grounded properly at its mounting location.
CD
CD Player not functioning. · Out of operating temperature range +50°C (+120°F)
for CD.
– Allow the vehicle’s interior (or trunk) temperature to cool.
CD playback sound is wavering. · Moisture condensation in the CD Module.
– Allow enough time for the condensation to evaporate (about 1 hour).
CD insertion not possible. · A CD is already in the CD player.
– Eject the CD and remove it. · The CD is being improperly inserted.
– Make sure the CD is being inserted following instructions in the CD Player
Operation section.
Unable to fast forward or backward the CD. · The CD has been damaged.
– Eject the CD and discard it; using a damaged CD in your unit can cause
damage to the mechanism.
CD playback sound skips due to vibration. · Improper mounting of the unit.
– Securely re-mount the unit. · The disc is very dirty.
– Clean the disc. · The disc has scratches.
– Change the disc. · The pick-up lens is dirty.
– Do not use a commercial available lens cleaner disc. Consult your nearest
Alpine dealer.
CD playback sound skips without vibration. · The disc is dirty or scratched.
– Clean the disc; damaged disc should be replaced.
Error displays · Mechanical error
– Press . After the error indication disappears, insert the disc again. If the
above-mentioned solution does not solve the problem, consult your nearest
Alpine dealer.
CD-R/CD-RW playback not possible · Close session (finalization) has not been
performed.
– Perform finalization and attempt playback again.
MP3/WMA
MP3 or WMA is not played back. · Writing error occurred. The CD format is not
compatible.
– Make sure the CD has been written in a supported format. Refer to “About
MP3/WMA” (page 13-14), then rewrite in the format supported by this device.
Audio
The sound is not output from the speakers. · Unit has no output signal of the
internal amplifier.
– POWER IC is switched to “ON” (page 19).
23-EN
Indication for CD Player
· Protective circuit is activated due to high temperature. – The indication
will disappear when the temperature returns to normal operating range.
· Communication error – Turn the ignition key off, and then set to ON again. – Check the display by reconnecting between the iPod and the adapter, using the iPod cable.
· No CD is inserted. – Insert a CD.
· Although a disc is inserted, “NO DISC” is displayed and the unit does not
start to play or eject the disc. – Remove the disc by following these steps:
Press the button again for at least 2 seconds. If the disc still does not
eject, consult your Alpine dealer.
· Caused by the iPod Software Version not being compatible with the unit. – Update the iPod Software Version to be compatible with the unit.
· Mechanism error. 1) Press the button and eject the CD. If not ejecting,
consult your Alpine dealer. 2) When the error indication remains after
ejecting, press the button again. If the error indication still does not turn
off after pressing the button for a few times, consult your Alpine dealer.
· When “ERROR” is displayed: If that the disc cannot be ejected by pressing ,
press the RESET switch (refer to page 7) and press again. If the disc still
cannot be ejected, consult your Alpine dealer.
· A copy-protected WMA file was played back. – You can only play back non- copy-protected files.
· The disc is not written in a MP3/WMA supported format. – Use a disc written
at the MP3/WMA supported format.
Indication for iPod Mode
· The iPod is not connected. – Make sure the iPod is correctly connected
(refer to “Connections”). Make sure the cable is not bent excessively.
· The iPod’s battery remains low. – Refer to the iPod’s documentation and
charge the battery.
· There are no songs in the iPod. – Download songs to the iPod and connect to the adapter.
24-EN
Specifications
FM TUNER SECTION Tuning Range Mono Usable Sensitivity Alternate Channel
Selectivity Signal-to-Noise Ratio Stereo Separation Capture Ratio
MW TUNER SECTION Tuning Range Sensitivity (IEC Standard)
LW TUNER SECTION Tuning Range Sensitivity (IEC Standard)
CD SECTION Frequency Response Wow & Flutter (% WRMS) Total Harmonic Distortion
Dynamic Range Signal-to-Noise Ratio Channel Separation
PICKUP Wave length Laser power
GENERAL Power Requirement
Maximum Power Output Maximum Pre-Output Voltage Bass Treble Weight
87.5 108.0 MHz 0.7 µV 80 dB 65 dB 35 dB 2.0 dB
531 1,602 kHz 25.1 µV/28 dB
153 281 kHz 31.6 µV/30 dB
5 20,000 Hz (±1 dB) Below measurable limits 0.008% (at 1 kHz) 95 dB (at 1
kHz) 105 dB 85 dB (at 1 kHz)
795 nm CLASS I
14.4 V DC (1116 V allowable) 50 W × 4 2 V/10k ohms +20/-14dB at 60Hz ±14dB at
10kHz 1.6 kg (3 lbs. 8 oz)
CHASSIS SIZE
Width Height Depth
178 mm (7″) 50 mm (2″) 162 mm (6-3/8″)
NOSEPIECE SIZE
Width Height Depth
170 mm (6-11/16″) 46 mm (1-13/16″) 24 mm (15/16″)
· Due to continuous product improvement, specifications and design are subject to change without notice.
CAUTION
CLASS 1 LASER PRODUCT
(Bottom side of player)
25-EN
Installation and Connections
Before installing or connecting the unit, please read the following and pages
3 and 5 of this manual thoroughly for proper use.
Warning
MAKE THE CORRECT CONNECTIONS.
Failure to make the proper connections may result in fire or product damage.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may result in
fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to electrical
shorts.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other equipment. Doing so
will exceed the current carrying capacity of the wire and result in fire or
electric shock.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.
When drilling holes in the chassis for installation, take precautions so as
not to contact, damage or obstruct pipes, fuel lines, tanks or electrical
wiring. Failure to take such precautions may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND
CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any other safety-
related system), or tanks should NEVER be used for installations or ground
connections. Using such parts could disable control of the vehicle and cause
fire etc.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed, consult a
physician immediately.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE
STEERING WHEEL OR SHIFT LEVER.
Doing so may obstruct forward vision or hamper movement etc. and results in
serious accident.
Caution
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.
The wiring and installation of this unit requires special technical skill and
experience. To ensure safety, always contact the dealer where you purchased
this product to have the work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.
Be sure to use only the specified accessory parts. Use of other than
designated parts may damage this unit internally or may not securely install
the unit in place. This may cause parts to become loose resulting in hazards
or product failure.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like the seat rails) or
sharp or pointed edges. This will prevent crimping and damage to the wiring.
If wiring passes through a hole in metal, use a rubber grommet to prevent the
wire’s insulation from being cut by the metal edge of the hole.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.
Avoid installing the unit in locations with high incidence of moisture or
dust. Moisture or dust that penetrates into this unit may result in product
failure.
Precautions
· Be sure to disconnect the cable from the () battery post before installing
your CDE-9850Ri. This will reduce any chance of damage to the unit in case of
a short-circuit.
· Be sure to connect the colour coded leads according to the diagram.
Incorrect connections may cause the unit to malfunction or damage to the
vehicle’s electrical system.
· When making connections to the vehicle’s electrical system, be aware of the
factory installed components (e.g. on-board computer). Do not tap into these
leads to provide power for this unit. When connecting the CDE-9850Ri to the
fuse box, make sure the fuse for the intended circuit of the CDE-9850Ri has
the appropriate amperage. Failure to do so may result in damage to the unit
and/or the vehicle. When in doubt, consult your Alpine dealer.
· The CDE-9850Ri uses female RCA-type jacks for connection to other units
(e.g. amplifier) having RCA connectors. You may need an adaptor to connect
other units. If so, please contact your authorized Alpine dealer for
assistance.
· Be sure to connect the speaker () leads to the speaker () terminal. Never
connect left and right channel speaker cables to each other or to the vehicle
body.
IMPORTANT Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number or the engraved serial number is located on the bottom of the unit.
SERIAL NUMBER: INSTALLATION DATE: INSTALLATION TECHNICIAN: PLACE OF PURCHASE:
26-EN
Installation
Detachable Front Panel
Caution When you install this unit in your car, do not remove the detachable
front panel. If the detachable front panel is removed during installation, you
might press too hard and warp the metal plate that holds it in place.
Accessory List · Head unit ………………………………………………………………….1 · Power cable
………………………………………………………………1 · FULL SPEEDTM Connection Cable……………………………..1 ·
Mounting sleeve………………………………………………………..1 · Carrying case
……………………………………………………………1 · Rubber Cap ………………………………………………………………1 · Hex Bolt
……………………………………………………………………1 · Screw (M5 × 8)…………………………………………………………..4 ·
Owner’s Manual …………………………………………………. 1 set · The main unit must be mounted
within 35 degrees of the horizontal
plane, back to front.
Less than 35°
When your vehicle has the Bracket, mount the long hex bolt onto the rear panel
of the CDE-9850Ri and put the Rubber Cap on the hex bolt. If your vehicle does
not have the Mounting Support, reinforce the head unit with the metal mounting
strap (not supplied). Connect all the leads of the CDE-9850Ri according to
details described in the CONNECTION section. · For the screw *, provide a
proper screw to the chassis installing location.
3 Slide the CDE-9850Ri into the dashboard. When the unit is in place, make
sure the locking pins are fully seated in the down position. This can be done
by pressing firmly in on the unit while pushing the locking pin down with a
small screwdriver. This ensures that the unit is properly locked and will not
accidentally come out from the dashboard. Install the Detachable Front Panel.
Lock Pin
Removal 1. Remove the detachable front panel. 2. Use a small screwdriver (or
similar tool) to push the locking pins to the “up” position (see above
drawing). As each pin is unlocked, gently pull out on the unit to make sure it
does not re-lock before unlocking the second pin. 3. Pull the unit out,
keeping it unlocked as you do so.
1
Bracket
Rubber Cap (Included)
Hex Bolt (Included)
Dashboard
Mounting sleeve (Included)
This Unit
Slide mounting sleeve from main unit (see “Removal” on page 27). Slide the mounting sleeve into the dashboard and fix it with the metal shackles.
2
Metal Mounting Strap
Screw
Bolt Stud
Hex Nut (M5)
Face Plate
This Unit
Screws (M5 × 8) (Included)
Mounting Bracket
This Unit
27-EN
Connections
(Pink/Black) AUDIO INTERRUPT IN (Blue/White) REMOTE TURN-ON (Orange) DIMMER
(Red) IGNITION (Black) GND (Blue) POWER ANT BATTERY
(Yellow)
(Green) (Green/Black)
(White) (White/Black) (Gray/Black)
(Gray) (Violet/Black)
(Violet)
To iPod
Antenna JASO Antenna Plug
ISO Antenna Plug
To vehicle phone
To amplifier or equalizer
To the instrument cluster illumination lead
To power antenna Ignition Key
Battery
Speakers Rear Left Front Left Front Right Rear Right
28-EN
Amplifier
Speakers
Front or Subwoofers
iPod Direct Connector iPod control signals. Connect this to an iPod, using the
FULL SPEEDTM Connection Cable (supplied).
Antenna Receptacle
Audio Interrupt In Lead (Pink/Black) Connect this lead to the Audio Interface
output of a cellular phone which provides ground shorting when a call is
received.
Remote Turn-On Lead (Blue/White) Connect this lead to the remote turn-on lead
of your amplifier or signal processor.
Dimmer Lead (Orange) This lead may be connected to the vehicle’s instrument
cluster illumination lead. This will enable the vehicle’s dimmer control to
dim the backlighting of the unit.
Switched Power Lead (Ignition) (Red) Connect this lead to an open terminal on
the vehicle’s fuse box or another unused power source which provides (+) 12V
only when the ignition is turned on or in the accessory position.
Ground Lead (Black) Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is securely fastened using
the sheet metal screw provided.
Power Antenna Lead (Blue) Connect this lead to the +B terminal of your power
antenna, if applicable.
· This lead should be used only for controlling the vehicle’s power antenna.
Do not use this lead to turn on an amplifier or a signal processor, etc.
Battery Lead (Yellow) Connect this lead to the positive (+) post of the vehicle’s battery. ISO Power Supply Connector ISO Connector (Speaker Output) Left Rear (+) Speaker Output Lead (Green) Left Rear () Speaker Output Lead (Green/Black) Left Front (+) Speaker Output Lead (White) Left Front () Speaker Output Lead (White/Black) Right Front () Speaker Output Lead (Gray/Black) Right Front (+) Speaker Output Lead (Gray) Right Rear () Speaker Output Lead (Violet/Black) Right Rear (+) Speaker Output Lead (Violet) Steering Remote Control Interface Connector To steering remote control interface box. Fuse Holder (10A) Front/Subwoofer* Output RCA Connectors
- When Subwoofer is set to OFF:Output is from front speakers. When Subwoofer is set to ON:Output is from Subwoofer.
RED is right and WHITE is left. Power Supply Connector RCA Extension Cable (Sold Separately) FULL SPEEDTM Connection Cable (supplied) ISO/JASO Antenna Adaptor (Sold Separately) An ISO/JASO antenna adapter may be required, depending on the vehicle.
To prevent noise/interference in the audio system. · Locate the unit and route
the leads at least 10 cm away from the car harness. · Keep the battery power
leads as far away from other leads as possible. · Connect the ground lead
securely to a bare metal spot (remove any paint, dirt or grease if necessary)
of the car chassis. · If you add an optional noise suppressor, connect it as
far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information. · Your Alpine dealer knows
best about noise prevention measures so consult your dealer for further
information.
29-EN
ENGLISH
Contents Operating Instructions
File/Folder Name Search (concerning MP3/WMA) ………………………. 13
Quick Search …………………………………………… 13 About MP3/WMA …………………………………… 13
WARNING
WARNING …………………………………………. 3 CAUTION ………………………………………….. 3 PRECAUTIONS
…………………………………. 3
Getting Started
Turning Power On and Off …………………………. 6 Detaching and Attaching the Front Panel
…….. 6 Initial System Start-Up ………………………………. 7 Adjusting Volume
……………………………………… 7
Sound Setting
Adjusting Bass/Treble/Balance (Between Left and Right)/Fader (Between Front
and Rear)/ Defeat …………………………………………………. 15
Setting the Bass Control …………………………… 15 Setting the Treble Control ………………………….
16 Turning Loudness On/Off …………………………. 16
Other Functions
Displaying the Text ………………………………….. 16
SETUP
Radio
Listening to Radio …………………………………….. 7 Manual Storing of Station Presets
……………….. 7 Automatic Memory of Station Presets …………. 8 Tuning to Preset
Stations ……………………………. 8 Frequency Search Function ………………………… 8
RDS
Setting RDS Reception Mode and Receiving RDS Stations …………………………………………. 8
Recalling Preset RDS Stations ……………………. 9 Receiving RDS Regional (Local)
Stations ……. 9 PI SEEK Setting ……………………………………….. 9 Setting PTY31 (Emergency
Broadcast)
reception ……………………………………………….. 9 Receiving Traffic Information …………………… 10 PTY
(Programme Type) Tuning ………………… 10 Receiving Traffic Information While Playing
CD or Radio ………………………………………… 10 Priority News ………………………………………….. 11 Displaying
Radio Text ……………………………… 11
CD/MP3/WMA
Playback ………………………………………………… 11 Repeat Play …………………………………………….. 12 M.I.X.
(Random Play) ……………………………… 12 Searching from CD Text ………………………….. 12
Sound Customizing
Adjusting Source Signal Levels …………………..18 Subwoofer On and Off
……………………………….18 Setting the Subwoofer System …………………….18
Visual Customizing
Changing Lighting Colour ………………………….18 Dimmer Control ………………………………………..18
Scroll Type Setting …………………………………….18 Scroll Setting (TEXT SCROLL) ………………….18
Demonstration …………………………………………..19
MP3/WMA
Playing MP3/WMA Data (PLAY MODE) …….19
External Device
Connecting to an External Amplifier ……………19
iPodTM (Optional)
Playback …………………………………………………. 20 Searching for a desired Song …………………….. 20
Searching by Playlist …………………………….. 20 Searching by artist name ……………………….. 20
Searching by album name ……………………… 21 Searching by Song name ……………………….. 21
Select Playlist/Artist/Album ……………………… 21 Quick Search …………………………………………… 22
Random Play Shuffle (M.I.X.) …………………… 22 Repeat Play …………………………………………….. 22
Displaying the Text ………………………………….. 22
1-EN
Information
In Case of Difficulty ………………………………… 23 Specifications ………………………………………….. 25
Installation and Connections
Warning ………………………………………….. 26 Caution …………………………………………… 26 Precautions
…………………………………….. 26 Installation ……………………………………………… 27 Connections
……………………………………………. 28
2-EN
Operating Instructions
WARNING
WARNING
This symbol means important instructions. Failure to heed them can result in
serious injury or death.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING
YOUR VEHICLE.
Any function that requires your prolonged attention should only be performed
after coming to a complete stop. Always stop the vehicle in a safe location
before performing these functions. Failure to do so may result in an accident.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISE WHILE
DRIVING.
Failure to do so may result in an accident.
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric shock.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may result in
fire, etc.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed, consult a
physician immediately.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES.
Failure to do so may result in fire or electric shock.
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may result in fire.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in fire, electric shock
or other injury.
DO NOT PLACE HANDS, FINGERS OR FOREIGN OBJECTS IN INSERTION SLOTS OR GAPS.
Doing so may result in personal injury or damage to the product.
CAUTION
This symbol means important instructions. Failure to heed them can result in
injury or material property damage.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to the product. Return it
to your authorized Alpine dealer or the nearest Alpine Service Centre for
repairing.
PRECAUTIONS
Product Cleaning
Use a soft dry cloth for periodic cleaning of the product. For more severe
stains, please dampen the cloth with water only. Anything else has the chance
of dissolving the paint or damaging the plastic.
Temperature
Be sure the temperature inside the vehicle is between +60°C (+140°F) and 10°C
(+14°F) before turning your unit on.
Moisture Condensation
You may notice the CD playback sound wavering due to condensation. If this
happens, remove the disc from the player and wait about an hour for the
moisture to evaporate.
Damaged Disc
Do not attempt to play cracked, warped, or damaged discs. Playing a bad disc
could severely damage the playback mechanism.
Maintenance
If you have problems, do not attempt to repair the unit yourself. Return it to
your Alpine dealer or the nearest Alpine Service Station for servicing.
3-EN
Never Attempt the Following
Do not grip or pull out the disc while it is being pulled back into the player
by the automatic reloading mechanism. Do not attempt to insert a disc into the
unit when the unit power is off.
Inserting Discs
Your player accepts only one disc at a time for playback. Do not attempt to
load more than one disc. Make sure the label side is facing up when you insert
the disc. “ERROR” will be displayed on your player if you insert a disc
incorrectly. If “ERROR” continues to be displayed even though the disc has
been inserted correctly, push the RESET switch with a pointed object such as a
ballpoint pen. Playing a disc while driving on a very bumpy road may result in
skips, but this will not scratch the disc or damage the player.
New Discs
To prevent the CD from jamming, “ERROR” is displayed if discs with irregular
surfaces are inserted or if discs are inserted incorrectly. When a new disc is
ejected immediately after initial loading, use your finger to feel around the
inside of the center hole and outside edge of the disc. If you feel any small
bumps or irregularities, this could inhibit proper loading of the disc. To
remove the bumps, rub the inside edge of the hole and outside edge of the disc
with a ballpoint pen or other such instrument, then insert the disc again.
Centre Hole Centre Hole
New Disc
Bumps
Outside (Bumps)
Irregular Shaped Discs
Be sure to use round shape discs only for this unit and never use any special
shape discs. Use of special shape discs may cause damage to the mechanism.
Installation Location
Make sure the CDE-9850Ri will not be installed in a location subjected to:
· Direct sun and heat · High humidity and water · Excessive dust · Excessive
vibrations
Correct Handling
Do not drop the disc while handling. Hold the disc so you will not leave
fingerprints on the surface. Do not affix tape, paper, or gummed labels to the
disc. Do not write on the disc.
CORRECT
INCORRECT
CORRECT
Disc Cleaning
Fingerprints, dust, or soil on the surface of the disc could cause the CD
player to skip. For routine cleaning, wipe the playing surface with a clean,
soft cloth from the centre of the disc to the outer edge. If the surface is
heavily soiled, dampen a clean, soft cloth in a solution of mild neutral
detergent before cleaning the disc.
Disc Accessories
There are various accessories available on the market for protecting the disc
surface and improving sound quality. However, most of them will influence the
thickness and/or diameter of the disc. Using such accessories can cause the
disc to be out of standard specifications and may create operational problems.
We recommend not using these accessories on discs played in Alpine CD players.
Transparent Sheet
Disc Stabilizer
4-EN
On handling Compact Discs (CD/CD-R/CD-RW)
· Do not touch the surface. · Do not expose the disc to direct sunlight. · Do
not affix stickers or labels. · Clean the disc when it is dusty. · Make sure
that there are no bumps around the disc. · Do not use commercially available
disc accessories. Do not leave the disc in the car or the unit for a long
time. Never expose the disc to direct sunlight. Heat and humidity may damage
the CD and you may not be able to play it again.
To customers using CD-R/CD-RW
· If a CD-R/CD-RW cannot be played back, make sure the last recording session
was closed (finalized).
· Finalize the CD-R/CD-RW if necessary, and attempt playback again.
About media that can be played.
Use only compact discs with the label side showing the CD logo marks below.
If you use unspecified compact discs, correct performance cannot be
guaranteed. You can play CD-Rs (CD-Recordable)/CD-RWs (CD-ReWritable) which
have been recorded only on audio devices. You can also play CD-Rs/CD-RWs
containing MP3/WMA formatted audio files. · Some of the following CDs may not
play on this unit:
Flawed CDs, CDs with fingerprints, CDs exposed to extreme temperatures or
sunlight (e.g., left in the car or this unit), CDs recorded under unstable
conditions, CDs on which a recording failed or a re-recording was attempted,
copy-protected CDs which do not conform to the audio CD industry standard. ·
Use discs with MP3/WMA files written in a format compatible with this unit.
For details, see pages 13-14. · ROM data other than audio files contained in a
disc will not produce sound when played back.
· Windows Media and the Windows logo are trademarks, or registered trademarks
of Microsoft Corporation in the United States and /or other countries.
· Apple, the Apple logo and iPod are trademarks of Apple Computer, Inc.,
registered in the U.S. and other countries.
· “MPEG Layer-3 audio coding technology licensed from Fraunhofer llS and
Thomson.”
· “Supply of this product only conveys a license for private, noncommercial
use and does not convey a license nor imply any right to use this product in
any commercial (i.e. revenuegeneration) real time broadcasting (terrestrial,
satellite, cable and/or any other media), broadcasting/streaming via internet,
intranets and/or other networks or in other electronic content distribution
systems, such as pay-audio or audio-on-demand applications. An independent
license for such use is required. For details, please visit http://www.
mp3licensing.com.”
5-EN
Getting Started
(OPEN)
SOURCE/ POWER Rotary encoder
To close the front panel, press the left side until it locks as shown in the figure below.
3 Grasp the front panel firmly, slide to the left
pull to remove.
, then
Turning Power On and Off
Press SOURCE/POWER to turn on the unit. · The unit can be turned on by
pressing any other button except
(OPEN) and Rotary encoder. Press and hold SOURCE/POWER for at least 2 seconds
to turn off the unit. · The first time power is turned on, the volume will
start from level 12.
Detaching and Attaching the Front Panel
Be sure to push the Rotary encoder inside the unit before opening the front
panel so that the front panel will open completely, otherwise it may be
damaged.
Push the Rotary encoder inside When you push the Rotary encoder again, it pops
back out.
· The front panel may become hot in normal usage (especially the connector
terminals on the back of the front panel.) This is not a malfunction.
· To protect the front panel, place it in the supplied carrying case. · When
detaching the front panel, do not apply excessive force as it
may result in malfunction. · Do not leave the front panel open, or drive the
car with the panel
open as it may result in accident or malfunction.
Attaching
1 Insert the right side of the front panel into the main
unit. Align the groove on the front panel with the projections on the main
unit.
2 Push the left side of the front panel until it locks
firmly into the main unit.
The Rotary encoder pops out
Detaching
1 Turn off the unit power. 2 Press (OPEN) to open the front panel.
· Before attaching the front panel, make sure that there is no dirt or dust on
the connector terminals and no foreign object between the front panel and the
main unit.
· Attach the front panel carefully, holding the sides of the front panel to
avoid pushing buttons by mistake.
6-EN
Initial System Start-Up
Be sure to press the RESET switch when using the unit for the first time,
after changing the car battery, etc.
1 Turn off the unit power. 2 Press (OPEN) to open the front panel, then
remove it.
3 Press RESET with a ballpoint pen or similar pointed
object.
Radio
Rotary SOURCE/POWER
encoder
BAND
TUNE/A.ME
MODE
FUNC. Preset buttons (1 through 6)
RESET switch
Adjusting Volume
Turn the Rotary encoder until the desired sound is obtained.
Controllable With Remote Control The CDE-9850Ri can be controlled with an
optional Alpine remote control. For details, consult your Alpine dealer. Point
the optional remote control transmitter at the remote control sensor. Remote
control sensor
Connectable to Remote Control Interface Box You can operate this unit from the
vehicle’s control unit when an Alpine Remote Control Interface Box (optional)
is connected. For details, contact your Alpine dealer.
Listening to Radio
1 Press SOURCE/POWER until a radio frequency
appears on the display.
2 Press BAND repeatedly until the desired radio band
is displayed.
F1 (FM1) F2 (FM2) F3 (FM3) MW LW F1 (FM1)
3 Press TUNE/A.ME to select the tuning mode.
DX SEEK (Distance mode) SEEK (Local mode) OFF (Manual mode) DX SEEK
· The initial mode is Distance mode.
Distance mode: Both strong and weak stations will be automatically tuned in (Automatic Seek Tuning).
Local mode: Only strong stations will be automatically tuned in (Automatic Seek Tuning).
Manual mode: The frequency is manually tuned in steps (Manual tuning).
4 Press
or
Holding down
continuously.
to tune in the desired station.
or
will change the frequency
Manual Storing of Station Presets
1 Select the radio band and tune in a desired radio
station you wish to store in the preset memory.
2 Press and hold, for at least 2 seconds, any one of the
preset buttons (1 through 6) into which you wish to store the station. The
selected station is stored. The display shows the band, preset number and
station frequency memorized.
7-EN
· A total of 30 stations can be stored in the preset memory (6 stations for
each band; FM1, FM2, FM3, MW and LW).
· If you store a station in a preset memory which already has a station, the
current station will be cleared and replaced with the new station.
· If the “FUNC” indicator is illuminated, turn off the indicator by pressing
FUNC., then you can perform the operation.
Automatic Memory of Station Presets
1 Press BAND repeatedly until the desired radio band
is displayed.
2 Press and hold TUNE/A.ME for at least 2 seconds.
The frequency on the display continues to change while the automatic memory is
in progress. The tuner will automatically seek and store 6 strong stations in
the selected band. They will be stored into buttons 1 to 6 in order of signal
strength. When the automatic memory has been completed, the tuner goes to the
station stored in preset location No.1.
· If no stations are stored, the tuner will return to the original station you
were listening to before the auto memory procedure began.
Tuning to Preset Stations
1 Press BAND repeatedly until the desired band is
displayed.
2 Press any one of the station preset buttons (1
through 6) that has your desired radio station in memory. The display shows
the band, preset number and frequency of the station selected.
· If the “FUNC” indicator is illuminated, turn off the indicator by pressing
FUNC., then you can perform the operation.
Frequency Search Function
You can search for a radio station by its frequency.
1 Press and hold for at least 2 seconds in Radio
mode to activate Frequency Search mode.
2 Turn the Rotary encoder to select the desired
frequency.
3 Press MODE to receive the selected frequency.
· Press and hold for at least 2 seconds in the search mode to cancel. Or, the
search mode will be cancelled when an operation has not been performed in 10
seconds.
RDS
Rotary TA encoder
MENU FUNC.
MODE
1 AF NEWS 2 3 PTY TITLE
Setting RDS Reception Mode and Receiving RDS Stations
The RDS (Radio Data System) is a radio information system using the 57 kHz subcarrier of regular FM broadcast. The RDS allows you to receive a variety of information such as traffic information, station names, and to automatically re-tune to a stronger transmitter that is broadcasting the same programme.
1 Press FUNC. so that the “FUNC” indicator lights up.
2 Press 1 AF to activate the RDS mode.
3 Press
or
station.
to tune in the desired RDS
4 Press 1 AF again to deactivate the RDS mode.
5 Press FUNC. to activate the normal mode.
The “FUNC” indicator goes out.
· When the “Setting PTY31 (Emergency Broadcast) reception” (refer to page 9) is set to on, if the unit receives the PTY31 (Emergency Broadcast) signal, the unit will show “ALARM” in the display automatically.
The RDS digital data includes the following:
PI
Programme Identification
PS Programme Service Name
AF List of Alternative Frequencies
TP
Traffic Programme
TA
Traffic Announcement
PTY Programme Type
EON Enhanced Other Networks
8-EN
Recalling Preset RDS Stations
1 Press FUNC. so that the “FUNC” indicator lights up.
2 Press 1 AF to activate the RDS mode.
3 Press FUNC. to activate the normal mode.
The “FUNC” indicator goes out.
4 Make sure that the “FUNC” indicator light goes out,
then press the preset button in which your desired RDS station is preset. If
the preset station’s signal is weak, the unit automatically searches and tunes
to a stronger station in the AF (Alternative Frequencies) list.
5 If the preset station and the stations in the AF list
cannot be received: When the PI SEEK setting is on (refer to “PI SEEK Setting”
on page 9), the unit searches again for a station in the PI (Programme
Identification) list. If there are still no stations receivable in the area,
the unit displays the frequency of the preset station and the preset number
disappears. If the signal level of the Regional (Local) station being tuned
becomes too weak to receive, press the same preset button to tune in a
Regional station in other district.
· For presetting the RDS stations, refer to the Radio Operation section. The
RDS stations can be preset in the F1, F2 and F3 bands only.
Receiving RDS Regional (Local) Stations
1 Press MENU to select the SETUP mode, then press
MODE.
SETUP mode is activated.
BASS ENGINE SETUP RETURN (OFF) BASS ENGINE
2 Press
or
to select the RDS REGIONAL
mode, then press MODE.
3 Turn the Rotary encoder to select ON or OFF.
In the OFF mode, the unit automatically keeps receiving the related local RDS
station.
4 Press MENU to select RETURN.
After 2 seconds, the unit returns to normal mode. Pressing and holding MENU
for at least 2 seconds will return to normal mode.
PI SEEK Setting
1 Press MENU to select the SETUP mode, then press
MODE. SETUP mode is activated.
BASS ENGINE SETUP RETURN (OFF) BASS ENGINE
2 Press
or
MODE.
to select the PI SEEK, then press
3 Turn the Rotary encoder to select ON or OFF.
4 Press MENU to select RETURN.
After 2 seconds, the unit returns to normal mode. Pressing and holding MENU
for at least 2 seconds will return to normal mode.
Setting PTY31 (Emergency Broadcast) reception
Turn PTY31 (Emergency Broadcast) reception ON/OFF.
1 Press MENU to select SETUP mode, then press
MODE. The SETUP mode is activated.
BASS ENGINE SETUP RETURN (OFF) BASS ENGINE
2 Press
or
to the select ALERT PTY31
mode, then press MODE.
3 Turn the Rotary encoder to select ON or OFF.
If you set ON, emergency broadcast are received regardless of source. “ALARM”
is displayed during reception.
4 Press MENU to select RETURN.
After 2 seconds, the unit returns to normal mode. Pressing and holding MENU
for at least 2 seconds will return to normal mode. When an emergency broadcast
is received, the volume level will be automatically changed to the memorized
level in the traffic information mode. For details, refer to “Receiving
Traffic Information.”
9-EN
Receiving Traffic Information
1 Press TA so that the “TA” indicator lights up.
2 Press
or
to select your desired traffic
information station.
When a traffic information station is tuned in, the “TP” indicator lights up. Traffic information is heard only when it is being broadcast. If traffic information is not being broadcast, the unit is set in the standby mode. When a traffic information broadcast begins, the unit automatically receives it and the display shows “TRF-INFO” for a few seconds. When the traffic information broadcast is over, the unit will automatically set in the standby mode.
· If the traffic information broadcast signal falls below a certain level, the
unit remains in the receiving mode for 1 minute. If the signal remains below a
certain level for over 1 minute, the “TA” indicator blinks.
· If you do not want to listen to the traffic information being received,
lightly press TA to skip that traffic information message. The TA mode will
remain in the ON position to receive the next traffic information message.
· If the volume level is changed while receiving traffic information, the
changed volume level will be memorized. When traffic information is received
next time, the volume level will be automatically adjusted to the level
memorized.
· In the TA mode, the SEEK tuning selects only the TP stations.
PTY (Programme Type) Tuning
1 Press FUNC. so that the “FUNC” indicator lights up.
2 Press 3 PTY to activate the PTY mode, while the
unit is in Radio (FM receiving) mode. The Programme Type of the station being
currently received will be displayed for 10 seconds. If there is no receivable
PTY broadcast, “NO PTY” will be displayed for 10 seconds. If no RDS station
can be received, the display shows “NO PTY.”
· If no operation is performed within 10 seconds after pressing 3 PTY, the PTY mode will be automatically cancelled.
3 Press
or
within 10 seconds after
activating the PTY mode to choose the desired
programme type while the PTY (programme type) is
being displayed.
Each press scrolls the programme type by one.
LIGHT M CLASSICS OTHER M
5 Press FUNC. to activate the normal mode.
The “FUNC” indicator goes out.
· Operate the unit while the “FUNC” indicator lights up. If no operation is
performed within 10 seconds, the “FUNC” indicator goes out.
Receiving Traffic Information While Playing CD or Radio
1 Press TA so that the “TA” indicator lights up.
2 Press
or
to select a traffic information
station if necessary.
When a traffic information broadcast starts, the unit automatically mutes the CD player or the regular FM broadcast. When the traffic information broadcast finishes, the unit automatically returns to the original source play before the traffic information broadcast began.
When traffic information stations cannot be received: In the tuner mode: When the TP signal can no longer be received for over 1 minute, the “TA” indicator blinks.
In the CD mode: When the TP signal can no longer be received, the traffic information station of another frequency will be selected automatically.
· The receiver is equipped with the EON (Enhanced Other Networks) function in
order to keep track of additional alternate frequencies to the AF list. The
“EON” indicator lights up while an RDS EON station is being received. If the
station being received does not broadcast the traffic information, the
receiver automatically tunes in the related station that broadcasts the
traffic information when it occurs.
3 Press TA to deactivate the Traffic Information mode.
The “TA” indicator goes out.
4 Press 3 PTY within 10 seconds after selecting the
programme type to start searching for a station in the selected programme
type. The chosen programme type display blinks during searching and lights
when a station is found.
If no PTY station is found, “NO PTY” will be displayed for 10 seconds.
10-EN
Priority News
This function allows you to preset to give priority to the News programme. You
will never miss the News programme as the unit automatically gives priority to
the News programme whenever it begins broadcasting, and interrupts the
programme you are currently listening. This feature is functional when your
unit is set to a mode other than the MW and LW modes.
1 Press FUNC. so that the “FUNC” indicator lights up
while the unit is in Radio (FM receiving) mode.
2 Press NEWS 2 to activate the PRIORITY NEWS
mode. The “NEWS” indicator appears in the display. To disable the PRIORITY
NEWS function, press NEWS 2.
· In the PRIORITY NEWS function, unlike in the TA function, the volume does
not increase automatically.
3 Press FUNC. to activate the normal mode, while the
unit is in Radio (FM receiving) mode. The “FUNC” indicator light goes out.
Displaying Radio Text
Text messages from a radio station can be displayed.
Press TITLE while receiving FM in the radio mode to select the Radio Text
display.
The display will change every time the button is pressed.
If there is PS (Programme Service NAME): PS (Programme Service Name)* Radio
Text PS (Programme Service Name)
- Press and hold TITLE for at least 2 seconds if PS is displayed in the radio mode, “FREQUENCY” will be displayed for 5 seconds.
If there is no PS (Programme Service Name): FREQUENCY Radio Text FREQUENCY
The display shows “WAITING” for a few seconds, then starts scrolling the text message.
· If there is no receivable text message or the unit cannot receive a text message properly, the display shows “NO TEXT.”
CD/MP3/WMA
(OPEN)
Rotary SOURCE/POWER
encoder
/
MODE
FUNC.
45
TITLE
Playback
1 Press (OPEN).
The front panel will open.
2 Insert a disc with the label side facing up.
The disc will be pulled into the unit automatically.
Close the front panel manually. When a disc is already inserted, press SOURCE/POWER to switch to the CD mode.
The mode will change every time the button is pressed.
TUNER DISC IPOD* TUNER
- Only when the iPod is connected.
3 While playing back MP3/WMA, press or to
select the desired folder. Pressing and holding or will change folders
continuously.
4 Press
or
to select the desired track (file).
Returning to the beginning of the current track (file):
Press
.
Fast backward:
Press and hold
.
Advancing to the beginning of the next track (file):
Press
.
Fast forward:
Press and hold
.
5 To pause playback, press / .
Pressing / again will resume playback.
11-EN
6 After pressing (OPEN) to open the front panel,
press to eject the disc.
· Do not remove a CD during its eject cycle. Do not load more than one disc at
a time. A malfunction may result from doing either.
· If the CD does not eject, press and hold for at least 2 seconds. · The CD-
player can play discs containing audio data, MP3 data and
WMA data. · A WMA format file that is protected by DRM (Digital Rights
Management) cannot be played back on this unit. · The track display for
MP3/WMA data playback is the file numbers
recorded on the disc. · The playback time may not be correctly displayed when
a VBR
(Variable Bit Rate) recorded file is played back.
MP3/WMA Play Display The folder number and file number will be displayed as
described below.
F01 T03 10’15
Folder number File number Elapsed time
display
display
· Press TITLE to switch the display. See “Displaying the Text” (page 16) for
information about display switching.
· If the folder number or file number is 3 digits, F or T becomes numbers of
hundred rank.
Repeat Play
Press 4 to play back repeatedly the track being played. The track (file) will
be played repeatedly. Press 4 again and select off to deactivate repeat play.
CD mode :
: Only a track is repeatedly played back.
MP3/WMA mode :
M.I.X. (Random Play)
Press 5 in the play or pause mode. The tracks (files) on the disc will be
played back in random sequence. To cancel M.I.X. play, press 5 again. CD mode
:
: The tracks are played back in random sequence.
MP3/WMA mode :
: Only files in a folder are played back in random sequence.
: The files are played back in random sequence.
Searching from CD Text
Tracks can be searched and played by using the CD text on the disc. In the
case of discs that do not support text, searches can be made by using the
track numbers.
1 Press during play.
This will set the search mode.
2 Turn the Rotary encoder to select the desired
track, then press MODE. This will play the selected track. · Press and hold
for at least 2 seconds in the search mode to cancel. Or, the search mode will
be cancelled when an operation has not been performed in 10 seconds. · CD text
search cannot be made during M.I.X. play.
: Only a file is repeatedly played back. : Only files in a folder are repeatedly played back.
12-EN
File/Folder Name Search (concerning MP3/WMA)
You can display and search the folder and file name while listening to the
file currently being played back.
1 Press to activate Search selection mode during
MP3/WMA playback.
2 Turn the Rotary encoder to select Folder Name
Search mode or File Name Search mode, then press .
Quick Search
You can search for tracks (files).
1 Press and hold for at least 2 seconds in the CD/
MP3/WMA mode to activate Quick Search mode.
2 Turn the Rotary encoder to select a desired track
(file). The selected track is played back immediately.
· Press and hold for at least 2 seconds in the search mode to cancel. Or, the
search mode will be cancelled when an operation has not been performed in 10
seconds.
Folder Name Search mode
3 Turn the Rotary encoder to select the desired
folder.
4 Press / to play back the first file in the selected
folder.
· Press and hold for at least 2 seconds in the search mode to cancel. Or, the
search mode will be cancelled when an operation has not been performed in 10
seconds.
· While in Folder Name Search mode, press to switch to File Name Search mode.
· “ROOT” is displayed for the root folder which does not have folder name.
· Folder Name search cannot be made during M.I.X. play. · Press FUNC. in the
Search mode to return to the previous step. · Folder search cannot be
performed if the disc only has root folder. · If there is no file in the
folder when selecting the folder search mode,
“NO FILE” will be displayed for 2 seconds.
File Name Search mode
3 Press or to select another Folder.
4 Select the desired file by turning the Rotary
encoder.
5 Press MODE to playback the selected file.
· Press and hold for at least 2 seconds in the search mode to cancel. Or, the
search mode will be cancelled when an operation has not been performed in 10
seconds.
· File Name search cannot be made during M.I.X. play. · Press FUNC. in the
Search mode to return to the previous step.
About MP3/WMA
CAUTION Except for private use, duplicating audio data (including MP3/ WMA
data) or distributing, transferring, or copying it, whether for free or for a
fee, without permission of the copyright holder is strictly prohibited by the
Copyright Act and by international treaty.
What is MP3?
MP3, whose official name is “MPEG-1 Audio Layer 3,” is a compression standard
prescribed by the ISO, the International Standardization Organization and MPEG
which is a joint activity institution of the IEC.
MP3 files contain compressed audio data. MP3 encoding is capable of
compressing audio data at extremely high ratios, reducing the size of music
files to as much as one-tenth their original size. This is achieved while
still maintaining near CD quality. The MP3 format realizes such high
compression ratios by eliminating the sounds that are either inaudible to the
human ear or masked by other sounds.
What is WMA?
WMA, or “Windows MediaTM Audio,” is compressed audio data. WMA is similar to
MP3 audio data and can achieve CD quality sound with small file sizes.
Method for creating MP3/WMA files
Audio data is compressed by using MP3/WMA specified software. For details on
creating MP3/WMA files, refer to the user’s manual for that software. MP3/WMA
files that can be played back by this device have the file extension “mp3” /
“wma”. Files with no extension cannot be played back. (WMA ver. 7.1, 8 and 9
are supported)
13-EN
Supported playback sampling rates and bit rates
MP3
Sampling rates: 48 kHz, 44.1 kHz, 32 kHz, 24 kHz, 22.05 kHz,
16 kHz, 12 kHz, 11.025 kHz, 8 kHz
Bit rates:
8 – 320 kbps
WMA
Sampling rates: 48 kHz, 44.1 kHz, 32 kHz
Bit rates:
48 – 192 kbps
Note that for sampling rates, this device’s frame display (page 16) may not display correctly. This device may not play back correctly depending on sampling rates.
ID3 tags/WMA tags
This device supports ID3 tag v1 and v2, and WMA tag. If tag data is in an
MP3/WMA file, this device can display the title (track title), artist name,
and album name ID3 tag/WMA tag data.
This device can only display single-byte alphanumeric characters (up to 30 for
ID3 tags and up to 15 for WMA tags) and the underscore. For non-supported
characters, “NO SUPPORT” is displayed. The tag information may not be
correctly displayed, depending on the contents.
Producing MP3/WMA discs
MP3/WMA files are prepared, then written to a CD-R or CD-RW using CD-R writing
software. A disc can hold up to 510 files/ folders (including Root Folders).
However, the maximum number of folders is 255.
Media supported
The media that this device can play back are CD-ROMs, CD-Rs, and CD-RWs.
Corresponding File Systems
This device supports discs formatted with ISO9660 Level 1 or Level 2.
Under the ISO9660 standard, there are some restrictions to remember. The
maximum nested folder depth is 8 (including the root directory). The number of
characters for a folder/file name is limited. Valid characters for folder/file
names are letters A-Z (all caps), numbers 0-9, and `_’ (underscore).
This device also can play back discs in Joliet, Romeo, etc., and other
standards that conform to ISO9660. However, sometimes the file names, folder
names, etc., are not displayed correctly.
Formats supported
This device supports CD-ROM XA, Mixed Mode CD, Enhanced CD (CD-Extra) and
Multi-Session. This device cannot correctly play back discs recorded with
Track At Once or packet writing.
Order of files The unit plays the files in the order that the writing software
writes them. Therefore, the playing order may not be the same as the order you
input. The playback order of the folders and files is as follows. However, the
folder and file playback order differs from the folder and file number
indicated on the display.
Root folder
Folder
MP3/WMA File
Terminology
Bit rate This is the “sound” compression rate specified for encoding. The
higher the bit rate, the higher the sound quality, but also the larger the
files.
Sampling rate This value shows how many times per second the data is sampled
(recorded). For example, music CDs use a sampling rate of 44.1 kHz, so the
sound is sampled (recorded) 44,100 times per second. The higher the sampling
rate, the higher the sound quality, but also the larger the volume of data.
Encoding Converting music CDs, WAVE (AIFF) files, and other sound files into
the specified audio compression format.
Tag Song information such as track titles, artist names, album names, etc.,
written into MP3/WMA files. MP3: ID3 tag WMA: WMA tag
Root folder The root folder is found at the top of the file system. The root
folder contains all folders and files.
14-EN
Sound Setting
Rotary encoder SOURCE/POWER BAND MENU
Setting the Bass Centre Frequency
3-1 Press SOURCE/POWER to select the desired bass
centre frequency.
80Hz 100Hz 120Hz 60Hz 80Hz Emphasize the displayed bass frequency ranges.
Setting the Bass Bandwidth
3-2 Press BAND to select the desired bass bandwidth.
MODE
Adjusting Bass/Treble/Balance (Between Left and Right)/Fader (Between Front
and Rear)/Defeat
1 Press MODE repeatedly to choose the desired
mode.
Each press changes the mode as follows:
BASS TREBLE SUBW* BALANCE FADER DEFEAT VOLUME BASS
Bass Level: 7 ~ +10 Treble Level: 7 ~ +7 Subwoofer : 0 ~ +15 Balance : L15 ~
R15 Fader : R15 ~ F15 Defeat : ON/OFF Volume : 0 ~ 35
· If MODE is not pressed within 5 seconds after selecting the BASS, TREBLE,
BALANCE, FADER, DEFEAT or SUBW mode, the unit automatically returns to normal
mode.
- When the subwoofer mode is set to OFF, its level cannot be adjusted.
2 Turn the Rotary encoder until the desired sound is
obtained in each mode. By setting Defeat ON, previously adjusted settings of BASS and TREBLE will return to the factory defaults.
Setting the Bass Control
You can change the Bass Frequency emphasis to create your own tonal
preference.
1 Press MENU to select the BASS ENGINE mode, then
press MODE.
BASS ENGINE SETUP RETURN (OFF) BASS ENGINE
2 Press
or
to select the BASS (bass Centre
frequency) control mode.
BASS TREBLE
Change the boosted bass bandwidth to wide or narrow. A wide setting will boost a wide range of frequencies above and below the centre frequency. A narrower setting will boost only frequencies near the centre frequency.
Setting the Bass Level
3-3*1Turn the Rotary encoder to select the desired
bass level (7~+10). You can emphasize or weaken the bass level.
4 Press MENU to select RETURN.
After 2 seconds, the unit returns to normal mode. Pressing and holding MENU
for at least 2 seconds will return to normal mode.
· If no operation is performed within 60 seconds, the bass control
setting will be turned off automatically.
· The bass level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
bass frequency and bass band width settings adjusted for one source
are effective for all other sources (FM, MW (LW), CD etc.).
· Depending on the connected devices, some functions and display
indications do not work. However, Bass Level is still adjustable if an
audio processor with the Bass function is connected.
· This function is inoperable when DEFEAT is set to ON.
· If you press
or
in the bass control mode, the unit
changes to the treble control mode. *1 The adjustment can also be made by pressing MODE. Refer to
“Adjusting Bass/Treble/Balance (Between Left and Right)/Fader
(Between Front and Rear)/Defeat” (page 15).
Bass level indicator’s display
Bass level is usually displayed.
15-EN
Setting the Treble Control
You can change the Treble Frequency emphasis to create your own tonal
preference.
1 Press MENU to select the BASS ENGINE mode, then
press MODE.
BASS ENGINE SETUP RETURN (OFF) BASS ENGINE
2 Press
or
to select the TREBLE (Treble
Centre Frequency) control mode.
BASS TREBLE
Setting the Treble Centre Frequency
3-1 Press SOURCE/POWER to select the desired treble
Centre frequency.
10.0kHz 12.5kHz 15.0kHz 7.5kHz 10.0kHz Emphasize the displayed treble
frequency ranges.
Setting the Treble Level
3-2*2Turn the Rotary encoder to select the desired
treble level (7~+7). You can emphasize the treble level.
4 Press MENU to select RETURN.
After 2 seconds, the unit returns to normal mode. Pressing and holding MENU
for at least 2 seconds will return to normal mode.
· If no operation is performed within 60 seconds, the treble control
setting will be turned off automatically.
· The treble level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
Treble frequency settings adjusted for one source are effective for all
other sources (FM, MW (LW), CD, etc.).
· Depending on the connected devices, some functions and display
indications do not work. However, Treble Level is still adjustable if
an audio processor with the Treble function is connected.
· This function is inoperable when DEFEAT is set to ON.
· If you press
or
in the treble control mode, the unit
changes to the bass control mode. *2 The adjustment can also be made by pressing MODE. Refer to
“Adjusting Bass/Treble/Balance (Between Left and Right)/Fader
(Between Front and Rear)/Defeat” (page 15).
Turning Loudness On/Off
Loudness introduces a special low- and high-frequency emphasis at low
listening levels. This compensates for the ear’s decreased sensitivity to bass
and treble sound.
Press and hold MODE for at least 2 seconds to activate or deactivate the
loudness mode. “LD” indicator lights.
Other Functions
TITLE
Displaying the Text
Text information, such as the disc name and the track name, will be displayed
if playing a CD text compatible disc. It is also possible to display the
folder name, the file name, and the tag, etc., while playing MP3/WMA files.
Press TITLE. The display will change every time the button is pressed.
The display in Radio mode: If there is PS (Programme Service NAME)
PS (Programme Service Name)1 Radio Text PS (Programme Service Name) If there
is no PS (Programme Service Name) FREQUENCY Radio Text FREQUENCY The display
in CD mode: TRACK NO./ELAPSED TIME TEXT (DISC NAME)2 TEXT (TRACK NAME)2
TRACK NO./ELAPSED TIME The display in MP3/WMA mode: FOLDER NO./FILE
NO./ELAPSED TIME FOLDER NAME3 FILE NAME3 ARTIST NAME4 ALBUM NAME4 TRACK
NAME4 FRAME5 FOLDER NO./FILE NO./ELAPSED TIME 1 Press and hold TITLE for at
least 2 seconds in the PS display mode, “FREQUENCY” will be displayed for 5
seconds. 2 Displayed during playback of a disc with CD Text. If there is no
Text (Disc Name or Track Name), “DISC TEXT”/ “TRACK TEXT” is displayed. 3
“ROOT” is displayed for the folder name of the root folder which does not have
folder name. If there is no folder name or file name, “FOLDER”/”FILE” is
displayed. 4 ID3 tag/WMA tag If an MP3/WMA file contains ID3 tag/WMA tag
information, the ID3 tag/WMA tag information is displayed (track name, artist
name, and album name). All other tag data is ignored. If there is no tag
information, “ARTIST”/”ALBUM”/”SONG” will be displayed. If “SCROLL AUTO” is
set in “Scroll Setting (TEXT SCROLL)” (page 18), tag information will
automatically be scrolled. 5 The recording sampling rate and bit rate of the
MP3/WMA file are displayed. A WMA file of variable bit rate displays the
average bit rate.
16-EN
About the indication display
When displaying Text, the following indicators are lit according to the mode.
The position of a song being played back is shown lit in the total number of
songs shown. The display example is as shown below. Also lights when operation
,such as fast forward, etc.,is performed. Lights up when a disc is inserted
Song position display example
· For example, when the 5th of 10 songs in the disc is played back,
”
” is displayed.
Indicator/ Mode
CD Mode
MP3/WMA Mode
iPod Mode
While
—
displaying
—
Folder Name
While
—
displaying
—
File Name
While
While
—
displaying
displaying
Artist Name Artist Name
While displaying Text (Disc Name)
While displaying Album Name*
While displaying Album Name*
While displaying Text (Track Name)
While displaying Track Name*
While displaying Track Name*
*Tag information
About “Text”
Text: Text compatible CDs contain text information such as the disc name and
track name. Such text information is referred to as “text.”
· Some characters may not be displayed correctly with this device, depending
on the character type.
· When the Scroll Setting (page 18) is set to “SCROLL MANU,” press and hold
TITLE for at least 2 seconds to scroll the Text information only once (TEXT
DISPLAY, FOLDER NAME DISPLAY, FILE NAME DISPLAY or TAG DISPLAY mode).
· “NO SUPPORT” is displayed when the desired text information cannot be
displayed on this unit.
· The text or tag information may not be correctly displayed, depending on the
contents.
17-EN
SETUP
You can flexibly customize the unit to suit your own preferences and usage.
Choose the SETUP menu from Sound Customizing, Visual Customizing, etc., to
select your desired setting.
Rotary encoder MENU
MODE
A typical SETUP procedure is shown in steps 1 to 4 as follows. See below for further information about each SETUP menu.
1 Press MENU to select the SETUP mode, then press
MODE.
BASS ENGINE SETUP RETURN (OFF) BASS ENGINE
2 Press
or
to select the desired SETUP
menu, then press MODE.
(e.g. Select SUBWOOFER)
FM LEVEL RDS REGIONAL1 PI SEEK2 ALERT PTY313 ILLUMINATION DIMMER SUBWOOFER
(SUBW SYSTEM)4 PLAY MODE
SCROLL TYPE TEXT SCROLL POWER IC DEMO
FM LEVEL
1 Refer to “Receiving RDS Regional (Local) Stations” (page 9) 2 Refer to “PI SEEK Setting” (page 9) 3 Refer to “Setting PTY31 (Emergency Broadcast) reception” (page 9) 4 Displayed only when SUBW is ON.
3 Turn the Rotary encoder to change the setting.
(e.g. Select SUBW ON or SUBW OFF.)
4 Press MENU to select RETURN.
After 2 seconds, the unit returns to normal mode. Pressing and holding MENU
for at least 2 seconds will return to normal mode.
Sound Customizing
Adjusting Source Signal Levels
FM-LEVEL HI (Initial setting) / FM-LEVEL LOW
If the difference in volume level between the CD player and FM radio is too
great, adjust the FM signal level.
Subwoofer On and Off
SUBW ON (Initial setting) / SUBW OFF
When the subwoofer is on, perform the steps below to adjust the subwoofer
output level.
1 In the normal mode, press MODE repeatedly to select the SUBW mode.
BASS TREBLE SUBW BALANCE FADER DEFEAT VOLUME BASS 2 Adjust the level by
turning the Rotary encoder.
Setting the Subwoofer System
SUBW SYS1 (Initial setting) / SUBW SYS2
Select either SYS1 or SYS2 for the desired subwoofer effect.
SUBW SYS1: Subwoofer level changes according to the main volume setting.
SUBW SYS2: Subwoofer level change is different from the main volume setting.
For example, even at low volume settings, the subwoofer is still audible.
Visual Customizing
Changing Lighting Colour
ILLUMI BLUE (Initial setting) / RED
You can change the lighting colour of the buttons.
BLUE RED
Dimmer Control
DIMMER AUTO (Initial setting) / DIMMER MANU
Set the DIMMER control to AUTO to decrease the illumination brightness of the
unit with the head lights of the vehicle ON. This mode is useful if you feel
the unit’s backlighting is too bright at night.
· If your vehicle should have a dimmer control for the dashboardlights, never
connect the DIMMER cable (orange) of the radio to this dimmer control.
Scroll Type Setting
SCROLL TYPE1 / SCROLL TYPE2 (Initial setting)
Choose from two scrolling methods. Select the type you prefer.
Scroll Setting (TEXT SCROLL)
SCROLL AUTO / SCROLL MANU (Initial setting)
This CD player can scroll the disc and track names recorded on CDTEXT discs,
as well as the text information of MP3/WMA files, folder names, and tags.
SCROLL AUTO: The CD text information, the text information of folder and file
names, and the tags are scrolled automatically. Also, tag information is
automatically scrolled without pressing TITLE in the tag information display
mode.
SCROLL MANU: The display is scrolled when a disc is loaded or when a track is
changed, etc.
18-EN
· The unit scrolls CD text names, folder names, file names or tag display.
Demonstration
DEMO ON / DEMO OFF (Initial setting) This unit has a demonstration feature for
the display.
· To quit Demo mode, set to DEMO OFF.
MP3/WMA
Playing MP3/WMA Data (PLAY MODE)
CDDA (Initial setting) / CDDA/MP3
This product can playback CDs containing both CD and MP3/WMA data. However, in some situations (some enhanced CDs), playback may be difficult. For these special cases, you can select playback of CD data only. When a disc contains both CD or the MP3/WMA data, playback starts from the CD data portion of the disc.
CDDA :
Only CD data can be played back.
CDDA/MP3 : Both CD data and MP3/WMA file tracks can be played back.
· Perform this setting before inserting a disc. If a disc has already been inserted, perform the setting after you remove the disc.
External Device
Connecting to an External Amplifier
POWER IC ON (Initial setting) / POWER IC OFF
When an external amplifier is connected, sound quality can be improved by
stopping the power supply of the built-in amplifier.
POWER IC OFF : Use this mode when the front pre-amplifier of the unit is used
to drive an external amplifier connected to the speakers. In this setting, the
head unit’s internal amplifier has no output to drive speakers.
POWER IC ON : The speakers are driven by the built-in amplifier.
SPEAKER RIGHT FRONT
Speakers
Front right
SPEAKER RIGHT REAR
SPEAKER LEFT REAR
Rear right
Rear left
SPEAKER LEFT FRONT
Front left
· No sound is produced by the system when the power output is set to OFF.
Amplifier
Front left
Front right
19-EN
iPodTM (Optional)
Rotary
encoder SOURCE/POWER
/
MODE
FUNC.
45
6 TITLE
An iPodTM, iPodTM mini or iPodTM nano can be connected to the CDE-9850Ri by
using the FULL SPEEDTM Connection Cable (supplied). When the CDE-9850Ri is
connected by using the cable, the controls on the iPodTM are not functional.
About iPodsTM usable with this unit The unit can be used with third generation
and above iPodTM photo, iPodTM minis or iPodTM nano. iPodTM Shuffle cannot be
used, however.
· Touch wheel or scroll wheel type iPods without the dock connector cannot be
connected to the unit.
· The unit can be used with the following iPod versions. Correct function of
earlier versions canno
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>