DORMAN 599-211XD Climate Control Module Instruction Manual
- June 1, 2024
- DORMAN
Table of Contents
DORMAN 599-211XD Climate Control Module
Product Specifications
- Model: 599-211XD
- Function : Climate Control Module
- Configuration: Automatic after installation
- Support: Technical Support is available at 866-933-2911
Product Usage Instructions
Installation and Configuration
This Climate Control Module will automatically undergo a configuration
procedure after installation. Follow the steps below:
- Start the vehicle with the new module installed. The engine must be running throughout the process.
- Wait for the configuration sequence to complete. LEDs will indicate the progress according to the vehicle application.
- Configuration may take up to one minute.
- Configuration is complete when all button LEDs turn off.
- If the configuration fails, follow these steps:
- Unplug both connectors to remove power from the module.
- Wait for 15 seconds before reattaching both connectors.
- Repeat the procedure starting from Step 1.
- If the configuration fails after two attempts, contact Technical Support at 866-933-2911.
ATTENTION: Refer to the appropriate shop manual for your vehicle to obtain specific service procedures for this part. If you do not have a service manual or lack the skill to install this part, it is recommended that you seek the services of a qualified technician. Pay special attention to all cautions and warnings included in the shop manual. Read and follow all instructions carefully. This product is only designed to function properly on specific vehicle applications. Please verify that the vehicle requirements match the product specifications and application notes for this part.
- Cadillac Escalade 2006–2003; Chevrolet Avalanche, Suburban, Tahoe 2006–2003;
- GMC Sierra 2007–2003; GMC Yukon 2006–2003; Chevrolet Silverado 2007–2003;
- Hummer H2 2007–2003; Buick Rainier 2007–2004; Chevrolet Trailblazer 2009–2002;
- GMC Envoy 2009–2002; Oldsmobile Bravada 2004–2002
This Climate Control Module will automatically undergo a configuration procedure after installation. DO NOT use an external programmer or scan tool. Follow the procedure below to complete the configuration. If the unit fails to configure after two attempts, call Technical Support at 866-933-2911.
Configuration Instructions
- A. With the new module installed, start the vehicle to begin automatic configuration. The engine must be running for the entire process.
- B. Wait while the system performs a configuration sequence. While configuration is in process LED(s) will be lit according to the vehicle application. See Table A below.
- a. Configuration may take up to one minute
- C. Configuration is complete when all button LEDs turn off.
- D. If the configuration is unsuccessful:
- a. Remove power from the module by unplugging both connectors.
- b. Wait 15 seconds. Reattach both connectors.
- c. Repeat the procedure beginning with Step A.
- d. If the configuration is unsuccessful after two attempts, call Technical Support at 866-933-2911.
Table A
Configuration
Number
| Vehicle Applications| LED Active
During Configuration
01
| 2003–2004 (Cadillac) Escalade, (Chevrolet) Avalanche, Suburban, Tahoe, (GMC) Yukon
2003–2004 (Chevrolet) Silverado, (GMC) Sierra
| Rear Defrost (C)
02
| 2005–2006 (Cadillac) Escalade, (Chevrolet) Avalanche, Suburban, Tahoe, (GMC) Yukon
2005-2007 (Chevrolet) Silverado, (GMC) Sierra
| Front Defrost (B)
03| 2003–2007 (Hummer) H2| Front and Rear Defrost
(B & C)
04
| 2004 (Buick) Rainier
2003–2004 (Chevrolet) Trailblazer, (GMC) Envoy, (Oldsmobile) Bravada
| Recirculation (A)
05| 2005–2006 (Buick) Rainier
2005–2006 (Chevrolet) Trailblazer, (GMC) Envoy
| Recirculation and Rear Defrost
(A & C)
---|---|---
06| 2002 (Chevrolet) Trailblazer, (GMC) Envoy
2002 (Oldsmobile) Bravada
| Recirculation and Front
Defrost (A & B)
07| 2007 (Buick) Rainier
2007–2009 (Chevrolet) Trailblazer, (GMC) Envoy)
| Recirculation, Front and Rear
Defrost (A, B, & C)
Disclaimer:
Even though every attempt is made to ensure this information is complete and
accurate, it is impossible to account for all possible circumstances or
situations. Please consult with a qualified auto technician before attempting
to perform any work you are not qualified to do. Automobiles can be hazardous
to work on; be sure to take all necessary safety precautions. Failure to do so
may result in property damage or personal injury. Certain motor vehicle
standards and performance requirements may apply to your motor vehicle (such
as Federal Motor Vehicle Safety Standards by the National Highway Traffic
Safety Administration). Be sure that your work is performed in accordance with
such standards and that you do not disable any motor vehicle safety feature.
Dorman Products, Inc. | Corporate Office and Customer Service:
1-800-523-2492
©2020 No reproduction in whole or in part without prior written approval.
FAQ
- Q: What should I do if the configuration process fails?
- A: If the configuration is unsuccessful, unplug both connectors to remove power from the module, wait for 15 seconds, reattach both connectors, and repeat the configuration procedure. If unsuccessful after two attempts, contact Technical Support at 866-933-2911.
- Q: How long does the configuration process take?
- A: The configuration process may take up to one minute to complete.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>