hd WB-NN050MD Black 6 Inches Tubular Drop Down Style Nerf Bars Running Boards Instruction Manual
- June 1, 2024
- HD
Table of Contents
hd WB-NN050MD Black 6 Inches Tubular Drop Down Style Nerf Bars Running
Boards
Product Specifications
- Compatibility: 2004-2015 Nissan Titan Crew Cab, 2017-2024 Nissan Titan Crew Cab, 2016-2024 Nissan Titan XD Crew Cab
- Part Number: WB-NN050MD / WB-NN050BD
- Material: Steel
- Finish: Black Powder Coat
- Mounting Hardware: Included
Product Usage Instructions
Parts List
- 1 Driver/Left NB1 Running Board
- 1 Passenger/Right NB1 Running Board
- 3 Driver/Left Mounting Brackets
- 3 Passenger/Right Mounting Brackets
- 12 10-1.5mm x 35mm Hex Bolts
Installation Procedure
- Start by verifying all parts are present and read the instructions carefully.
- Begin the installation at the front of the Passenger/Right side of the vehicle.
Cleaning and Maintenance
To clean the running boards, avoid using polish or wax with abrasives. Mild soap can be used for cleaning.
Frequently Asked Questions (FAQ)
Q: Can these running boards be installed on other vehicle models?
A: These running boards are specifically designed for 2004-2015 Nissan Titan Crew Cab, 2017-2024 Nissan Titan Crew Cab, and 2016-2024 Nissan Titan XD Crew Cab models. Installing them on other models may require modifications.
PARTS LIST
| 1 | Driver/Left NB1 Running Board | 12 | 10mm Nylon Lock Nuts |
|---|---|---|---|
| 1 | Passenger/Right NB1 Running Board | 12 | 8-1.25mm x 30mm Hex Bolts |
| 3 | Driver/Left Mounting Brackets | 12 | 8mm x 24mm OD x 2mm Flat Washers |
| 3 | Passenger/Right Mounting Brackets | 12 | 8mm Lock Washers |
| 12 | 10-1.5mm x 35mm Hex Bolts | 6 | 8mm Nylon Lock Nuts |
| 24 | 10mm x 27mm OD x 3mm Flat Washers |
PROCEDURE
REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
- Start installation at the front of the Passenger/Right of the vehicle and locate the factory threaded holes or stud located on the side of the inner body panel, (Figures 1 & 2). There are (4) mounting locations along the body panel. Bracket installation will use the 1st, 2nd, and 4th mounting locations.
- NOTE: Remove the plastic plug or any insulation on the side panel to locate the threaded holes.
- Select (1) Passenger/Right Mounting Bracket. Attach the Bracket to the mounting location with:
- a. Models with threaded stud : Attach the Bracket to the stud with (1) 8mm Flat Washer and (1) 8mm Nylon Lock Nut. Next, use (1) 8mm Hex Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer to attach the Bracket to the threaded insert hole on the body panel, (Figure 4). Do not tighten the hardware.
- b. Models without threaded stud: Attach the Mounting Bracket to the threaded holes with (2) 8mm Hex Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers, (Figure 3). Do not tighten the hardware.
- Repeat Steps 1 & 2 to install the center and rear Mounting Brackets.
- Carefully unwrap and select the Passenger/Right NB1 Running Board. Attach the Running Board to the front faces of the Mounting Brackets with (6) 10mm Hex Bolts, (12) 10mm Flat Washers, and (6) 10mm Nylon Lock Nuts, (Figures 4 & 5). Do not tighten hardware.
- Level and adjust the Running Board and tighten all hardware.
- Repeat Steps 1—5 to attach the Driver/Left NB1 Running Board.
- Do periodic inspections of the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Running Boards.
Passenger/Right Side Installation Pictured
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>