delta HDRS6200 Heavy Duty Upright Stand for Two Bikes Instruction Manual
- June 1, 2024
- Delta
Table of Contents
delta HDRS6200 Heavy Duty Upright Stand for Two Bikes Instruction Manual
Assembly instructions
Parts
- A x1 — H Piece
- B x2 — Straight poles
- C x1 — U piece
- D x2 — Legs
- E x4 — Arms
- F x6 — Bolts
Tool Required
- Phillips Head Screwdriver
WARNING
DO NOT EXCEED MAXIMUM TOTAL WEIGHT LIMIT OF 100 LBS (45.4 Kgs) – HDRS6002 / 80
LBS (36 Kgs) – RS6002 MAX LOAD PER HOOK: 25 LBS (11.4 kgs) / MAX WEIGHT
PER BIKE: 50LBS (22.7 kgs)
-
Do not tighten bolts until rack is fully assembled and tubes are properly aligned.
-
-
Tighten all bolts before using
Spread legs apart to max width before tightening -
Adjust height of arms before they bear any weight.
IMPORTANT / SAFETY
In order to avoid accidental toppling of the rack, a wall stabilising strap is
supplied. This should be attached to the rack at one end with the bolt
provided. The other end of the strap should be secured to the wall using a
screw that is suitable for the type of wall construction. If in doubt, consult
your hardware merchant for the correct method of xing based on the wall
construction.
Delta Cycle Corporation
36 York Avenue, Randolph, MA 02368 USA
800-474-6615 /
www.designbydelta.com
Service: Please do not return to store; for immediate response email
service@designbydelta.com
Parts
- A x1- Top Connector
- B x2-Top Pole
- C x2-Center Pole
- D x2-Bottom Pole
- E x2- Base Stand (Left + Right)
- F x1 – Base Bracket
- G x4-Long Bolts
- H x8-Arms
- I x6-Short Bolts
- J x2-Extra Long Bolts
- K x2-Nuts (10mm)
- L x2-Washers
- M 4×4-0 Ring
- N x1-Mesh Basket
Tool(s) Required
-
Phillips Head Screwdriver
-
Adjustable Wrench (or 10mm)
WARNING
DO NOT EXCEED MAXIMUM TOTAL WEIGHT LIMIT OF 160 LBS (70 Kgs) MAX LOAD PER
HOOK: 35 LBS (15.9 kgs) / MAX WEIGHT PER BIKE: 40LBS (18.2 kgs) LOAD HEAVIER
BIKES, INCLUDING E-BIKES, ON LOWER TIER.
-
Connect base bracket (F), bottom poles (D) and base stand (E) as shown using long bolts (G, J) Nuts (K) and Washers (L). Do not tighten bolts until rack is fully assembled and tubes are property aligned. Fully assemble base before continuing.
-
Connect center poles (C) to bottom poles (D). secure with short bolts (1).
-
Use short bolt (1) to attach basket (N) by positioning in line with desired height hole on the inside of the center pole (C ) (FIGURE 1)
Connect top poles (B) to center poles (C), secure with short bolts (1). Connect top connector (A) to top poles (B) using long bolts (G). -
Tighten all bolts, using the wrench to hold nuts where needed.
O Rings (M) can be used to slide over base legs where needed on uneven floor surfaces.
-
After rack is assembled Arms should be placed at desired height – two per bike (front and rear).
Adjust position of arms before placing bike on stand.
IMPORTANT / SAFETY
Always load bikes on the arms of the bottom, front side of the rack first to
maintain stability.
Remove bikes from the top first.
Store e-bikes and other heavy bikes on lower arms only.
Do not allow children to play or hang from rack
Delta Cycle Corporation
36 York Avenue, Randolph, MA 02368 USA
800-474-6615/www.designbydelta.com
Copyright 2023
Service: Please do not return to store; for immediate response email
service@designbydelta.com
Parts
- A x1 — Top Connector
- B x2 — Top Pole
- C x2 — Center Pole
- D x2 — Bottom Pole
- E x2 — Base Stand (Left + Right)
- F x1 — Base Bracket
- G x4 — Long Bolts
- H x8 — Arms
- I x4 — Short Bolts
- J x2 — Extra Long Bolts
- K x2 — Nuts (10mm)
- L x2 — Washers
- M x4 — O Ring
Tool(s) Required
-
Phillips Head Screwdriver
-
Adjustable Wrench (or 10mm)
WARNING
DO NOT EXCEED MAXIMUM TOTAL WEIGHT LIMIT OF 160 LBS (70 Kgs) MAX LOAD PER
HOOK: 35 LBS (15.9 kgs) / MAX WEIGHT PER BIKE: 40LBS (18.2 kgs) LOAD HEAVIER
BIKES, INCLUDING EBIKES, ON LOWER TIER.
-
Connect base bracket (F), bottom poles (D) and base stand (E) as shown using long bolts (G, J) Nuts (K) and Washers (L). Do not tighten bolts until rack is fully assembled and tubes are properly aligned. Fully assemble base before continuing.
Front side of rack features the longer section of the base foot -
Connect centre poles (C) to bottom poles (D), secure with short bolts (I).
-
Connect top poles (B) to centre poles (C), secure with short bolts (I). Connect top connector (A) to top poles (B) using long bolts (G).
-
Tighten all bolts, using the wrench to hold nuts where needed.
O Rings (M) are included toto slide over the base legs to ensure balance on uneven floors (Figure 1)
-
After rack is assembled Arms should be placed at desired height – two per bike (front and rear).
Adjust position of arms before placing bike on stand.
IMPORTANT / SAFETY
Always load bikes on the arms of the bottom, front side of the rack farts to maintain stability. Remove bikes from the top farts.
E bike storage on lower tier only.
Do not allow children to play or hang from rack.
Need help? Please do not return to store.
For immediate response email
service@designbydelta.com
Delta Cycle Corporation
36 York Avenue, Randolph, MA 02368 USA
800-474-6615 /
www.designbydelta.com © Copyright 2020
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>