nedis PIM15012EGY Modified Sine Wave User Guide

nedis PIM15012EGY Modified Sine Wave

Product Specifications

• Model: Power Inverter (150 Watt)
• Model Numbers: PIM15012EGY, PIM15012FGY
• Output: 230 V AC
• Input: 12 V DC
• Waveform: Modified Sine Wave
• Maximum Load: 80% for long use (>1 hour)
• USB Port : Yes
• Intended Use : Powering socket and USB devices
• Compatibility: Class II devices

Product Usage Instructions

Powering a Socket Device

1. Make sure the target device is switched off before connecting it.
2. Plug the power plug from a target device into the power socket A1.
3. Set the power switch A3 to ON.
4. Do not load the power inverter more than 80% during long use (>1 hour).

Powering a USB Device

1. Plug a USB cable into the USB port A2 of the power inverter.
2. Plug the other end of the USB cable into your target device.
3. Set the power switch A3 to ON.

Troubleshooting

If the target device is not receiving power, follow these steps:

• Check if the power inverter is switched on.
• If the 12 Volt power socket is not working, try a different one.
• If the fuse has blown due to excessive power draw, follow the steps to replace it.

Safety Instructions

• Do not attempt to power the same target device again if an issue occurs.
• Dispose of the product at an appropriate collection point; do not dispose with household waste.
• Keep the product away from direct sunlight and out of reach of children.
• Avoid using the product with precision measuring equipment or for professional use.

FAQ

• Q: Can I use this power inverter with devices that have motors?
  • A : It is recommended to use a pure sine wave power inverter for devices with motors as modified sine wave inverters may be less suitable.
• Q: What should I do if my target device is not receiving power?
  • A : Check if the power inverter is switched on, try a different 12 Volt power socket, and ensure the fuse has not blown due to excessive power draw.
• Q: Is this product suitable for outdoor use?
  • A : No, this product is intended for indoor use only. Avoid exposing it to direct sunlight.

Quick start guide

Power Inverter (150 WaTT)

PIM15012EGY

PIM15012FGY

For more information see the extended manual online: ned.is/pim15012egy

Intended use

This product is a power inverter to convert 12 V DC to 230 V AC. 4 The modified sine wave power inverters are less suitable for devices with a motor. Use a pure sine wave power inverter (PIPxxxxxGY).
Only use this product in combination with class II devices.

Do not use this product with:

• Devices that exceed the rated power of the inverter.
• Capacitive and perceptual load devices such as air conditioning, high power drills, fridges, microwave ovens, or blenders.
• Devices that have strict power supply requirements, such as precision measuring equipment.

The product is intended for indoor use only. Any modification of the product may have consequences for safety, warranty and proper functioning. The product is not intended for professional use.

Main parts (image A)

1. Power socket
2. USB port
3. Power switch
4. Fuse
5. 12 Volt plug

Safety instructions

WARNING

• Ensure you have fully read and understood the instructions in this document before you install or use the product. Keep the packaging and this document for future reference.
• Only use the product as described in this document.
• Do not install the product next to flammable materials.
• Do not place the product in areas with high temperature or direct sunlight.
• Do not cover or obstruct the ventilation openings on the product.
• Do not immerse the product in water or other liquids.
• Do not expose the product to water, rain, moisture, or high humidity.
• Do not operate the product close to combustible gas or open fire.
• Do not operate appliances that may feed power back into the power inverter.
• Do not open the product, there are no user-serviceable parts inside.
• Disconnect the product from the power source before cleaning.
• Disconnect the product from the power source before service and when replacing parts.
• Do not use the product if a part is damaged or defective. Replace a damaged or defective product immediately.
• Do not let children play with the packaging material. Always keep the packaging material out of the reach of children.
• Always keep the power cable and the product away from usual walkways.
• Do not drop the product and avoid bumping.
• Do not use aggressive chemical cleaning agents when cleaning the product.
• This product may only be serviced by a qualified technician for maintenance to reduce the risk of electric shock.

Connecting the power inverter

• Plug the 12 Volt plug A5 into a 12 Volt power socket.

Powering a socket device

• Make sure the target device is switched off before connecting it.

1. Plug the power plug from a target device into the power socket A1.
2. Set the power switch A3 to ON.

Do not load the power inverter more than 80% during long use (>1 hour).

Powering a USB device

1. Plug a USB cable into the USB port A2 of the power inverter.
2. Plug the other end of the USB cable into your target device.
3. Set the power switch A3 to ON.

Troubleshooting

socket.
| The target device has drawn too much power. The fuse has blown.| 1.   Remove the target device from the power socket.

2.   Remove the 12 Volt plug from the 12 Volt power socket.

3.   Replace the fuse.

-Do not attempt to

| power the same
| target device again.

If the target device is not receiving power, look at the indicator LEDs and listen for alarms. The table below shows what the combinations of lights and sounds mean.

Disposal

The product is designated for separate collection at an appropriate collection point. Do not dispose of the product with household waste. For more information, contact the retailer or the local authority responsible for the waste management.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>