dji C10000 Intelligent Power Supply User Guide

: June 1, 2024
: DJi

Table of Contents

dji C10000 Intelligent Power Supply
Product Information
Disclaimer
In the Box
Introduction
Activation
Updating Firmware And Maintenance
Specifications
FCC Statement
More Information
Read User Manual Online (PDF format)
Download This Manual (PDF format)

dji C10000 Intelligent Power Supply

Product Information

Specifications

Product Name: C10000 Intelligent Power Supply
Version: v1.0
Features: Overcurrent protection, overcharging protection, overvoltage and undervoltage protection, overheating protection, status display

FAQ

Q: Can I charge multiple devices simultaneously with this power supply?
- A: The power supply is designed to charge one device at a time for optimal performance and safety.
Q: How often should I clean the dustproof cover?
- A: It is recommended to clean the dustproof cover regularly, at least once a month, to ensure proper cooling efficiency.

Disclaimer

Congratulations on purchasing your new DJITM product. Read this entire document and all safe and lawful practices DJI provided carefully before use. Failure to read and follow instructions and warnings may result in serious injury to yourself or others, damage to your DJI product, or damage to other objects in the vicinity. By using this product, you hereby signify that you have read this document carefully and that you understand and agree to abide by all terms and conditions of this document and all relevant documents of this product. You agree to only use this product for proper purposes. You agree that you are solely responsible for your own conduct while using this product and for any consequences thereof. DJI accepts no liability for damage, injury, or any legal responsibility incurred directly or indirectly from the use of this product.

DJI is a trademark of SZ DJI TECHNOLOGY CO., LTD. (abbreviated as “DJI”) and its affiliated companies. Names of products, brands, etc., appearing in this document are trademarks or registered trademarks of their respective owner companies. This product and document are copyrighted by DJI with all rights reserved. No part of this product or document shall be reproduced in any form without the prior written consent or authorization of DJI. This document and all other collateral documents are subject to change at the sole discretion of DJI. This content is subject to change without prior notice. For up-to-date product information, visit www.dji.com and go to the product page for this product.

Warning

Read these instructions carefully before use. Failure to follow the relevant instructions may result in property damage, personal injury, or death. The warnings and precautions in this manual do not cover all possible situations and the user must practice common sense in relation to the product that is not mentioned in this manual and maintain a cautious attitude.
Only qualified electricians wearing insulated gloves can perform the fast charging connection.
When using the fast charging connection, the input current required by the power supply exceeds 16 A.DO NOT connect the fast charging cables to 16A or 10A power outlets. DO NOT use the fast charging cables indoors.
DO NOT use two slow charging cables simultaneously indoors.
DO NOT use the fast charging cable together with the slow charging cable.
When using the C10000 Intelligent Power Supply with a mains power supply for fast charging, make sure to connect the power supply to a three-phase five-wire industrial power supply that has a rated output of 18 kW or above.
To use the C10000 Intelligent Power Supply with a third-party generator, make sure to purchase a single-phase generator that has a rated voltage of 220 V and rated output of 12 kW or above.
To disconnect or reconnect the connector between the DC module and the AC module, disconnect the power supply from power source first. DO NOT perform this operation while the power supply is running.
DO NOT use the power supply under direct sunlight, during a thunderstorm, or in other wet environments.
The power supply should be kept in an environment with a temperature range of 23° to 104° F (-5° to 40° C).
Keep the power supply away from heat, pressure, water, flammable gases, and corrosives.
Keep the power supply away from inflammable materials while charging. DO NOT place the power supply or charging batteries on a blanket or any carpeted surfaces when in use.
Place the power supply on a flat and stable surface. In order to prevent fire hazards, make sure the device is properly insulated and that there is at least 50 cm of space for ventilation.
DO NOT use the power supply in an area where batteries are stored. There should be a distance of at least 30 cm between the power supply and any charging batteries. Otherwise, the power supply or charging batteries may be damaged by excessive heating and may even lead to a fire hazard.
Refer to the user guide of the batteries for more safety instructions before use.
In case of fire, use a dry powder fire extinguisher. A liquid fire extinguisher may lead to an electrical hazard.
DO NOT unplug the AC power cables or charging cable while the power supply is in use. Remove the batteries after charging is completed.
If there is any noticeable buildup on the charging cable connector, clean it up at the earliest possible opportunity. Make sure the power supply is not connected to power before cleaning.
DO NOT move or carry the power supply by pulling the charging cable. Otherwise, the charging cable may be damaged.
Handle the charging cable with care to avoid damage from strong impact.
The dustproof cover should be cleaned regularly to ensure the cooling effect of the fans.
Use the DJI RC Plus remote controller to activate the power supply and update firmware. Before activation or firmware updates, make sure that the remote controller has been updated to the latest firmware.

In the Box

dji-C10000-Intelligent-Power-Supply-fig-1

The slow charging cable is packaged in a separate box. The type of slow charging cable may vary depending on the country or region. The illustration may differ from the actual product.

Introduction

The C10000 Intelligent Power Supply supports both fast and slow charging and can connect with one Intelligent Flight Battery. For compatible batteries, see the Specifications section.

While charging, the power supply monitors the status of the battery and can automatically adjust the charging current if required. The intelligent power adjustment function ensures charging can continue even if the ventilation holes are blocked. The power supply also boasts a self-diagnostics function. Users can check the status LEDs to confirm if there are any errors. For more detailed information regarding any errors, users can connect the power supply to a remote controller using a USB-C cable and launch the DJI Agras app. Additionally, the power supply includes overcurrent protection, overcharging protection, overvoltage and undervoltage protection, overheating protection, and status display.

Overview

dji-C10000-Intelligent-Power-Supply-fig-2

Charging Cable
Status LEDs
Dustproof Cover
Handle
Ventilation Holes
Main AC Power Port
Auxiliary AC Power Port
Cable Storage Cover

Status LEDs

Charging Channel Status LED
DC Module Status LED
Generator (excl. DC Module)/AC Module Status LED
USB-C Connector Cover

Status LED	Blinking Pattern	Description

Charging Channel Status LED

| Solid yellow| The power supply is ready to connect to a battery
Blink green once continuously| Charging
Solid green| Fully charged
Blink yellow once continuously| Warning for the battery/charging channel
Blink red once continuously| Battery/charging channel error

DC Module Status LED

| Blink yellow four times continuously| DC module is not activated
Blink yellow once continuously| Warning for the DC module
Blink red once continuously| DC module error

Generator (excl. DC Module)/AC Module Status LED

| Blink yellow four times continuously| Generator (excl. DC Module)/AC module is not activated
Blink yellow once continuously| Warning for the generator (excl. DC Module)/ AC module
Blink red once continuously| Generator (excl. DC Module)/AC module error
Blink red four times continuously| Generator (excl. DC Module) maintenance is required

Warning

dji-C10000-Intelligent-Power-Supply-fig-4

When the status LEDs blink for warning or error, connect the power supply to the remote controller using a USB-C cable to see more information.
If any part of the power supply is abnormal or damaged, it is recommended to contact a DJI-authorized dealer or DJI Support to repair or replace the part.

Activation

The intelligent power supply must be activated before using for the first time. Connect the remote controller to the internet first. Use a USB-C cable to connect to the USB-C connector of the power supply and the USB-A connector of the remote controller. Run the DJI Agras app on the remote controller and tap Device Management > Charging Device to activate the power supply.

Using the Intelligent Power Supply

The C10000 Intelligent Power Supply supports both fast and slow charging. Different power cables are required to connect to qualified power supplies when using different charging methods.

Fast Charging Method 1: Use two fast charging cables to connect the power supply to a three-phase-five-wire industrial power supply that has a rated output of 18 kW or above.
Fast Charging Method 2: Use two fast charging cables to connect the power supply to a third-party single-phase generator that has a rated voltage of 220 V and rated output of 12 kW or above.
- Warning: To use the power supply with a third-party generator for fast charging, connect the hot wires (labeled L), neutral wires (labeled N), and ground wires (labeled PE) of the power supply to a hot terminal, neutral terminals, and ground terminals of the generator respectively. Make sure to connect the two hot wires to the same hot terminal. Refer to the user manual of the generator for other specific usages.
Slow Charging: Use a slow charging cable with the conversion cable to connect the power supply to a power outlet.

The following will describe the detailed steps of charging the intelligent flight battery using fast charging (take fast charging method 1 as an example) and slow charging.

Fast Charging

Turn off the air circuit breaker for the three-phase AC power supply.
Take out the safety pins from the fast charging cables, connect the cables to the power supply, and insert the safety pins back in place.
- After connecting the fast charging cables to the power supply, make sure to insert the safety pins back into place to avoid damage caused by a loose connector.
Connect the two fast charging cables to a three-phase-five-wire industrial power supply:
Connect the hot wires (labeled L), neutral wires (labeled N), and ground wires (labeled PE) of the fast charging cables to the hot terminals, neutral terminal, and ground terminal of the three-phase power supply, respectively. Make sure to connect the two hot wires to different hot terminals.
- Only qualified electricians wearing insulated gloves can perform the fast charging connection.
- When using the fast charging connection, the input current required by the power supply exceeds 16A. DO NOT connect the fast charging cables to 16A or 10A power outlets.
Turn on the air circuit breaker of the three-phase AC power supply.
Connect the power supply to the battery. To charge the DB1560/T40 Intelligent Flight Battery, connect the charging cable to the air-cooled heat sink before putting the battery into the heat sink. The power supply starts to charge the battery. The four LEDs of the battery blink in sequence while charging. Remove the battery when the four LEDs turn solid or off and put another battery inside the heat sink to charge.
When charging is finished, turn off the air circuit breaker before disconnecting the fast charging cables from the power supply.

Slow Charging

Warning

The type of the power outlet may vary depending on the country or region. Choose the appropriate power outlet accordingly.
DO NOT use two slow charging cables simultaneously indoors.

Take out the safety pins from the conversion cable, connect the conversion cable to the main AC power port of the power supply, and insert the safety pins back in place.
- After connecting the conversion cable to the power supply, make sure to insert the safety pins back into place to avoid damage caused by a loose connector.
Connect the slow charging cable with the conversion cable, and then connect to a power outlet.
Connect the power supply to the battery using the same method d escribed in the Fast Charging section.
When charging is finished, disconnect the slow charging cable from the power outlet and then disconnect the conversion cable from the power supply.

Updating Firmware And Maintenance

Updating Firmware

There will be notifications when firmware updates are available on the DJI website. Pay attention to the Download page of the product on the DJI website to get the latest firmware. Follow the instructions below to update the firmware of the power supply using the remote controller.

Connect the remote controller to the internet and then connect the power supply to the remote controller using a USB-C cable.
Run the DJI Agras app on the remote controller and update the firmware by following the instructions.

Storage And Maintenance

Storage

When you are not using the power supply, disconnect the power supply from AC power and disconnect the charging cable from the battery. Place the power supply in a stable place.

DO NOT place the power supply under direct sunlight or in rain or other wet environments.
Keep the power supply away from heat, pressure, water, flammable gases, and corrosives.

Maintenance

Clean the dustproof cover regularly to ensure the heat dissipation performance.

Remove the four screws and remove the dustproof cover.
Clean the dustproof cover and install it back in place. Install the four screws to secure the dustproof cover.

Specifications

Model Number: CSX702-9500
Operating Temperature: -5° to 40° C (23° to 104° F)
Output Channel: 1
Input/Output
- Input (Main): 220-240 VAC, 50/60 Hz, 24 A MAX
- Input (Auxiliary): 220-240 VAC, 50/60 Hz, 24 A MAX
- Output: 59.92 VDC MAX, 175 A MAX, 9000 W MAX
- Input (Main): 100-120 VAC, 50/60 Hz, 16 A MAX
- Input (Auxiliary): 100-120 VAC, 50/60 Hz, 16 A MAX
- Output: 59.92 VDC MAX, 60 A MAX, 3000 W MAX
Compatible Battery: DB1560/DB800/T40/T30/T20P Intelligent Flight Battery
Dimensions: 400 × 266 × 120 mm
Weight: Approx. 11.4 kg

FCC Statement

Supplier’s Declaration of Conformity

Product name: C10000 Intelligent Power Supply
Model Number: CSX702-9500
Responsible Party: DJI Research LLC
Responsible Party Address: 435 Portage Ave, Palo Alto, CA 94306
Website: www.dji.com

We, DJI Research LLC, being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference
This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

ISED Compliance

CAN ICES-003 (A) / NMB-003(A)

EU & UK Compliance Notice

EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (C10000 Intelligent Power Supply) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/35/EU.

A copy of the EU Declaration of Conformity is available online at www.dji.com/eurocompliance
EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (C10000 Intelligent Power Supply) is in compliance with the essential requirements and other relevant provisions of Electrical Equipment (Safety) Regulations 2016.

A copy of the GB Declaration of Conformity is available online at www.dji.com/eurocompliance

Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

BSMI Compliance Notice

Device name: Switching power supply, model (type): CSX702-9500

Unit

| Restricted substances and their chemical symbols
Lead (Pb)| ****

Mercury (Hg)

| ****

Cadmium (Cd)

| Hexavalent chromium (Cr+6)| Polybrominated biphenyls

(PBB)

| Polybrominated diphenyl ethers (PBDE)
circuit board| －| ○| ○| ○| ○| ○
shell| ○| ○| ○| ○| ○| ○
AC input socket| ****

○

| ****

○

| ****

○

| ****

○

| ****

○

| ****

○

Pin| ○| ○| ○| ○| ○| ○
Remarks 1. “Exceeding 0.1 wt %” and “Exceeding 0.01 wt %” mean that the percentage content of restricted substances exceeds the percentage content reference value.

Remarks 2. “○” means that the percentage content of the restricted substance does not exceed the percentage content benchmark value. Remarks 3. “-” means that the restricted substance is an excluded item.