AUXBEAM QP009631 9 Inch LED Round Lights Instruction Manual

: June 1, 2024
: AUXBEAM

Table of Contents

AUXBEAM QP009631 9 Inch LED Round Lights
Product Information
Product Usage Instructions
FAQ
Introductions & Tips
Package List
Lighting Effects
Installation Steps
Wiring Diagram
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AUXBEAM QP009631 9 Inch LED Round Lights

AUXBEAM-QP009631-9-Inch-LED-Round-Lights-product

Product Information

Specifications

Product Name: 9INCH LED HEADLIGHTS & 4INCH FOG LIGHTS
Model Numbers: QP009631, QP009524, QP006349
Package Contents:
- QP009631: 2x 9inch Headlights, 2x 4inch Fog Lights, 4x 15mm Springs, 6x Hex Socket Screws, 2x 9005 Female To H13 Male Adapter, 2x 9005 Female Adapter, 4x External Wires, 2x Brackets For Modified Steel Bumper, 2x Brackets For Plastic Bumper, 8x T-Tap Connector
- QP009524: 2x 9inch Headlights, 4x 15mm Springs, 6x Hex Socket Screws, 2x External Wires, 4x T-Tap Connector
- QP006349: 2x 4inch Fog lights, 2x 9005 Female To H13 Male Adapter, 2x 9005 Female Adapter, 4x T-Tap Connector
Lighting Effects: White DRL Halos, Amber Turn Signals, Low Beams + Fog Lights (QP009631), High Beams + Fog Lights (QP006349)

Product Usage Instructions

Installation Steps

Tools required: Flat Head Screw Driver or Nylon\ Panel Removal Tool, 10mm Socket, Ratchet/Drill, Ratchet external 10mm and 13mm Wrenches.

Open the hood of your car. Remove the grill by taking out the 6 push pins using a flat head screwdriver or panel popper.
Next remove the stock headlights held in with 3 bolts on each light, using a socket. Unplug the stock headlights by pushing the backside connector tab on the wiring harness with your thumb.
Now you need to locate the stock fender connector on each side. Remove the ground wires from the fender next to the battery on passengers side. Remove the nut next to it holding them to the fender (be very careful not to drop the nuts). Move the ground wires out of the way to access the front fender harness. It is located directly below the ground bolts.
Test all functions of the new LED headlights, reinstall the black box with the 10mm bolts back on the fender.
Make sure the beam locations are not too high up and\ potentially blinding oncoming traffic, reinstall the grille and secure it with the original push rivets.
Fog lights installation: First, remove the bumper. And then disconnect the stock fog light power connector, remove your stock JL fog lights. Reinstall your new LED fog lights. Determine which brackets you will need below. Run the DRL and Amber Turn signal wires into the fender area. Please note our JL fog lights can NOT be installed on the 10th Anniversary bumper, please make sure before purchasing, thanks!

FAQ

Q: What should I do if I encounter problems during installation?
- A: If you encounter problems during the installation process, please feel free to contact our customer support team for assistance.
Q: Can the JL fog lights be installed on a 10th Anniversary bumper?
- A: No, our JL fog lights cannot be installed on the 10th-anniversary bumper. Please ensure compatibility before purchasing.

Introductions & Tips

Thank you for purchasing our headlight products. This guide will provide you with detailed steps and tips to make the installation process easy andenjoyable. Before starting the installation, it is important to ensure your personal safety and complete the installation efficiently.

This manual is applicable to the following three products: QP009631 HEADLIGHT/FOG KIT, QP009524 HEADLCHTS, QP006349 FOG LGHTS.
Read the instructions: Before starting the installation, please be sure to read the entire installation manual carefully. Familiarize yourself with the steps and requirements to avoid misuse.
Avoid risks involved: If you do not have the necessary skills or experience, or are not familiar with automotive electrical systems, it is recommended that you ask professional technicians to assist in the installation to avoid potential risks.
Consult in time if you have any questions: If you encounter problems during the installation process, please feel free to contact our customer support team. Don’t hesitate, we are here to help you.

Package List

QP009631 INCLUDES: $AUXBEAM-QP009631-9-Inch-LED-Round-Lights-fig $1$$

2x 9inch Headlights
2x 4inch Fog Lights
4x 15mm Springs
6x Hex Socket Screws
2X 9005 Female To H13 Male Adapter
2x 9005 Female Adapter
4x External Wires
2x Brackets For Modified Steel Bumper
2x Brackets For Plastic Bumper
8x T-Tap Connector

QP009524 INCLUDES:

2x 9inch Headlights
4x 15mm Springs
6x Hex Socket Screws
2x External Wires
4x 15mm Springs
4x T-Tap Connector

QP006349 INCLUDES:

2x 4inch Fog lights
2x 9005 Female To H13 Male Adapter
2x 9005 Female Adapter
4x T-Tap Connector

Lighting Effects

$AUXBEAM-QP009631-9-Inch-LED-Round-Lights-fig $4$$

Installation Steps

NOTE: If you purchased QP009631 HEADLIGHT/FOG KIT, please refer to steps 1-11. QP009524 HEADLCHTS please refer to steps 1-7 and QP006349

FOG LGHTS please start directly from step 9.

Tools required : Flat Head Screw Driver or Nylon Panel Removal Tool 10mm Socket, Ratchet/Drill and Ratchet external 10mm and 13mm Wrenches.

Open the hood of your car. Remove the grill by taking out the 6 push pins using a flat head screwdriver or panel popper.
Next remove the stock headlights held in with 3 bolts on each light, using a socket. Unplug the stock headlights by pushing the backside connector tab on the wiring harness with your thumb.
Plug in both the provided headlight wire plugs and the factory headlight sockets and reinstall your new LED JL headlights into your vehicle. Re-use the 3 mounting screw sand connect the new headlight connector into the stock JL headlight connector. If not wiring up DRL or amber turn signals you can proceed to
step 7. If you plan to use the DRL or amber turn signals lights, run the DRL and amber turn signal wires into the fender area and back towards the firewall by using the provided external wires (refer to wiring diagram).
Now you need to locate the stock fender connector on each side. Remove the ground wires from the fender next to the battery on passengers side. Remove the nut next to it holding them to the fender (be very careful not to drop the nuts). Move the ground wires out of the way to access the front fender harness. It is located directly below the ground bolts.
Pull the fender liner back to gain access to the DRL/side marker bracket. Remove the bolts and loosen the two bolts holding the bracket in place. Locate the stock JL Fender Wire Harness connector.
Pull back wheel liner, we can see factory fender lights wires. Refer to wiring diagram, on the left drivers side, the WHITE-GREEN wire is for turn signal light, the WHITE-YELLOW one is for daytime running light. On the right passengers side, the WHITE-BEIGE wire is for turn signal light, the WHITE DARK BLUE one is for daytime running light. Using T-tap connectors and external wires, connect the yellow external wires of the new LED headlights to the factory turn signal wires and connect the white external wires to the factory daytime running light wire.
Test all functions of the new LED headlights, reinstall the black box with the 10mm bolts back on the fender.
Make sure the beam locations not too high up and potentially blinding oncoming traffic, reinstall the grille and secure it with the original push rivets.
Fog lights installation: First, remove the bumper. And then disconnect the stock fog light power connector, remove your stock JL fog lights. Reinstall your new LED fog lights. Determine which brackets you will need below. Run the DRL and Amber Turn signal wires into the fender area. Please note our JL fog lights can

NOT be installed on the 10th Anniversary bumper, please make sure before purchasing, thanks!

3 Base Fitment list

2018-2022 Jeep Wrangler JL JLU Wrangler 4xe
Sport and Sport S model, Wrangler JL Sport
Sahara and the Rubicon with factory Plastic bumper

4 Base Fitment list

Sahara or Rubicon Wrangler JL with OEM plastic bumper
Aftermarket bumpers using the OEM “4 Bolt” mounting style location
10 Refer to wiring diagram, connect DRL wire (white external wire) and turn signal wire (yellow external wire) on your new LED fog lights to the JL factory fender wire harness by using T-tap connectors. On the left drivers side, the WHITE-GREEN wire is for the turn signal light, the WHITE-YELLOW one is for DRL; On the right passengers side, the WHITE-BEIGE wire is for the turn signal light, the WHITE-DARK BLUE one is for DRL.
11.Turn on the new fog lights while holding the lamp in place. Rotate the adjustment screw (clockwise to raise, counterclockwise to lower) on the rear of the lamp to aim the light like the existing fog light. When the existing and new fog light horizon lines are aligned, re-torque all bolts of fog lights.

NOTE: You can also connect DRL external wires to the fuse F52 (cigarette lighter) and ground the negative wire to negative battery post (fuse and negative wire are NOT included).

Wiring Diagram

Your factory fender lights wires may be a different configuration than the one used in this instruction guide. Below are the wiring configurations of 5 wires for stock headlights are led and 6 wires for stock headlights are halogen. Thus, your installation or wiring may differ. You can use a multi-meter or consult your model’s wiring diagram to ensure proper function

6 Wires for Stock Headlights are halogen Wiring Diagram(Note: wire colors may vary) $AUXBEAM-QP009631-9-Inch-LED-Round-Lights-fig $6$$

6 Wires for Stock Headlights are Halogen Left Driver Side

Pin	Factory Wire Color	Circuit	Wire Connection
①	BK	Ground	–
②	WH/YE	Left Drl Lamp Driver	White External Wire
③	WH/BN	Left Front Park Lamp Driver	–
④	BK	Ground	–
⑤	WH/GN	Left Front Turn Lamp Driver	Yellow External Wire
⑥	WH/OG	Left Side Marker Control Base	–

6 Wires for Stock Headlights are Halogen Right Passenger Side

Pin	Factory Wire Color	Circuit	Wire Connection
①	BK	Ground	–
②	WH/DB	Right Drl Lamp Driver	White External Wire
③	WH/OG	Right Front Park Lamp Driver	–
④	BK	Ground	–
⑤	WH/BG	Right Front Turn Lamp Driver	Yellow External Wire
⑥	BG/OG	Right Side Marker Control Base	–