AUXBEAM Q20 LED Headlight Bulbs User Manual
- June 13, 2024
- AUXBEAM
Table of Contents
AUXBEAM Q20 LED Headlight Bulbs
OVERVIEW
PRODUCT SPECIFICATIONS
- OPERATING VOLTAGE DC 12-16V
- WATERPROOF RATING IP68
- LED CHIPS Customized Auto Grade LED Chips
- HEAT DISSIPATION MODE Fan Cooling
- OPERATING TEMPERATURE -45°C — +150°C
- LIFESPAN 50,000 HOURS
- WARRANTY 2 YEARS
PRECAUTIONS BEFORE TESTING
- Please wear work gloves during installation.
- Do not touch the LED lamp beads directly or prevent any dirt or moisture from adhering to the LED.
- Do not look directly at the operating bulb since the light with high intensity will cause eye injury at a short distance. emperauce tay febut on severe odes or alow any skin contact since the bulbs each to very high
- Desot lisasemble or modify the product in any way, as this may damage the product or cause fire.
- Dause damage vehicle when the bulbs are on. Changes in the temperature of the LED bulbs may
PRE-INSTALLATION TESTING
- Remove the original bulb from the vehicle connector.
- Connect the LED bulb to the vehicle connector.
- Turn on the LED bulb and test for correct lighting.
- Check if any warning signs show up on the vehicle dashboard. If no warning occurs, the test is finished.
NOTE:
If one of the LED bulbs does not work, it could be attributed to poor contact.
Make sure the connection is good. If the problem cannot be solved, swap the
left side bulb with the right side bulb and test again.
(Remind: The socket has a polarity, please connect it correctly)
WARNING:
- Do not switch on the LED bulb until the connection is finished.
- If the LED bulb flashes or warnings show up on the dashboard, please connect the extra CANBUS to ensure correct operation.
If any problems still cannot be resolved under the guidance of this manual, please feel free to contact our customer support team.
INSTALLATION
H4/H1/H3/H13/9004/9007
- Remove the original bulb and collar
- Insert the bulb lamp as the direction of the arrow
- Use the circlip to lock the bulb
- Put the connector into the car socket
REMIND:
Please keep the led chip symmetric and hood upward as the photoshow.
If light pattern is not good,please rotate the body by tool.
H8/H9/H10/H11/H16/HB3(9005)/HB4(9006)
9012/5202/880/881/PSX24W/PSX26W/P13W
- Remove the original bulb and collar
- Insert the bulb lamp as the direction of the arrow
- Lock the bulb lamp by rotating 45degrees clockwise
- Put the connector into the car socket
H7
- Remove the original bulb and collar
- Insert the bulb lamp as the direction of the arrow
- Use the circlip to lock the bulb
- Put the connector into the car socket
TROUBLESHOOTING
Q: Lights not working
A: Check the plug and wiring first may wrong connection.
(9005 9006 9012 H7 with polarity, reverse male connector 180 degrees, and try
again.)
Q: Lights flicking/flash
A: Check the plug and wiring first may wrong connection; If failed,need
extra resistors(CANbus)to resolve the issue.
Q: Lights automatically on and off repeatedly
A: Overheat protection, check the cooling system if the fan works well.
Make sure enough space for heat dissipation in housing.
Q: One of the bulbs not working
A: Make sure correct connection;
If still failed, swap the left and right side bulbs try again;
Still invalid, may be caused by the vehicle’s light assembly.
Q: Vehicle dashboard appears with error/warning
A: This is a harmless side-effect of the unoriginal wattage LED bulbs not
being recognized by the vehicle’s system and can be resolved with the
installation of an additional set of resistors(CANbus).
Q: H7 Installation failed
A: Some vehicles(KIA, MAZDA, BMW, VW, MERCEDES, SAAB, HYUNDAI, etc)need
something very unique and not standardized H7 holders.
Please contact customer service for purchasing or local shop.
Note: The resistor(CANbus) is polarity sensitive.
If the LED bulbs do not function properly after installation, please reverse
the resistor(Canbus) male connector 180 degrees and try again.
BUYER READING
This product can only be used on road-legal automotive vehicles. AUXBEAM
cannot accept any responsibility and/or liability. It is your responsibility
that the use of the LED Retrofit Lights complies with applicable legal
requirements.
Some regions in the USA do not allow modified lights to be used on public
roads. Please check your local regulations before installation.
Auxbeam Products are for the whole world, non-US regions are not subject to
this regulation.
WARRANTY ATTENTION
The warranty will not apply to the following conditions:
CANbus problem: If there are flickering lights issues or light off when
installing the led light bulbs, and works when testing with DC 12V power
directly. This issue can be solved by adding a pair of CANbus.
Installation problem: Some vehicles may have an installation issue due to
narrow housing space or incorrect installation position etc. Please read the
size information on the website before purchase.
Artificial reasons: Defective led chips, chopped wire, and collars caused by
misusages. please consult your local automotive repair for assistance.
Special h7 socket: special h7 sockets for a few exclusive vehicles are
available in our store, please refer to the chart above or contact our
customer service for information.
Natural disaster: Damage because of the irresistible natural disaster like
earthquakes, floods, etc.
If purchasing from the distributor, please contact them for warranty
information.
CONTACT US
support@auxbeam.com
AUXBEAM Lighting & 15355 Manila Street, Fontana, CA 92335, USA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>