suncast BMC3601 Single Drawer Base Cabinet Instruction Manual
- June 5, 2024
- suncast
Table of Contents
suncast BMC3601 Single Drawer Base Cabinet Instruction Manual
Tools Needed for Installation
KEEP THESE INSTRUCTIONS. You will need the Quality Control Number shown
below to register your product
Quality Control Number:
Before You Begin
- Read instructions thoroughly prior to assembly.
- This kit contains parts that can be damaged if assembled incorrectly or in the wrong sequence.
- Please follow instructions
- Suncast is not responsible for replacing parts lost or damaged due to incorrect assembly.
- Check for all parts before you begin assembly.
- Using the provided parts check list, verify that you have all the parts required to construct your cabinets.
- Assistance is required during parts of the assembly
Caution
- THIS PRODUCT IS RECOMMENDED FOR INDOOR USAGE.
- Not intended for storage of flammable or caustic chemicals.
- Not intended for usage by children.
- To avoid risk of suffocation, do not allow children to play inside container.
- This product may become susceptible to impact damage in freezing temperatures.
- Do not store near excessive heat.
- Exercise caution when moving fully loaded product. This product is not intended for transporting heavy objects. Use as a stationary storage device only.
- Do not sit or stand on top.
- Do not store items on top.
- Max load 30 lbs. per drawer.
- Mounting to wall studs is recommended.
- Mount flush and level to wall.
- Do not stack units.
WARNING
Children have died from furniture tip over. To reduce the risk of furniture tip over:
-
ALWAYS install tip over restraint provided.
-
NEVER put a TV on this product.
-
NEVER allow children to stand, climb, or hang on drawers, doors, or shelves.
-
NEVER open more than one drawer at a time.
-
Place heaviest items in the lowest drawers.
This is a permanent label. Do not remove!
Care Instructions
To maintain the look of your product, we recommend cleaning it each year with mild soap and water. DO NOT use bleach, ammonia, or other caustic cleaners, and DO NOT use stiff bristle brushes. Failure to perform annual cleaning could result in permanent staining of the plastic. This is not a manufacturing defect and is not covered under warranty. This product is not recommended for outdoor usage.
Suncast Products and Replacement Parts
To purchase Suncast replacement parts and learn about other Suncast products visit us online or call.
www.suncast.com
24 hours a day, 7 days a week, 365 days a year.
1-800-846-2345 or 1-630-879-2050
Parts
Hardware
Hardware shown at actual size (*Unless otherwise noted). Extra hardware
provided.
Not all are used.
Pre-assembly
Before you begin, separate the drawer glides into two parts, the wide base and
the narrow glide. Repeat for all six glides.
Use 4mm Hex Key (N) to thread three insert nuts (S) into left side panel (C). Repeat for right side panel (B).
Lay drawer box panel (K) flat with grooved side facing up. Thread six
insert nuts (S) into the drawer box sides.
Attach one drawer glide base (X) to the left side panel with three screws (T).
Repeat on right side panel (B).
Note: The rubber bumper-stops go toward the back of the cabinet. To
access screw locations, line them up with the slot in the moving part.
Lower the back of the drawer box to the floor. Fold the left side up, followed
by the right side. Press the back of the drawer against the floor, folding it
over the corner tabs. The tabs must be securely snapped through the back
corner slots.
Slide the drawer front (J) down over the tabs on the front edge of the drawer
box (K). Press down until the panel snaps in place.
Turn the drawer box over and secure the drawer front with three screws (AA). Note: the screw locations are not pre-drilled.
Starting with the front screws, attach the narrow portions of the drawer
glides (X) to each side of the drawer using 6 screws (T).
NOTE: The plastic catch is always toward the back.
Insert drawer handle (M) into drawer front (J) by catching the top edge on the
opening and rotating the botton edge until it snaps into position.
Assembly
Make sure all tabs are engaged before locking panels together
Align tabs on left side panel (C) with slots on bottom panel (A). Lower
side panel into slots and lock in place by sliding panel towards front. Repeat
with right side panel (B).
Align and engage tabs on back panel (D) with slots on side panels (C/B). Push panel (D) down to lock in place.
Attach support bracket (P) to top panel (E) using four screws (AA).
Align slots on top panel (E) with tabs on side panel (C/B). Lower
top panel and lock in place by sliding panel towards front. Top will overhang
front slightly.
Base Cabinets must be securely attached to a wall in order to prevent tipping
Using a 1/2˝ drill bit, drill through the two provided locations on Back Panel (D). Place cabinet in desired location. With a pencil mark the hole locations on the wall, and drill through the wall with 1/2˝ drill bit.
Add Washer (M) to Toggle Bolt (N). Close toggle bolt before putting through
1/2˝ hole or it will not fit. Wings on toggle bolt need to be positioned
toward the end of the bolt. While holding cabinet in place, put toggle bolt
through drilled holes in cabinet and wall. Tighten screws to secure to wall.
Attach support bracket (P) to middle shelf (F) using four screws (AA).
Attach support bracket (P) to bottom shelf (L) using four screws (AA).
Insert shelf (L) with the hinge holes facing up into cabinet at an angle. Low.
Tab on shelf must engage with slot on inside panels. Push side panels inward to engage.
Tilt shelf (L) forward and place front corners of shelf into indented area on
side panels. Push down on back of shelf to snap into position.
Insert shelf (F) into cabinet at an angle. Lower shelf down onto support ribs.
Tab on shelf must engage with slot on inside panels. Push side panels inward to engage.
Tilt shelf (F) forward and place front corners of shelf into indented area on side panels. Push down on back of shelf to snap into position.
Insert drawer handle (M) into right door (G) by catching the inside edge on
the opening and rotating the outside edge until it snaps into position.
Repeat for left loor, (H).
Install right door (G) by inserting bottom hinge pin into shelf (L) and
sliding top hinge pin into position in top panel (E). Repeat for left door
(H).
Install bottom drawer by fitting the drawer mounted glides into the side panel
mounted glides.
Completed Assembly
Warranty
SUNCAST® Storage Cabinet Five Year Limited Warranty
Your SUNCAST® Storage Cabinet has a FIVE YEAR LIMITED WARRANTY against product
failure resulting from defects in manufacturing or materials.
The warranty period starts on the delivery date. Incidental and consequential
damages are not covered.
Warranty Claims
To file a warranty claim contact the manufacturer, SUNCAST® CORPORATION, 701 North Kirk Road, Batavia, Illinois, 60510. Call toll free 800-846-2345 or visit www.Suncast.com.
SUNCAST® will repair or replace only the parts that failed under the terms of the warranty. In some cases, the replacement parts may not be identical, but they shall be of equal or greater performance than the original part.
We may require proof of purchase. Proof of purchase may be the original dated store receipt. We may require evidence of the failure. Evidence of failure may include photographs or returning failed components to SUNCAST.®
WARRANTY LIMITATIONS
THIS WARRANTY COVERS ONLY DEFECTS THAT AFFECT THE FORM, FIT OR FUNCTION OF THE
UNIT. It excludes natural aging of the unit, discoloration, ordinary wear and
tear, ordinary weathering, sunlight fading, or rust. It excludes staining
caused by mold, mildew or tree sap and damage caused by animals including
insects, vermin or household pets. The warranty does not cover damage caused
by Acts of Nature including but not limited to: wind in excess of 65 mph;
tornado; hurricane; microburst; hail; flood; blizzard; extreme heat; pollution
or fire events. The warranty does not cover damage caused by Sun energy
reflected from “Low-E” windows or other reflective materials. The user is
responsible for protecting the product from damage in this situation.
The following actions void the warranty: improper assembly; assembly on a
foundation other than as described in the assembly instructions; use above
intended and reasonable capacity; misuse; abuse; failure to perform ordinary
maintenance; modification; cleaning with abrasive tools, exposing the unit to
heat sources and vandalism. Painting, sandblasting, cleaning with harsh
chemicals not recommended for plastics voids the warranty on resin components.
Modification of the original product voids all warranties. Suncast assumes no
liability for any modified product or consequences resulting from failure of a
modified product. Damage due to moving, transporting,or relocating the product
voids the warranty.
Disassembly of this unit for reasons other than authorized repair voids the
warranty.
THIS WARRANTY IS NONTRANSFERABLE. IT IS VALID FOR NORMAL HOUSEHOLD USE ONLY. THE WARRANTY IS VOIDED BY COMMERCIAL OR INDUSTRIAL USE. IT EXCLUDES FLOOR MODELS, CLEARANCE AND OPEN BOX UNITS.
Notice
Suncast® does not represent that this unit will meet city, county, state, homeowner’s association standards or zoning requirements. The owner is responsible for securing all permits and meeting other requirements needed for placement, construction and use.
THE MANUFACTURER’S LIABILITY HEREUNDER IS LIMITED SOLELY TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT OR PART AND THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES WHICH MAY RESULT FROM ANY DEFECT IN MATERIAL OR WORKMANSHIP OR FROM THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages; the limitation or exclusion may not apply to you.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>