AMP AHS-630X InfusePro Thin Step Light Installation Guide
- September 19, 2024
- AMP
Table of Contents
AMP AHS-630X InfusePro Thin Step Light
Specifications
- Product Model : AHS-630X
- Maximum Power Supply Rating : 300 watts (25 AMPS) at 15 volts
- Main Low Voltage Cable Burial Depth : Less than 6 inches (152 mm)
Product Usage Instructions
Install Luminaire
NOTE: Must be mounted with the wire exit on the left.
- Anchor: Anchors are required for concrete or brick walls. Hold the luminaire on the wall and mark two points for the anchors using the mounting holes as guides. Then drill the proper holes using the marks. Insert the anchors into the drilled holes.
- Screw Luminaire: Attach the luminaire onto the desired mounting surface and secure with the screws. Hand tighten until snug with a screwdriver. Lastly, caulk around fixture to ensure it is sealed from water.
Wire Connections
Supply Cables
Wire Connectors Main Supply Cables
Pigtail: Strip both leads from the luminaire pigtail. Using two wire
connectors (sold separately), connect the leads from the luminaire to the main
supply cable leads.
FAQ
-
Q: Can I install this luminaire near a pool, spa, or fountain?
A: No, all luminaires should be installed at least 10 feet (3.05M) away from pool, spa, or fountain to avoid any risk of electrical shock. -
Q: What should I do if I need to replace the lamp?
A: Turn off/unplug the luminaire and allow it to cool before replacing the lamp. Remember that the lighted lamp can be hot, so handle it carefully. -
Q: How deep should I bury the main low-voltage cable?
A: The main low-voltage cable is intended for shallow burial, less than 6 inches (152 mm).
INSTALLATION & MAINTENANCE GUIDE
AMP® LOW VOLTAGE LANDSCAPE LIGHTING
AMP® InfusePro Thin Step Light
ITEM: AHS-630X
1- 813-978-3900 • Mon-Fri 9am-6pm (EST)
IMPORTANT SAFETY INSTRUCTIONS : READ BEFORE INSTALLATION
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
- Make sure the power is turned OFF before installing or servicing this luminaire.
- WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pool, spa or fountain.
- This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
- Wiring connections must be made with UL-listed wire connectors that are suitable for outdoor use.
- Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
- The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm).
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSON’S LIGHTED LAMP IS HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
- Turn off/unplug and allow to cool before replacing lamp.
- Lamp gets HOT quickly! Contact only switch/plug when turning on.
- Do not touch the hot lens, guard or enclosure.
- Keep lamp away from materials that may burn.
- Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
- Do not operate the luminaire fitting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
PACKAGE CONTENTS
- A. (1) Luminaire
- B. (2) Anchors
- C. (2) Screws
PRODUCT DIMENSIONS
INSTALL LUMINAIRE
NOTE:
Must be mounted with the wire exit on the left.
Note: Anchors are required for concrete or brick walls. Hold the
luminaire on the wall and mark two points for the anchors using the mounting
holes as guides. Then drill the proper holes using the marks. Insert the
anchors into the drilled holes.
Attach the luminaire onto the desired mounting surface and secure with the
screws. Hand tighten until snug with a screwdriver. Last, caulk around fixture
to ensure it is sealed from water.
WIRE CONNECTIONS
Strip both leads from the luminaire pigtail. Using two wire connectors (sold separately), connect the leads from the luminaire to the main supply cable leads.
1-813-978-3900
Mon-Fri 9am-6pm (EST)
Specifications and product details subject to change without notice.
© Copyright 2023, AMP® Lighting, Lutz FL USA 33549
All rights reserved.
customersupport@amplighting.com
amplighting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>