NETUM RS-8000 Bluetooth Ring Scanner User Manual

NETUM RS-8000 Bluetooth Ring Scanner User Manual

Package Included:

1 x Scanner; 1 x Dock;
1 x USB cable; 2 x Batteries;
1 x Quick Manual;

Product Information

1. Scanning Window
2. Scanner LED
3. Battery Door
4. Buzzer
5. Trigger Button
6. Adjustable Ring Belt

1. Battery Charging Dock
2. DC  Port
3. Type C Port
4. Bluetooth LED
5. Transmission LED
6. Battery charging LED
7. Scanner Power charging LED

Charge The Battery

1. Press and push up the battery door
   

2. Insert battery and secure battery door
   

Scanner’s Bluetooth Connection Status

1. Solid Blue- Bluetooth  Connected
2. Flashing Blue- Bluetooth Disconnected/Bluetooth Pairing

Battery Dock LED Status:

1. Scanner LED
2. Solid Red- Full Charged
3. Flashing Red- Charging
4. Battery LED
5. Solid Red- Full Charged
6. Flashing Red – Charging
7. Transmission LED
8. Solid Green- No Transmit
9. Flashing Green- Transferring data
10. Bluetooth connection status
11. Solid Blue- Scanner has connected with the dock
12. Flashing Blue- Scanner has disconnected with the dock

Setup Guide

Get Started

1. Pair Netum bluetooth (refer to the section of “Bluetooth pairing”)
2. Setup keyboard language: US keyboard is set by default. If you use other type of keyboard please refer to the section of “keyboard language”.
3. Locate cursor on place where you want the data to be displayed after that you can start to scan.

Firmware Version
Read below command barcode to check scanner firmware version.

Firmware Version

Barcode Programming
Netum barcode scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in thism guide. An asterisk (*) next to an option indicates the default setting.

Bluetooth Pairing

How to pair scanner’s bluetooth with the dock ?

1. Connect the dock with your computer via USB
2. Scan QR code from the dock, Bluetooth paired once blue LED on the dock turns to solid blue.
3. If you want to disconnect it with the dock and connect it with your device, scan “Bluetooth HID” then pair Netum Bluetooth.

Bluetooth HID (Default)

Important Note:
Default Idle Time: Scanner will power off automatically if device is not connected in 3mins . If you want BLE and SPP mode, please contact us.

Keyboard Language
For example If you use French Keyboard, scan command barcode of “French keyboard ”. If you use a US keyboard you can ignore this step.

America EN keyboard

French keyboard

Germany keyboard

Italy keyboard

Portugal keyboard

Spain keyboard

UK keyboard

Czech keyboard

Hungary keyboard

Belgium FR keyboard

Data Uploading Mode
If you are heading for a working area which lies outside the bluetooth signal range, you may activate scanner’s store mode, following steps described below. Under this mode,all scanned data will be stored directly into the buffer memory of the device. Furthermore, the data entries will be permanently saved in the buffer memory prior to the manual upload into the working station, so that you may upload them when you are near your working device.

By scanning the following barcode, the device leaves the offline mode, normal mode will be reinitialised.

*Quit Offline Mode

Offline Mode
By scanning the following barcode, the offline mode will be activated.

Offline Mode

Output Stored Data
By scanning the following barcode, all data entries in the buffer memory can be manually uploaded after reconnecting to the working station.

Output Stored Data

Output Total Entry
By scanning the following barcode, the gross quantity of the uploaded data entries will be summarised .

Output Total Entry

Clear Memory
By scanning the following barcode, all data in the buffer memory will be deleted.

Clear Memory

Get Battery Volume
Scan below command barcode to get battery rough volume.

Battery Rough Volume

1. Voltage < 3.5V, Low battery Volume, there will have 5 beeps after each scan. Scanner can not be able to read any barcodes.
2. 3.7V< Voltage < 3.5V, Low battery Volume, there will have 2 beeps after each scan. Scanner still be able to read barcodes.
3. Voltage >4.2V, Full Volume

Idle time
Scanner will turn to sleep after idle/inactive for 1min Scan “Disable module Idle time” before you doing any other setup from this section.

Power Off

Disable Sleep Mode

• 3mins
  
  1Hour
  

10S Keyboard POP UP/HIDE
During the scanning 10S keyboard can be hided or popped up by scanning below command barcode.

1. Scan this barcode at Bluetooth HID connected state on I0S device, popup 10S keyboard.
   10S Keyboard POP UP/HIDE
   

2. Popup 10S keyboard by hold trigger 4 seconds.
   Enable/Disable
   

3. Popup 10S keyboard by double click trigger.
   Enable/Disable
   

Note: Two short beeps after scan indicates disable, one long sound with three tones indicates enable.

Beeper
Enable/Disable scanner to beep to indicate successful scan.

Beep Off

High Volume

Middle Volume

Low Volume

Vibration
Scan the appropriate barcode below to enable or disable the vibration.

Disable the Vibration

Enable the Vibration

Factory Restore
Scan below command barcode will reset the scanner.

Factory Restore

Beep Tone Indication

Mode Transmission failed
Five Beeps in Same Tone| Fai| to power on due to low battery volume

FAQ

Problem: Some Barcodes Cannot be read. Solution:

1. Dirty or unclear barcodes might not be read.
2. The possible reason is that setting for some barcodes types are not commonly used is off by default. You need to activate a specific barcode type to get it to work. Please contact us for help.

Question: Is there any barcodes for applying or removing suffix?

Yes. Please turn to customer service for help.
Question: How to solve the messy code problem encountered while using other foreign languages?

Solution:

Default language is English. If you use other types of keyboard please refer to “Keyboard language”, see page 5.

Problem: Barcodes can be read but can not be displayed

Solution :
a. Please verify if your scanner is on a store mode.
b. Contact us to get command barcode for configuring the baud rate.

Question:2D scanner can not output Datamatrix GS1 group separator?
Solution:
Please contact the service team for help, they will send you command barcode to enable the scanner output group separator.

Support
For any inquiries concerning our products, please send an email to service@netum.net, and we will respond to you as soon as possible.

Contact Information
Whatsapp: +86 188 2626 1132
Tel.:+0086 20-6626-0708
Email: service@netum.net
Website: www.netum.net
Addr.: Unit 137, The Pacific Industry Park, Xintang Town,Zengcheng District, Guangzhou,China/511340

Made in China
Name: APEX CE SPECIALISTS LIMITED
Add: UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK, NEW MALLOW ROAD,CORK,T23 AT29, IRELAND
Contact: Wells
Tel:+353212066339
E-Mail : Info@apex-ce.com

RF exposure statement This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.—
  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>