VOLLRATH 39737N Cafeteria Breath Guard Instruction Manual
- June 1, 2024
- VOLLRATH
Table of Contents
VOLLRATH 39737N Cafeteria Breath Guard
Product Information
Specifications
- Product Name: Cafeteria Breath Guard
- Types: One Piece and Three Piece
- Manufacturer: Vollrath Company, L.L.C.
- Item No.: 2350030-01
Product Usage Instructions
One Piece Breath Guard Installation
- Ensure the breath guard is included in the shipment.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figure 1. Repeat for all four uprights.
Three-Piece Breath Guard Installation
- Ensure the breath guard is included in the shipment.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C). Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
These instructions cover the installation of the one pice Cafeteria Breath Guard and the three piece Cafeteria Breath Guard.
One Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C)
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side. three Piece Breath Guard installation.
Three Piece Breath Guard installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
Technical Services
The Vollrath Company, L.L.C. 1236 North 18th Street Sheboygan, WI 53081-3201
U.S.A.
Main Tel: 800.628.0830 Service Tel: 800.628.0832 FAX: 800.752.5620
Vollrath of Canada, Co.
Tel: 800.695.8560
FAX: 800.752.5620
© 2010 The Vollrath Company, L.L.C.
FAQ
Q: What should I do if I overtighten the cap nuts during installation?
A: Overtightening may cause the plastic to crack. If you encounter this issue, stop immediately and contact customer service for assistance.
Q: Can I disassemble the breath guard for cleaning?
A: Yes, you can disassemble the breath guard following the installation steps in reverse order. Ensure to clean each component thoroughly before reassembling.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>