iReSt G600-8 Massage Chair Instruction Manual
- June 3, 2024
- iReSt
Table of Contents
iReSt G600-8 Massage Chair
Thanks for purchasing this product. Please read this manual instruction
carefully in order to know how to use this product correctly before operation.
Please pay more attention to some important safety warnings and keep this
manual book properly for future use.
Note: Our Company reserves the right to revise the design and description
of this product without any further notice. Please refer to the actual color
of this product.
IMPORTANT SAFETY INSTRUCTIONS
Warning:
This product can expose you to chemicals including lead which is known to the
State of California to cause cancer or birth defects or other reproductive
harms. For more information go to www.P65Warnings.ca.gov/furniture. When using
an electrical appliance, basic precautions should always be followed,
including the following: Read all instructions before using (this appliance)
DANGER- To reduces the risk of electric shock:
Always unplug this appliance from the electrical outlet immediately after
using it and before cleaning.
WARNING- To reduces the risk of burns, fire, electric shock, or injury to
Persons:
- An appliance should never be left unattended when plugged in. Unplug from the outlet when not in use, and before putting on or taking off parts.
- Do not operate under a blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.
- Close supervision is necessary when this appliance is used by, on.or near children, invalids, or disabled persons.
- Use the appliance only for its intended use as described in this manual.
- Never operate this appliance if it has a damaged cord or plug if it is not working properly if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.
- Do not carry this appliance by supply cord or use the cord as a handle.
- Keep the cord away from heated surfaces.
- Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the like.
- Never drop or insert any object into any opening.
- Do not use outdoors.
- Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
- To disconnect, turn all controls to the off position, then remove the plug from the outlet.
- The appliance is intended for household and indoor use only.
- Connect this appliance to a properly grounded outlet only, See grounding instructions.
- Keep children away from extended foot support (or other similar parts )
- Do not use a massager in close proximity to loose clothing or jewelry.
- Keep long hair away from massager while in use.
- Connect this appliance to a properly grounded outlet only. See Grounding Instructions.
- Do not use a massager in close proximity to loose clothing or jewelry.
- Keep long hair away from massager while in use.
SAVE THESE INSTRUCTIONS GROUNDING INSTRUCTIONS
This product must be grounded,if it should malfunction or breakdown, grounding
provides a path of least resistance for electric current to reduce the risk of
electric shock, this product is equipped with a cord having an equipment
grounding conductor and a grounding plug, the plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with
all local codes and ordinances
DANGER
improper connection of the equipment grounding the conductor can result in a
risk of electric shock, check with a qualified electrician or serviceman if
you are in doubt as to whether the product is properly grounded, and do not
modify the plug provided with the product if it will not fit the outlet, have
a proper outlet installed by a qualified electrician
- This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in a sketch on page 16 , A temporary adapter that looks like the adapter illustrated in sketches B and C may be used to connect this plug to a 2-pole receptacle as shown in the sketch
- if a properly grounded outlet is not available the temporary adapter should be used only until a properly grounded outlet (sketch A )can be installed by a qualified electrician, the green-colored rigid ear, lug , or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover, Whenever the adapter is used,it must be held in place by a metal screw
Massage System Lnstallation
- select a concrete or wood or chinaware platform with an area of more than40cm*36cm
- drill four holes on each corner with a diameter of 7.8mm
- locked the massage chair on the platforms
- Connect black pipe to black pipe, and connect white pipe to white pipe.
Name and function of components
- Detachable pillow pad
- USB Charging Port
- Controller
- Armrest
- Detachable
- The back covering
- trackpad
- Tray
- wireless recharge station
Function
- Designed with a four-wheel driven muted massage mechanism that can move up and down in the backrest.
- Air pressure function: Buttock is equipped with 5 airbags, with 2 modes and 2 strengths.
- Programmed with five kinds of emulation massage functions of Shiatsu, kneading, flapping, knocking, and synchronous kneading and flapping.
- Programmed with manual and automatic control modes for the upper body.
- Under the automatic mode, it offers three automatically changed combinations of massage functions: lower, upper and full. Under the manual mode, it offers three options of overall, fixed, and partial area. Under the fixed state, the massage hands can be moved up and down; Each massage function has five levels of speed options; the width between the two massage hands can be adjustable in three levels of wide, middle, and narrow when it is under flapping, shiatsu or knocking state.
- Seat frame forward and backward movement, backrest reclining, and declining movement.
- Restoring the massage hands after turning off the machine
- Design with a USB charger on the right armrest.
- Design with wireless charging function.
Method of usage
Method of usage
Components install direction
- Place the bottom frame of the massage chair on the spa tub.
- Make sure the holes in the bottom frame are aligned with the pre-drilled holes on the spa tub.
- Secure the massage chair onto the spa tub by using provided hardware as shown in the diagram below.
Armrest assembling instructions
- Insert the bolt of the handrail connection plate into the positioning hole of the armrest support plate on the moving frame.
- Lock the corresponding bolt with one M12 I-type non-metallic insert locking nut and three M6 I-type non-metallic insert locking nut sets.
- Put the backrest support shaft into the card slot of the backrest support seat. (Note: The shaft can only be put into the card slot at a certain angle).
- Erect the backrest, the self-locking hook will lock the cylinder limit shaft automatically.
Warning: Before operating the massage, please ensure that the backrest electric cylinder and the pin which fixed the backrest connect correctly, and the backrest must be erected before turning on the massage chair. Otherwise, after being turned on, the front of the electronic cylinder will hit the board under the seat frame, resulting in the seat frame deformation, and even derailing or damaging the steel ball railway.
0peration sequence
SWITCH ON POWER
- and inserts the plug into the socket outlet.
- switch on the power button behind the armrest.
MASSAGE
Select relative massage according to the operating instructions of the
control.
SWITCH OFF POWER
- stop the overall message.
- switch off the power button behind the armrest.
- pull the plug out of the socket outlet.
Attaching or detaching the pillow pad and back cushion
The pillow pad and back cushion (recommended) reduce the kneading intensity of
your neck and shoulder, but you can decide to put it on or not according to
your personal need.
WARNING: IN CASE OF DANGER, DO NOT REMOVE THE CUSHION
To Adjust The Back Simultaneously
Backrest adjustment
Press and hold the ‘9 buttons on the controller. the backrest will recline
backward slowly. Release the button. then the backrest will be stopped the
upright
press and hold the C button on the controller. the backrest will move slowly.
Lose the button. then the backrest will be
To Adjust Seat Frame Separately
The flex function of the seat frame could fix the different heights of the
people to adjust the massage place of the calf airbags. the maximum distance
moving forward and backward is 120mm.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: This device may not cause harmful interference,
and this device must accept any interference received, including interference
that may cause the desired operation. This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses ru1d can radiate radio frequency energy ru1d, if not installed
and used in a.cc-or dance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause ha1n1ful interference to radio or television reception, which cru1
be determined by turning the equipment off and on, the ser is encouraged to
try to connect the inte1ference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for a tuicontrolled environment. This transmitter must not be co-located or operating in c-onjtu1ction with any other antenna or transmitter