VOLLRATH 3893746 Cafeteria Breath Guard Installation Guide
- June 1, 2024
- VOLLRATH
Table of Contents
VOLLRATH 3893746 Cafeteria Breath Guard
Product Information
Specifications:
- Product Name: Cafeteria Breath Guard
- Model Numbers: One Piece – 2350030-01, Three Piece – 2350030-02
- Manufacturer: Vollrath Company, L.L.C.
- Material: Plastic
- Color: Clear
Product Usage Instructions
One Piece Breath Guard Installation:
Some units are shipped without the breath guard installed. Follow these steps
to install the one piece Cafeteria Breath Guard:
- Install the breath guard uprights (A) to the studs (B) and secure with cap nuts (C). Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) and secure with cap nuts (C).
- Securely install the one piece breath guard (E) using screws (F) and cap nuts (C) at all four mounting locations.
- Attach the side breath protector (G) to the support tube (D) and secure with cap nuts (C) on both sides.
Three Piece Breath Guard Installation:
For the three piece Cafeteria Breath Guard installation, follow these steps:
- Install the breath guard uprights (A) to the studs (B) and secure with cap nuts (C). Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) and secure with cap nuts (C).
- Securely install the side breath guards (E) using screws (F) and cap nuts (C) at all mounting locations.
- Attach the side shield (G) to the support tube (D) and secure with cap nuts (C) on both sides.
- Attach the support bar and stud assembly (H) to the side breath guards (E) at all mounting locations.
- Finally, install the top breath guard (I) to the support bar and stud assembly (H) and secure with cap nuts (C) at all mounting locations.
Frequently Asked Questions (FAQ):
-
Q: What should I do if I encounter cracked plastic during installation?
A: If you encounter cracked plastic during installation, stop immediately to prevent further damage. Contact our service department at 800.628.0832 for assistance. -
Q: Can I disassemble the breath guard after installation for cleaning?
A: Yes, you can disassemble the breath guard for cleaning purposes. Follow the installation steps in reverse order to disassemble, clean, and then reassemble the breath guard.
These instructions cover the installation of the one pice Cafeteria Breath
Guard and
the three piece Cafeteria Breath Guard.
Breath Guard Installation
One Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:
NOTE: Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
Three Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE: Use caution when tightening the cap nuts. Overtightening may cause
the plastic to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
The Vollrath Company, L.L.C.
1236 North 18th Street
Sheboygan, WI
53081-3201
U.S.A.
Main Tel: 800.628.0830
Service Tel: 800.628.0832
FAX: 800.752.5620
Vollrath of Canada, Co.
Tel: 800.695.8560
FAX: 800.752.5620
© 2010 The Vollrath Company, L.L.C.