NETUM DS7100 Wired 2D QR Barcode Scanner User Guide
- June 5, 2024
- NETUM
Table of Contents
- NETUM DS7100 Wired 2D QR Barcode Scanner
- Quick Setup Guide
- Barcode Programming
- Communication Mode
- Keyboard Language
- Scanning Mode
- Default Configuration
- Symbologies
- Interleaved 2 of 5
- Codabar
- MSI/MSI PLESSEY
- ISSN
- GS1 DataBar/RSS
- ID Inverse barcode
- 2D Symbologies
- QR
- Data Matrix(DM)
- Maxi Code
- Aztec Code
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
NETUM DS7100 Wired 2D QR Barcode Scanner
Quick Setup Guide
This is 1D&2D plug and play model if you use a US keyboard. If you use other type of keyboard, plug the USB cable on your device , setup keyboard language before you use it. After that the scanner can start to work.
Barcode Programming
Netum barcode scanners are factory programmed for common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide. An asterisk (*) next to an option indicates the default setting.
Communication Mode
USB -KBW
When you connect the scanner to the Host via a USB connection, you can enable
the USB-KBW feature by scanning the barcode below. It works on a Plug and Play
basis and no driver is required.
USB COM
If you connect scanner to the Host via a USB connection, the USB COM Port
Emulation feature allows the Host to receive data in the way as a serial port
does.
Keyboard Language
In order to let scanner upload the codes in a correct way, you have to set the keyboard language. For example If you use French Keyboard, scan below barcode of “French keyboard” then scanner will upload barcodes according to France keyboard layout. American Keyboard is set by default, if you use a US keyboard you can skip this step.
Scanning Mode
Key Holding
Press the button to trigger the reading, release the button to end the
reading. Reading success or reading time over a single reading time will end
the reading
Continuous Mode
Under continuous mode scanner performs continuous work. Reading success or
reading time over a single reading time will end the reading. More than the
specified time will automatically trigger the next reading.
Auto Sense Mode
Under auto sense mode, scanner detects the brightness of the surroundings.
Trigger reading when the brightness changes. Reading success or reading time
over a single reading time will end the reading. Regardless of the last
success or failure to read, re-enter the detection of the surrounding
environment brightness.
Terminator configuration
The scanner provides a shortcut for setting the terminating character suffix
to CR or CRLF and enabling it by scanning the appropriate barcode below.
Beeper Volume
To select a decode beep volume, scan the appropriate bar code.
Mute
To enable or disable close all prompt, scan the appropriate bar code below.
Default Configuration
If you want to cancel all the configuration that you have done to the scanner. Scan below barcodes to the restore factory.
Symbologies
Add-On Code
An EAN/UPC barcode can be augmented with a two-digit or five-digit add-on code
to form a new one. In the examples below, the part surrounded by blue dotted
line is an EAN-8 barcode while the part circled by red dotted line is add-on
code.
Interleaved 2 of 5
Enable/Disable Interleaved 2 of 5
To enable or disable Interleaved 2 of 5, scan the appropriate bar code below.
Note: Interleaved 2 of 5 with the length of 14 digits by default, if you have other length please scan “Any length”
Codabar
Enable/Disable Codabar
To enable or disable Codabar, scan the appropriate bar code below.
MSI/MSI PLESSEY
Enable/Disable MSI
To enable or disable MSI, scan the appropriate bar code below.
ISSN
Enable/Disable ISSN
To enable or disable ISSN, scan the appropriate bar code below.
GS1 DataBar/RSS
Enable/Disable GS1 DataBar-14
To enable or disable GS1 DataBar-14, scan the appropriate bar code below.
Enable/Disable GS1 DataBar Limited
To enable or disable GS1 DataBar Limited, scan the appropriate bar code below
.
Enable/Disable GS1 DataBar Expanded
To enable or disable GS1 DataBar Expanded, scan the appropriate bar code below
.
ID Inverse barcode
Normal barcode – White background and black bars
Reverse barcode- Black background with white bars
2D Symbologies
PDF417 Enable/Disable PDF417
To enable or disable PDF417, scan the appropriate bar code below.
Reverse PDF417 Code
QR
Enable/Disable QR
To enable or disable QR, scan the appropriate bar code below.
Reverse QR Code
Data Matrix(DM)
Enable/Disable Data Matrix(DM)
To enable or disable Data Matrix(DM), scan the appropriate bar code below.
Reverse Code
Maxi Code
Enable/Disable Maxi Code
To enable or disable Maxi Code, scan the appropriate bar code below.
Aztec Code
Enable/Disable Aztec Code
To enable or disable Maxi Code, scan the appropriate bar code below.
Note: If you want other programmings which is not available in this manual, please do not hesitate to contact us: service@netum.net
Support For any inquiries concerning our products, please send an email to
service@netum.net, and we will respond to you as
soon as possible.
Contact Information
Tel.: +0086 20-3222-8813
Email: service@netum.net
Whasapp: +86 188 2626 1132
Addr.:Room 301, 6th Floor and full 3rd Floor, Building 1, No. 51 Xiangshan
Avenue, Ningxia Street, Zengcheng District, Guangzhou, Guangdong, China/
511356
Website: https://www.netum.net/
Name: APEX CE SPECIALISTS LIMITED
Add: UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK, NEW MALLOW
ROAD,CORKT23 AT2PIRELAND Contact: Wells
Tel: +353212066339
E-Mail: Info@apex-ce.com
Made in China