VISUAL COMFORT CHC 1140 Bernardo Medium Chandelier Instruction Manual

Bernardo Medium Chandelier
Item # CHC 1140
Instruction Manual

CHC 1140 Bernardo Medium Chandelier

NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

• Phillips Screwdriver
• Slip Joint Pliers
• Wire Strippers
• Slotted Screwdriver
• Measuring Tape
• Chain Pliers
• Wire Cutters

ASSEMBLY INSTRUCTIONS

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove collar loop (D) from chain (G) by removing quick link (H).

3. Install mounting plate (B) to the junction box and secure with mounting screws (C).

4. Secure collar loop (D) to mounting plate (B) using pliers to tighten locknut.

5. Install canopy (E) to collar loop (D) and secure with collar ring (F).

6. Determine desired overall length, and amount of chain (G) needed. Shorten chain using chain pliers. (Keep extra chain)

7. Attach chain (G) to collar loop (D) and fixture loop (I) using quick links (H). Secure quick links (H).

8. Install fixture arms (M) to center plate (N) and secure with washers (O) and lock nuts (P). (See diagram 1)
   NOTE: Check that the arms are spaced evenly before final tightening.

9. Connect all neutral wires (ribbed) from three (3) of the fixture arms (M) with jumper wire (ribbed) and fixture neutral wire (ribbed), then secure with wire nut (Q). Repeat with remaining three (3) wires on opposite side of fixture. See diagram 2.

10. Connect all hot wires (smooth with markings) from three (3) of the fixture arms (M) with jumper wire (smooth with markings) and fixture hot wire (smooth with markings), then secure with wire nut (Q).
    Repeat with remaining three (3) wires on opposite side of fixture. See diagram

12. Install metal bowl (S) to threaded nipple (R) and secure with metal ring (T).

13. Attach rubber washers (U) to either side of glass bowl (V) and install to threaded nipple (R) and secure with finial (W).

14. Thread fixture wire and ground wire through chain (G).
    NOTE: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box.

15. Separate two sides of molded wire, and strip insulation on each 5/8″.

16. Loosen collar ring (F) and let canopy (E) slip down chain (G) carefully.

17. Twist all fixture wires together. Slip through center hole of collar loop (D).
    NOTE: Untwist wires and separate to prepare for connection.

18. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 3). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A).
    NOTE: It is imperative that the fixture is grounded.

19. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).

20. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A).
    CAUTION: Do not reverse the hot and neutral connections.

21. Make sure all wire connections are tight, then carefully tuck into the junction box.

22. Install canopy (E) to collar loop (D) and secure with collar ring (F).

23. Place discs (L) and tubes (K) onto arms (M).

24. Install light bulbs into the sockets.

Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>