NETUM NT-1200 Barcode Scanner Instruction Manual
- June 1, 2024
- NETUM
Table of Contents
NETUM NT-1200 Barcode Scanner
Product Information
Specifications:
- Connection Type: RF 2.4G, Bluetooth, USB Wired
- Scanner Package Includes: Scanner, USB Dongle, USB Cable, Quick Setup Guide
- Firmware Version: V1.6.30
Product Usage Instructions
Connection Way:
The scanner can transmit data to your device via Bluetooth or 2.4G
Wireless. Follow the steps below to start scanning:
- For 2.4G Wireless Channel:
- Plug the USB dongle into your device.
- Power on the scanner.
- Setup keyboard language (Default: US keyboard).
- To switch from Bluetooth to wireless transmit, scan “Wireless transmit” and repeat steps (a) and (b).
USB HID-KBW Feature:
When the dock connects to your device via USB cable, USB HID-KBW feature is
enabled by default. The scanner’s transmission will simulate USB keyboard
input without requiring a driver.
USB COM Port Emulation:
By scanning USB COM Port Emulation, your device can receive data as a serial
port does when connected via USB cable. Note: A driver is required for this
feature.
Bluetooth Transmit:
- Power on the scanner.
- Scan “Bluetooth Transmit.”
- Remove pairing information from devices when changing transmit mode.
Keyboard Language:
To set the keyboard language, scan the appropriate command barcode based on
your keyboard type (eg, English, French, German).
Working Mode:
If you are outside Bluetooth signal range, activate store mode to buffer
scanned data for manual upload later near the working device.
Package Included
- 1PC * Scanner
- 1PC * USB Dongle
- 1PC * USB Cable
- 1PC * Quick Setup Guide
Firmware Version:
(1) Firmware version will be displayed by scanning “$SW#VER”.
Factory Defaults
Scanning the following barcode can restore the engine to the factory defaults.
Barcode Programming
Netum barcode scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide. An asterisk (*) next to an option indicates the default setting.
Important Notes
Some command barcodes only work in a particular connection mode. Pay attention to below symbols when you scanning command barcodes.
- Command barcodes only apply to scanner work via Bluetooth.
- Command bacodes only apply to scanner work via 2.4G Wireless.
Connection Way
Scanner transmits data to your device via bluetooth or 2.4G Wireless. You can choose either way to start scanning.
How to transmit data via 2.4G Wireless Channel ?
- Get Started:
1. Plug the USB dongle into your device.
2. Power On the scanner
3. Setup keyboard language: US keyboard was set by default. If you use other type of keyboard please refer to Keyboard language.
4. If you want to change bluetooth transmit to wireless transmit, you will have to scan “Wireless transmit” then follow step (1) and (2) to complete the confiigurations.USB HID-KBW
When the dock connects with your device via USB cable, USB HID-KBW feature
will be enabled by default. Scanner’s transmission will be simulated as USB
key-board input. It works on a Plug and Play basis and no driver is required.
USB COM Port Emulation
When the dock connects with your device via USB cable, by scanning “USB COM
Port Emulation” will allow your device to receive data in the way as a serial
port does.
Note: A driver is required for this feature.
How to transmit data via bluetooth ?
- Get Started:
1. Power on scanner.
2. Scan “Bluetooth Transmit”.
3. Make sure the device is in range with Bluetooth turned on.
4. Pressing the scan button will initiate the attempts to connect.
5. If a connection is made, the blue light will stop blinking and turn solid.
6. If a connection is not made after several attempts, the scanner will emit a long beep (and the blue light will turn off).
7. Bluetooth working channel is not set by default.If you want to connect via bluetooth, you will have to scan “Bluetooth Transmit” before pairing.Basic Mode (HID) (default)
- NO software installation needed
- Connects to most devices
- Scanner interacts with host device like a keyboard
Application Mode (Apple Specifiic Serial Profile)
- For iOS Devices
- If you have an iOS application that supports our Scanners this is the mode to use
Applicatin Mode (Serial Port Profiile)
- For Android or Windows
- Software installation is required
- If you have an application that supports this is the mode recommended
Important Notes:
Remove the pairing information both from devices-host PC/phone and the scanner
when you change the data transmit mode.
Bluetooth Transmit Speed
By scanning the appropriate barcode below will change the bluetooth transmit
speed.
Keyboard Language
For example If you use French Keyboard, scan command barcode of “French
keyboard”. If you use a US keyboard you can ignore this step.
Working Mode
If you are heading for a working area which lies outside the Bluetooth signal
range, you may activate scanner’s store mode, following steps described below.
Under this mode, all scanned data will be stored directly into the buffer
memory of the device. Furthermore, data entries will be permanently saved in
the buffer memory prior to the manual upload into the working station, so that
you may upload them when you are near your working device.
Idle Time
Time period set for scanner from idle to sleep. Default Idle Time: 3mins
.
Convert Case
Beep Volume
By scanning the appropriate barcode below will change the beep volume.
Function Key Mapping
When Function Key Mapping is enabled, function characters are sent over the
keypad.
FAQ
Q: What should I do if I need to configure more settings?
A: Download additional configurations from the official website:
https://www.netum.net/
Are there any barcodes for applying or removing prefix & suffix ?
Yes, you may go to our official website”
www.netum.net” to download the manual, refer to the
section of “prefix and suffix” or turn to customer service for help.
How can I restore the scanner to factory defaults?
Scan the barcode provided in the manual to restore the engine to factory defaults.
How do I change the Bluetooth transmit speed?
Scan the corresponding barcode to change the Bluetooth transmit speed to High, Medium (default), or Low speed.
Some barcodes cannot be read, why ?
a. Dirty or unclear barcodes might not be read. b. The possible reason is that setting for some barcode types not commonly used is off by default. You need to activate a specifiic barcode type to get it to work. Please contact us for help.
How to change terminator to TAB ?
Please refer to the section of “Terminator Configuration” from the manual downloaded from our official website.
How to solve the messy code problem encountered while using other foreign languages?
The default language is English. Please refer to “Keyboard Language” to change the language.
Why scanner can not read Italy Pharmacy code?
Why scanner can not read add-on 2 or 5 codes?
Download the manual from our official website according to the scanner model nunber, refer to the section of ADD-On code and scan the appropriate command barcode to enable the scanner read it.
Why scanner can not read datamatrix GS1 in a correct format ?
Scan “Enable Funtion Key Mapping” from this manual will enable scanner to output group separator.
Note: Please do not hesitate to contact us if you need any other configurations.
Contact Information
Tel.: +0086 20-3222-8813
Whatsapp: +86 136 222 33 974
Email: service@netum.net
Website: www.netum.net
Addr.:Room 301, 6th Floor and full 3rd Floor, Building 1, No. 51
Xiangshan Avenue, Ningxi Street, Zengcheng District, Guangzhou City, Guangdong
Province, China Made in China
EU Name: Apex CE Specialists GmbH
Add: Habichtweg 1 41468 Neuss Germany
UK Name: APEX CE SPECIALISTS LIMITED
Add: 89 Princess Street, Manchester, M1 4HT, UK
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Any Changes or modifications not expressly approved by the party responsible le for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
References
- NETUM | Barcode Scanner | Thermal Printer | PDA Terminal Device
- NETUM | Barcode Scanner | Thermal Printer | PDA Terminal Device
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>