VOLLRATH 3873760 Cafeteria Breath Guard Installation Guide
- June 1, 2024
- VOLLRATH
Table of Contents
VOLLRATH 3873760 Cafeteria Breath Guard
Product Information
Specifications:
- Product Name : Cafeteria Breath Guard
- Types: One Piece and Three Piece
- Manufacturer: Vollrath Company, L.L.C.
- Item No.: 2350030-01
- Revision Date : 04/12
Product Usage Instructions
One Piece Breath Guard Installation:
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figure 1. Repeat for all four uprights.
Three Piece Breath Guard Installation:
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
FAQ
- Q: What should I do if I over-tighten the cap nuts?
- A: Overtightening may cause the plastic to crack. If you have over-tightened the cap nuts, stop immediately and assess the damage. Contact customer service for replacement parts if needed.
- Q: Can I install the breath guard without using all the provided hardware?
- A: It is recommended to use all provided hardware during installation to ensure proper assembly and stability of the breath guard.
These instructions cover the installation of the one pice Cafeteria Breath Guard and the three-piece Cafeteria Breath Guard.
Installation
One Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
three Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
The Vollrath Company, L.L.C. 1236 North 18th Street Sheboygan, WI 53081-3201 U.S.A.
- Main Tel: 800.628.0830
- Service Tel : 800.628.0832
- FAX: 800.752.5620
- Vollrath of Canada, Co.
- Tel: 800.695.8560
- FAX: 800.752.5620
© 2010 The Vollrath Company, L.L.C.