VOLLRATH 38734 Cafeteria Breath Guard Instruction Manual
- June 1, 2024
- VOLLRATH
Table of Contents
VOLLRATH 38734 Cafeteria Breath Guard
Product Information
Specifications :
- Product Name: Cafeteria Breath Guard
- Model: One Piece and Three Piece
- Manufacturer: Vollrath Company, L.L.C.
- Item No.: 2350030-01
Product Usage Instructions
One Piece Breath Guard Installation:
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figure 1.
- Repeat the above step for all four uprights.
Three Piece Breath Guard Installation:
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C).
- Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) at all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing with cap nuts (C).
- Repeat the above steps for all mounting locations.
FAQ :
-
Q: What should I do if I accidentally crack the plastic while tightening the cap nuts?
A: If you accidentally crack the plastic, contact Vollrath Company’s Service Tel at 800.628.0832 for assistance on replacement parts. -
Q: Can I adjust the height of the breath guard?
A: The height of the breath guard can be adjusted during installation by positioning the uprights at different heights on the studs.
Installation Instructions
One Piece cafeteria Breath Guard three Piece cafeteria Breath Guard
These instructions cover the installation of the one pace Cafeteria Breath
Guard and the three piece Cafeteria Breath Guard.
One Piece Breath Guard installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
Three Piece Breath Guard installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
Item No. 2350030-01 Rev 04/12
- The Vollrath Company, L.L.C. 1236 North 18th Street Sheboygan, WI 53081-3201 U.S.A.
- Main Tel : 800.628.0830
- Service Tel : 800.628.0832
- FAX : 800.752.5620
- Vollrath of Canada, Co.
- Tel : 800.695.8560
- FAX : 800.752.5620
- © 2010 The Vollrath Company, L.L.C.
- www.vollrathco.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>