VOLLRATH 3873660N One Piece Cafeteria Breath Guard Installation Guide

: June 1, 2024
: VOLLRATH

Table of Contents

VOLLRATH 3873660N One Piece Cafeteria Breath Guard
Product Information
Product Usage Instructions
Installation Instructions
- One Piece Breath Guard installation
- Three Piece Breath Guard installation
Contact Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VOLLRATH 3873660N One Piece Cafeteria Breath Guard

Product Information

Product Name: Cafeteria Breath Guard
Model: One Piece and Three Piece options available
Manufacturer: Vollrath Company, L.L.C.

Product Usage Instructions

One Piece Breath Guard Installation:
Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figure 1. Repeat for all four uprights.

Three-Piece Breath Guard Installation:

Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2. Repeat for all four uprights.
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
Install the one-piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
Install the side breath protector (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.

FAQ:

Q: What should I do if I accidentally over-tighten the cap nuts during installation?
A: If you accidentally over-tighten the cap nuts, stop immediately to prevent cracking of the plastic. Loosen the nuts slightly and then retighten to the appropriate level to secure the components without causing damage.
Q: Can I adjust the position of the breath guard after installation?
A: Yes, you can adjust the position of the breath guard by loosening the cap nuts slightly to allow for movement, repositioning the guard as needed, and then tightening the nuts securely.

Installation Instructions

These instructions cover the installation of the one-piece Cafeteria Breath Guard and the three-piece Cafeteria Breath Guard.

One Piece Breath Guard installation

Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:

NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.

Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights. $VOLLRATH-3873660N-One-Piece-Cafeteria-Breath-Guard-Fig- $1$$
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
Install the one-piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
Install the side breath protector (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.

Three Piece Breath Guard installation

Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:

NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.

Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights. $VOLLRATH-3873660N-One-Piece-Cafeteria-Breath-Guard-Fig- $2$$
Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
Install the side shield (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.