GOTRAX F1V2 Electric Bike User Manual

June 1, 2024
GoTrax

F1V2 Electric Bike

“`html

Specifications:

  • Model: F1V2
  • Dimensions: 1380 x 250 x 600mm (54.3 x 9.8 x 23.6in)
  • Maximum Distance: 40 miles (65km)
  • Maximum Speed: 22 miles (35km)
  • Tire Pressure: 35 PSI

Product Usage Instructions:

Front Wheel Installation:

  1. Loosen the front axle screws to a suitable position for
    installation.

  2. Slowly install the front wheel onto the front fork with the
    brake pads aligned. Ensure the spacer hook is hung into the front
    fork.

  3. Use a 15mm open-end wrench to tighten the fixing screws on both
    sides of the front wheel.

Installation of Headlights and Taillights:

  1. Attach the front headlight bracket to the mounting hole, insert
    a screw, and fasten with a nut. Tighten using a 5mm hex key and a
    10mm open-end wrench.

  2. Align the tail light bracket with the frame holes and tighten
    the securing screws using a 5mm hex key.

Accessory Installation:

  1. Install the seat bag by aligning the guide groove with the
    lower seat and hanger, then tighten.

  2. Insert the rearview mirror into the handlebar end hole, adjust
    to desired height, and lock with a 6mm L wrench.

  3. Place the phone holder on the bike handlebar and secure with a
    cross screwdriver.

FAQ:

Q: What should I do if the battery display shows critically low

battery?

A: When the battery display border is flashing, it indicates
critically low battery. Immediate charging is required to avoid
disruption during usage.

Q: How many gear positions are available for power assist gear

selection?

A: There are a total of 0-5 gear positions available. The
default position on startup is 0, which is neutral with no power
output. Use the +/- buttons to adjust gear positions.

“`

F1V2

Contents
Don’t Ride Until You Read This …………………………………………… 02 Warning Message ……………………………………………………………… 03 Unpacking and Product Specs ……………………………………………. 07 Get to Know Your E-Bike ……………………………………………………. 08 Front Wheel Installation Procedure ……………………………………. 09 Installation of headlights and taillights ………………………………. 10 Handle Bar Installation and Folding …………………………………… 11 Bike Frame Folding and Unfolding …………………………………….. 13 Pedal Installation and Folding ……………………………………………. 14 Saddle Installation and Adjustment …………………………………… 15 Accessory Installation Procedure ………………………………………. 16 Removing the Battery ………………………………………………………… 17 Turn on the battery output ………………………………………………… 17 Charge Your E-Bike ……………………………………………………………. 18 Charge Your E-Bike: Method 2 …………………………………………… 19 Tire Inflation Instructions ………………………………………………….. 20 Maintenance & Repair………………………………………………………… 22 Function Definition ……………………………………………………………. 25 Function Mode ………………………………………………………………….. 31 Battery Information …………………………………………………………… 32 Troubleshooting Guidance ………………………………………………… 34 Warranty …………………………………………………………………………… 35

bicycle
TOOLS INCLUDED:3mma4mma5mma 6mm Allen wrech, 8mm&10mma 13mm&15mm open-end wrench,Flat Head & Phillips dual-purpose Screwdrive.
01

WARNING: Lithium-ion Batteries and/or products that contain Lithium-ion Batteries can expose you to chemicals including cobalt lithium nickel oxide, and nickel, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
02

03

04

05

06

3

4

TOOLS: (2)LARGE WRENCH, (4)ALLEN WRENCHES, (1)SCREWDRIVER

Seat Bag

5

6

7

8

Rearview Mirror

Folding Lock

Phone Holder

F1V2 1380250600mm(54.39.823.6in)

Pedals

40miles (65km) 22miles (35km) 35 PSI
07

Phone Holder Rearview Mirror
Seat Bag
08

Front Wheel Installation Procedure

1.Remove packing block from disc brake caliper ­ Do Not Throw Away ­ Re- install Packing Block whenever you remove your front wheel.

2.Loosen the front axle screws (it doesn’t need to be totally loose, just to a suitable position for installation).

3.Slowly install the front wheel on the front fork andthe brake pads in the brake. Note: The spacer is asshown in the picture, the spacer hook needs to behung into the front fork, and the positions of thespacers on both sides are the same.

4.Use a 15mm open-end wrench to tighten the fixingscrews of the front wheels on both sides.
09

Installation of headlights and taillights
Attach the front headlight bracket to the front headlight mounting hole, align it with the corresponding installation hole on the bracket, insert a screw, and on the other end, fasten it with a nut. Tighten the front headlight securing screw with a 5mm hex key on one end and a 10mm open-end wrench on the other end. (the screws have been installed on theframe, remove the screws and install).
Align the tail light bracket with the corresponding mounting holes on the frame, and use a 5mm hex key to tighten the two securing screws.(the screws have been installed on theframe, remove the screws and install).
10

11

12

13

14

15

Accessory Installation Procedure
Installation instructions for the rearview mirror, seat bag, and phone holder please follow the below notes

1.Install the seat bag: align the guide groove on the seat bag at the lower seat and hanger, advance and tighten.

2.Install the rearview mirror, insert the rearview mirror into the handlebar end hole, adjust to the properor comfortable height, and lock with a 6mm “L “wrench.
16

3.Install the phone holder: put the phone holder on the bike handlebar, and use a cross screwdriver to lock the screw.

17

18

19

20

21

22

23

24

Battery level display Fault Indication Real-time Speed
Power Assist Push Icon Single Trip Mileage Total Travel Distance Maximum Speed Average Speed
Minus Button Power On/Off Button

Headlight Icon Speed Unit Display
Gear Display Range and Unit Display
Plus Button Confirm “i” Button Headlight Button
25

Power On/Off: Press and hold the button for 2-3 seconds to activate the display and press the button again for 2-3 seconds to turn off the display (the bike will automatically power off , if there is no activity for 10 minutes in a stationary state). Display Data Switching: After the display panel is powered on, it defaults to displaying real-time, speed and total mileages. Press the button shortly to switch between total mileage, single trip mileage, max speed, and average speed in the displayed information. Power Assist Pushing: Long press the button, and the electric bike enters the power assist pushing mode. The electric bike will travel at a constant speed of 6 kilometers per hour. At the same time, the screen will display the power assist icon. Release the button to exit the power assist mode, and the power assist icon will go off. Turning On/Off Headlights: Shortly press the button to turn on the headlights, and the display panel backlight will dim. Press the button again to turn off the headlights, and the display panel backlight will return to its normal brightness.
Power Assist Gear Selection: There are a total of 0-5 gear positions, and the default on startup is 0, which is a neutral position with no power output. Shortly press the or button to increase or decrease the gear position. (In power assist mode 1-5, there are gear distinctions, while in electric mode 1-5, there are no gear distinctions).
26

Battery Display: In a fully charged state, the battery display shows 5 levels of charge. As the battery level decreases, the bars are reduced accordingly. When the border is flashing, it indicates critically low battery and requires immediate charging.
Fault Codes: When there is a malfunction in the electric bike’s electronic control system, the display screen will automatically show “ERROR” along with an error code. Only when the fault is resolved can you exit the fault display screen. After a fault occurs, the electric bike will not be able to continue to operate. Please contact the GOTRAX after-sales team for assistance or seek the help of a professional technician to diagnose and rectify the issue. Setting Mode: 1.Simultaneously hold the or button for more than 2 seconds to enter the personalized parameter selection interface. 2.Shortly press the or button to switch between personalized parameter settings. Press the button to enter the parameter change mode. 3.Shortly press the or button to select parameters. A long press of for continuous increase and long press of for continuous decrease. 4.Press the button shortly to save the parameter settings and return to the personalized parameter selection interface. 5.Long press the button to save the parameter settings and exit the personalized parameter selection interface.
27

Metric/Imperial Unit Setting: “01P” is the option for selecting metric or imperial units. “00” represents metric and “01” represents imperial Use the or button to make the selection, and press the button shortly to save the parameter setting and return to the personalized parameter selection interface. Voltage Setting: “02P” is the option for setting the rated voltage, and you can set the rated voltage to 24V, 36V, or 48V. The factory default is 48V. Adjusting the voltage may lead to incorrect battery level display, so it’s advisable not to adjust it unless necessary. Gear Range Setting: “03P” is the option for setting the range of power assist gears. The instrument panel offers the choice of power assist gear ranges, including 0-3, 1-3, 0-5, and 1-5. The factory default is 0-5. (0-3/0-5 indicates there is a 0 gear, with 0 gear being a neutral state or park gear, while 1-3/1-5 indicates there is no 0 gear, meaning there is no neutral or park gear). Wheel Diameter Setting: “04P” is the option for setting the wheel diameter, and the available wheel diameter options on the display screen are 16, 18, 20, 22, 24, 26, 700C, and 28 inches. The factory default is 22. Adjusting the wheel diameter can lead to inaccurate speed and mileage display. Therefore, this setting is locked and not adjustable.
28

Speed Limit Setting: “05p” is the option for setting the speed limit in power assist mode, and the adjustable range for the vehicle speed limit is 10 to 40 km/h. The factory default is 32 km/h, and the maximum limit is 40 km/h. This mode allows you to adjust the speed limit only for power assist mode, as the electric mode has a maximum limit of 32 km/h, which is not adjustable.
Power-On Password Setting: “06P” is the option for setting the power-on password. The power-on password function is disabled by default, and users can enable it by setting a password.The default password when the display is shipped is “1212,” but you can change it to another four-digit number. To enable the power-on password: In the “06P” interface, press the button shortly to enter the parameter change mode. Use the or button to select “PSd-y” to enable the power-on password. Then, long press the button to save and exit. The password function is now enabled successfully. To disable the password: In the “06P” interface, press the button shortly to enter the parameter change mode.Use the or button to select “PSd-n” to disable the power-on password. Press the button to confirm and exit to the personalized settings selection interface. Then, either long press the button to return to the main interface or directly long-press the button to exit to the main interface. The password function is now successfully disabled.
29

To change the password: In the “06P” interface, press the button shortly to enter the parameter change mode.Use the or button to select “PSd-y” to enable password change.Press the button to confirm and enter the four-digit password setting mode.In the password setting interface, input your new password. Use the or button to select the digits and press the button to save each digit and move to the next. Set all four digits this way.When the lat digit is flashing, long press the button to save the new password and exit the parameter setting interface. The password is now changed, and it will take effect upon reboot. Please remember the new password you set, as you will need it each time you power on and change the password.
30

31

32

33

ERROR 21 ERROR 22 ERROR 23 ERROR 24 ERROR 25
ERROR 30 34

The motor current failure

Check the motor connection cable. If the connection cable is normal, replace the a new motor.

The throttle abnormal

Check the throttle connection cable. If the connection cable is normal, replace the throttle.

The motor phase line failure
Motor hall signal is abnormal

Please check the motor connection cable at firstly. If the connection cable is normal, replace the motor.
Check the motor connection cable, if the connection cabel is normal, replace the motor.

The brake faulire

Before power on the vehicle please check the brake lever if reset and the connection cable is normal, if they’re not have any issues ,replace the brake levers.

The display communication faulire

Check if the connection cable between the display and the controller is abnormal, and replace the display if there is no abnormality .

35

(US) W W W .G OT R A X . C O M (CA)www.gotraxcanada.com

(US)GOLABS,INC
GOTRAX.com 2201 Luna Rd. Carrollton,TX 75006
(CA)Tao Motor Canada Inc.
170 Bartor Road, Unit 1 North York, Ontario M9M 2W6, Canada.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals