AUXBEAM QP005925 LED Fog Lights Instruction Manual

AUXBEAM QP005925 LED Fog Lights

BRAND INTRODUCTION

Founded in 2008, Auxbeam strives every day to share our enjoyment of open-air, off-road adventure with as many people as possible. Today, Auxbeam has achieved a leading market position on account of affordable prices and updated excellent quality products, high standards of manufacturing and superior customer service. Nowadays… Auxbeam focuses on providing all types of cost- effective outdoor auto spare parts in special design styles to meet different customers’ needs. We offer a wide variety of items, including auto parts & accessories, LED lights, switch panels and so on.

TIPS

1. Safety First: Prioritize safety by disconnecting the vehicle battery’s negative terminal before starting the installation.
2. Follow the Manual: Always follow the manufacturer’s instructions for the specific  LED fog lamp assembly you are installing.
3. Quality Check: Test the fog lamps thoroughly before driving at night to ensure proper functionality.
4. Carefully install: Avoid over-tightening screws or bolts during installation to prevent damage to the new assembly or the vehicle.
5. Timely consultation: If you are unsure about any aspect of the installation, please remember to consult us anytime.

LED FOG LIGHT WIRING DIAGRAM

If your truck does not have stock fog lamps, you may need to buy an extra wiring harness and refer to the wiring diagram below.

NOTE

1. These fog lights are designed to replace the original fog lights, wire harness is not included.
2. The wiring diagram of the wiring harness may be different.
3. If your truck has stock fog lamps, please follow the installation steps.

INSTALLATION STEPS

Step 1: Disconnect the Battery

• Turn off the vehicle.
• Disconnect the negative terminal of the vehicle battery to ensure safety during the installation.

Step 2
Step 2: Remove the Old Fog Lamp Assembly

• Use appropriate tools (screwdriver or socket set) to remove
  screws or bolts securing the old fog lamp assembly.

• Disconnect the wiring harness from the old assembly.

Step 3: Prepare the New LED Fog Lamp Assembly

• Refer to the vehicle manufacturer’s instructions for specific installation guidelines.
• Transfer any necessary components from the old assembly to the new one if required.

Step 4: Mount the New Fog Lamp Assembly

• Position the new LED fog lamp assembly in the original location.
• Secure the assembly in place by tightening screws or bolts.

Step 5: Wire the LED Fog Lamps

• If your original fog lamp plug is a 5202 standard plug, just plug and play, then skip to step 8.
• If your original fog lamp plug is not a 5202 standard plug, please follow steps 6-7.
• Please refer to the wiring diagrams if your truck does not Standard Plug have stock fog lamps.

Step 6: Connect Power and Ground
Identify the power (positive, RED) and ground (negative, BLACK) wires from the new LED fog lamp assembly.

• Strip a small section of insulation from the end of each wire.
• Connect the power wire from the new LED fog lamp assembly to the corresponding power wire in the vehicle’s wiring.
• Connect the ground wire from the new assembly to the vehicle’s ground wire.

Step 7: Insulate and Secure Wiring

• Cover each connection with heat shrink tubing or electrical tape.
• Secure the wiring with zip ties to prevent dangling or contact with hot engine components.

Step 8: Reconnect the Battery

• Reconnect the negative terminal of the vehicle battery.

Step 9: Test the LED Fog Lamps

• Turn on the vehicle and test the functionality of the new LED fog lamps.
• Ensure they turn on and off as expected.

Step 10: Adjust the Fog Lamps

• Aim the new LED fog lamps properly for the desired illumination.

Step 11: Check Local Regulations

• Verify compliance with local laws regarding aftermarket LED fog lamps.

FOG LIGHT AIMING

There are two important issues to address when installing fog lights. The first is to minimize the amount of return glare into the drivers’ eyes, and the other is to minimize glare into oncoming eyes. Both of those issues must be accomplished while putting as much light as possible on the road. Firstly, Park your vehicle on a level surface, 25 feet away from a wall. And then measure the distance between the centre of the fog light and the ground. You should also mark the corresponding height on the wall. Finally, adjust the lighting angle by rotating the adjustment screw so the top of the fog beam pattern is about 4 inches down from the lamp centre at 25 feet, with the lamp facing straight forward. (See below.)

CAUTIONS
READ ALL SAFETY MESSAGES AND UNDERSTAND ALL INSTRUCTIONS BEFORE ATTEMPTING TO INSTALL THIS PRODUCT. ALWAYS WEAR SAFETY GLASSES DURING INSTALL.

QUESTIONS & ANSWERS

Q: WHEN TO USE FOG LIGHTS?
A: Fog lights are designed to be used when visibility is severely restricted, typically due to fog, but also in other poor visibility conditions such as snow or heavy rain. The Highway Code (Rule 226) states: “You MUST use headlights when visibility is seriously reduced, generally when you cannot see for more than 100 metres (328 feet). You may also use front or rear fog lights but you MUST switch them off when visibility improves.”

Q: MY TRUCK DIDN’T COME WITH STOCK FOG LAMPS BEFORE, CAN I WIRE FOG LIGHTS DIRECTLY TO A BATTERY?
A: Yes, you can. At the very least you need to include a fuse and a switch (NOT include- ed) in a series with them. And it may be a lot neater and easier to use a spare position in an existing fusebox. In many cases, a vehicle wired this naively would fail annual inspection. There seem to be rules about combining lights that don’t always make sense. So you might need a relay or some other way of linking to the ignition and/or headlight circuit
NOTE: The wiring diagram of the wiring harness may be different if you encounter any problems, please consult the relevant manufacturer.

Q: HOW TO REMOVE THE MOISTURE IN THE HEADLIGHTS?

A: First, remove the headlights and open the vent Vent Valve valve on the back cover, with the front panel facing down and the cover facing up. Second, turn on the light for half an hour to remove the moisture. Third, after removing the moisture, cover the vent valve and install it back in your car.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>