BEGA 51 246.1 Wall Luminaire For Indoor Use Instruction Manual
- June 1, 2024
- BEGA
Table of Contents
IP 44
51 246.1
15.23
Technical amendments reserved
Wall luminaire for indoor use
51 246.1 Wall Luminaire For Indoor Use
Instructions for use
Application
Wall luminaire · Indoor luminaire with white translucent cover made of
synthetic material and aluminium housing, for special lighting applications
indoors.
A luminaire with unshielded and uniform light distribution that can be
installed either vertically or horizontally.
Luminaire with high protection class.
Product description
Luminaire housing made of aluminium
Finish colour velvet white
Synthetic cover, translucent white
Silicone gasket
4 mounting holes ø 4.8 mm
Distance 900 x 81 mm
2 cable entries for through-wiring for mains cable up to ø 10,5 mm max. 5 x
1.5@
Connection terminal 2.5@
Earth conductor connection
Complies with flicker requirements in accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit 220-240 V 0/50-60 Hz DC 176-276 V
During DC operation the LED power is reduced to 15 %
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables
BEGA Thermal Control® Temporary thermal regulation to protect temperature-
sensitive components without switching off the luminaire
Safety class I
Protection class IP 44
Protected against granular foreign bodies
≥ 1 mm and splash water
– Conformity mark
Weight: 3.0 kg
This product contains light sources of energy efficiency class(es) D
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we
recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
Safety
The installation and operation of this luminaire are subject to national
safety regulations.
Installation and commissioning may only be carried out by a qualified
electrician.
The manufacturer accepts no liability for damage caused by improper use or
installation.
If subsequent modifications are made to the luminaire, the person responsible
for these modifications shall be considered the manufacturer.
Lamp
| Module connected wattage | 39 W |
|---|---|
| Luminaire connected wattage | 44 W |
| Rated temperature | ta= 25 °C |
| Ambient temperature | ta max = 35 °C |
51 246.1 K3
Module designation
2x LED-1306/930 + 4x LED-1307/930
Colour temperature ……………3000 K
Colour rendering index…………. CRI > 90
Module luminous flux ……………….5900 lm
Luminaire luminous flux …………….. 4172 lm
Luminaire luminous efficiency ……………….. 94,8 lm / W
Prior to installation, please note:
To ensure correct mounting and installation of the luminaire, the luminaire
base must be installed on an even surface.
IMPORTANT: For installation and dismantling of the luminaire top, a
clearance of 60 mm is required on each side in the area of the two lateral
luminaire caps (hexagon socket screw, wrench size 1.5).
Installation
LED are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during
installation or relamping.
Remove the luminaire base from its packaging.
Pass the power connecting cable through the cable entry into the luminaire
base.
Drill mounting holes into the mounting surface – spacing 900 x 81 mm
Attach the luminaire base on the installation surface using the material
supplied or other suitable mounting material.
Shorten the power connecting cable to max.
150 mm and strip the coating to 100-120 mm.
Carefully remove the luminaire top from its packaging and guide the back side
against the luminaire base.
Establish earth conductor connection and make the electrical connection to the
terminals.
For digital control please use the connecting terminal DA, DA.
In case this terminal is not used the luminaire will be operated at full light
output.
NOTE: To make it easier to secure the luminaire top on the luminaire
base, it is helpful to pre-shape the rigid connecting wires – see diagram.
IMPORTANT: To guarantee the luminaire’s safety class, make sure that the
pre-shaped connecting wires are within the rectangular sealing area and not
protruding out of it.
Guide the mounting sockets of the luminaire top exactly onto the installation
bolts of the luminaire base – in the process, check the sealing area of the
connecting wires.
Applying even pressure on both sides, lock together the luminaire top and
luminaire base. Screw in the two hexagon socket locking screws (wrench size
1.5) approximately 1.5 mm deeper than the cover surface. This ensures a secure
connection between the luminaire top and luminaire base. Dismantle the
luminaire in reverse order. Loosen the hexagon socket locking screws.
Insert a screw driver into the flat opening at the edge of the two front
covers and lift the luminaire top on both sides away from the luminaire base
against the resistance of the locking mechanism.
Replacing the LED module
The designation of the LED module is noted on a separate label in the
luminaire or on the underside of the specific LED module.
It is also listed in the spare parts overview at the end of these instructions
for use.
The light colour and light output of BEGA replacement modules correspond to
those of the modules originally fitted. The module can be replaced by a
qualified person using commercially available tools.
Disconnect the system from the power supply.
Unscrew both side hexagon socket locking screws (SW 1.5) by
about 3 mm from the covers of the wall luminaire.
Insert a screw driver into the flat opening at the edge of the two front
covers and lift the luminaire top on both sides away from the luminaire base
against the resistance of the locking mechanism.
Remove the wires on the power connecting cable from the terminals marked (L),
(N), DA DA.
Position the luminaire top on a soft surface (e.g. on both thighs).
Please note:
The side cover of the luminaire in the area of the connection terminal is
braced by a spring mechanism.
The screw of the spring mechanism is accessible via the rectangular opening on
the back of the luminaire top.
IMPORTANT: The following work step requires the force of both hands in
order to evenly exert pressure on the screw and counterpressure on the spring
mechanism!
While you loosen these screws, press down with your hand from the top on the
Torx screwdriver (TX 20) and generate lateral counterpressure ( ! ) on the
screwdriver at the same time using several fingers of the other hand in order
to slowly relieve the spring force.
Pull the side cover off the synthetic cover in the area of the
rectangular recess and unhook it.
Pull the synthetic cover off the remaining cover and carefully guide it away
over the electrical LED unit.
Remove the LED module. Install the replacement LED module.
Follow the installation instructions for the LED module.
In case of a defect, the PSU can be replaced in this work step.
Carefully guide the synthetic cover over the LED unit.
Make sure not to damage the LED module.
A defective luminaire cover must be replaced.
The LED support profile is equipped with a locking device.
This locking device must be inserted with its insertion opening first over the
latching sleeve of the luminaire top (in the area of the rectangular opening).
Press the side cover of the LED support profile into the synthetic cover of
the luminaire top.
Make sure the gasket is correctly seated.
NOTE: In order to install the second side cover safely, it is recommended
to place the luminaire top on a soft surface (e.g. on both thighs).
To apply counterpressure on the first side cover (of the LED support profile),
a 2nd person is helpful.
Push the screw of the spring mechanism as far as it will go in the direction
of the cover to be braced.
Pick up the side cover and guide it with the inner hole over the suspension
pin of the spring mechanism.
Insert the cover and press it sideways against the synthetic cover of the
luminaire top as far as it will go.
Make sure the gasket is correctly seated. As before, the following work step
again requires the force of both hands in order to evenly exert pressure on
the screw andcounterpressure on the spring mechanism!
Guide the Torx screwdriver (TX 20) onto the screw of the spring
mechanism.
Press down with your hand from the top on the Torx screwdriver and generate
lateral counterpressure ( ! ) on the screwdriver at the same time using
several fingers of the other hand.
Tension the spring against the tensile force until the stop is reached.
Tighten the screw in the end position.
Make the electrical connection and reinstall the wall luminaire in reverse
order as described under “Installation”.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt.
Spares
| Synthetic cover | 15 000 682 B3 |
|---|---|
| Cover with gasket | 20 000 121 B1 |
| LED power supply unit | DEV-0469/1400i |
| LED module 3000 K | LED-1306/930 |
| LED module 3000 K | LED-1307/930 |
BEGA Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
info@bega.com
www.bega.com
Documents / Resources
| BEGA
51 246.1 Wall Luminaire For Indoor
Use
[pdf] Instruction Manual
51 246.1 Wall Luminaire For Indoor Use, 51 246.1, Wall Luminaire For Indoor
Use, Luminaire For Indoor Use, Indoor Use
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>