BAINTECH BTBLANKET180 180W Baintuff Solar Blanket User Manual
- June 3, 2024
- BAINTECH
Table of Contents
BAINTECH BTBLANKET180 180W Baintuff Solar Blanket User Manual
Introduction
Go off-grid with the Baintech 180w Solar Blanket. Designed to charge your 4WD,
RV and Marine batteries, this lightweight and compact blanket will produce up
to 10A in optimal conditions. Made with high yielding superior Monocrystalline
Sun power solar cells, the Baintuff 180w Blanket is designed to perform even
in cloudy conditions.
Designed with ease of use in mind, the simple plug and play Anderson plug
connection is secure, safe and easy to connect.
- High efficiency Monocrystalline cells
- Compact
- Light weight
- Plug + Play : NEW plug and play Anderson connection
- All accessories and Solar Controller included
Technical Specification
| Model | 180W – BTBLANKET180 |
|---|---|
| Output | Maximum voltage out – 18 volts Maximum current out – 10 amps |
| Rated Power | 18V 180W |
| Folded Size | 398 x 300 x 78mm |
| Unfolded Size | 1830mm h x 775mm w |
| Weight | 5.11kg |
| Solar Cell | Monocrystalline sunpower solar cell 23.5% efficiency |
| Solar Panel | Matted PET laminated solar panel 8V16WX12pcs |
Included accessories:
-
Solar regulator.
-
6m Power Lead.
-
Red Anderson Connection.
-
Alligator Clamp Connector.
How to connect the blanket to your devices.
Now with a new Anderson connector – the 180w Baintuff solar blanket offers a simple plug and play solution. The blanket comes with an Anderson cable and a Solar Controller. The Solar Controller is normally used when there is no internal controller in your equipment. (ie: when you want to charge your car battery, or a secondary battery in a trailer.)
DC18V OUTPUT
Connect the Anderson connector with solar charger controller and then connect
the Alligator clamps to your batteries. Always connect the battery you are
wanting to charge FIRST to the Solar Controller before connecting the Solar
Blanket. The reason is the Controller’s AUTO SENSING needs to know what
voltage it has to be set at, before the Controller can operate.
USING WITH THE BAINTECH POWERTOP
The grey Anderson connector on the Solar Controller is plugged into the
Powertop’s grey Anderson socket or the battery you are intending to charge.
The red Anderson socket is plugged into the cable from the blanket with the
same. Plugging the grey connector in first, allows the auto-select function to
kick in and determined if the battery is 12 or 24 volts before the blanket is
connected.
SOLAR REGULATOR INCLUDED – See product specifications
Warning and Safety Instructions
Do not drive over the blanket, leave in wet environments – such as rain or sea water, or unattended where wind and theft may occur. If wind is likely to be an issue, use the supplied holes around the edge to tie down or peg the blanket to a secure spot
-
Risk of explosive gases: working in the vicinity of a lead-acid battery is dangerous.
Batteries generate explosive gases during normal operation. For this reason, it is of utmost importance that you follow the instructions each time you use the solar panel charger. -
Solar panel charger should not be used by persons with reduced physical, sensory or mental capabilities unless they are supervised by a person responsible for their safety.
-
Do not charge non-rechargeable batteries by the solar panel charger. It can damage the regulator or solar panel charger or create harm for the operator. Only use the solar panel charger DC18V for charging standard lead-acid, lithium-polymer, Li-Fe, Gel and AGM type 12V batteries .
-
Never smoke or allow a spark or flame in vicinity of battery or engine. This may cause the battery to explode.
-
Please keep the junction box out of water, if there is some water in the junction box, please make sure it’s dry before using. Always clean the blanket after use to keep cells efficient and at their maximum.
ADD ON SOLAR ACCESSORIE
BTWATT01
Take the guesswork out of how much power your solar panels are generating. The Baintech Watt meter once connected will give you real time information on:
- Current (Amps/A)
- Voltage (Volts/V)
- Power (Watts/W)
BTPTOP135V3
Ready to go right off the shelf, this fully portable plug-and-play system
features a 12V 135Ah AGM battery with charging inputs for AC, DC and solar.
Customer Support
Visit www.baintech.com.au to find out more
PRODUCT CODE:
BTBLANKET180 12 Month warranty
Phone: 1300 224 683
email: [email protected]
www.baintech.com.au
