STANLEY TLH-120T HEAVY Tilt TV Mount Installation Guide
- May 15, 2024
- Stanley
Table of Contents
Model : TLH-120T
TV Mount
Installation Guide
TLH-120T HEAVY Tilt TV Mount
Thank you for choosing Stanley – the hardware of choice for Architects,
Contractors, and Home Owners for its quality, performance and dependability.
Enclosed are your step-by-step instructions for an install made easy.
If you get stuck, give customer
service a call at 1-855-816-6868
You can also reach us at
contact@suncraftsolutions.com
Caution: Please read the entire manual before proceeding View warranty and disclaimer on page 11
Getting Started
Before we start lets make sure we have the correct mount and all the required
tools and hardware to complete the installation.
The TV is a Flat Panel TV is between 60” – 120” and weighs no more than 264
lbs.
** The Wall the TV will be mounted on is either concrete or dry wall with
wood studs.
You have all of the following tools:
If you answer “Yes” to all the questions above then
you are ready to begin the TV Mount installation!
Caution:** This product contains small items that could be a choking hazard
if swallowed.
Parts & Hardware
Caution: Before starting assembly, verify all parts are included and
undamaged. If any parts are missing or damaged, do not return the damaged item
to your dealer; contact Customer Service. Never use damaged parts or
previously used parts!
Step 1: Attach Mounting Bracket to TV
-
Check what screw size will fit in your TV (M-A,M-B,M-C M-D,).
Note: you may need to use longer screws with Washer (M-E). -
Align the mounting bracket (B) onto the back of the TV and install with the appropriate hardware and tighten.
Note: If the back of your TV is curved,use the appropriate combination of Spacer (M-F/M-G) to level the mounting brackets.
Tool Required:
Caution: Hand tighten with
screwdriver only, over tightening may damage the TV!
Do not use an electric drill for this step!
Step 2A: Install Wall Plate on Drywall with Wood Stud
Note: For Concrete skip to Step 2B
-
Use the stud finder to locate 3 studs. Then draw a vertical line marking the center of the stud.
-
Level the wall plate and align it with the center of the studs. Make 6 Pencil marks to indicate where to drill.
Tools Required:
Caution: The minimum size of the woodstud must be
2”x 4” and the thickness of the drywall must not exceed 5/8”. -
Remove the wall plate and drill the pilot holes with a 1/4” drill bit.
-
Align the wall plate with the pilot holes and insert 6 bolts through the washer in the pilot holes and tighten.
Note: Make sure the washers (W-C) is placed above the wall plate.
Tools Required:
Step 2B: Install Wall Plate on Concrete
- Level the wall plate and make 6 marks with pencil to show where to drill the pilot holes.
- Remove the wall plate and drill the pilot holes with a 1/2” drill bit.
Tool Required:
Caution: The minimum depth of the concrete
must be 8”. Do not drill pilot holes into the mortar between the concrete.
Insert the anchors into the 6 pilot holes. Tap with a hammer.
Align wall plate with pilot holes and anchors. Insert 6 bolts through washers and anchors then tighten with wrench.
Tools Required:
Step 3: Hang Your TV
- Lift the TV and secure it with the hook on the top bracket, Always have two people lift TV.
- After the TV is hanging properly on the wall mount, press on the bottom edge of the TV towards the wall to lock it in place.
Use the finger to hold on the TV, press in the plate(B)
Warning: Always have two people lift TV.
Listen for click to ensure mount is
locked in place
Step 4: Tilt Angle Adjustment
- Level TV and use Hex key(D) to adjust tension screw for appropriate tension for tilting TV.
SUNCRAFT SOLUTIONS INC. LIMITED WARRANTY
SUNCRAFT SOLUTIONS INC. LIMITED WARRANTY
SUNCRAFT SOLUTIONS, INC. warrants its products to be free of defects in
material and workmanship for the product’s Warranty Period. The Warranty
Period commences on the original purchase date of the product and the sales
receipt serves as proof of purchase.
All SUNCRAFT SOLUTIONS, INC. products are covered by a limited product
warranty of three (3) years for all metal mounts and fixtures and non
electrical items This Limited Warranty extends only to the original purchaser
and is non-transferableIt is automatically void if your SUNCRAFT SOLUTIONS,
INC. product is modified or altered in anyway, improperly or incompletely
installed, usage of non-supplied hardware and used in a non-conventional
method, exceeding the weight capacity or size restrictions. All SUNCRAFT
SOLUTIONS,INC. products are intended for indoors consumer or commercial use
only and any outdoor or use in areas subject to weather and high humidity,
water vapor or exposure to the elements use voids this Limited Warranty. The
Limited Warranty for all mounts is void if the mount is transferred from one
location to another. To the maximum extent permitted by applicable law,
SUNCRAFT SOLUTIONS,INC. disclaims any other warranties, express or implied,
including warranties of fitness for a particular purpose and warranties of
merchantability. SUNCRAFT SOLUTIONS, INC. will not be liable for ny damages
whatsoever arising out of the use or inability to use its products, even if
SUNCRAFT SOLUTIONS,INC. has been advised of the possibility of such damages.
To the maximum extent permitted by applicable law, SUNCRAFT SOLUTIONS, INC.
disclaims any responsibility for incidental or consequential injuries, damages
to persons, properties and other items. For warranty claims made during the
stated warranty period, SUNCRAFT SOLUTIONS, INC. will replace any defective
product part free of charge. Contact SUNCRAFT SOLUTIONS, INC. at
1-855-816-6868 to make a warranty claim
or e-mail
warranty@suncraftsolutions.com. Proof
of warranty is required. This Limited Warranty does not cover the costs of
removing and replacing defective parts from your SUNCRAFT SOLUTIONS, INC.
product. SUNCRAFT SOLUTIONS, INC. assumes no liability for any installation,
adjustment or other costs.
GENERAL DISCLAIMER
General Disclaimer
Disclaimer – Suncraft Solutions Inc. has extended every effort to ensure to
accuracy and completeness of this manual. However, Suncraft Solutions Inc.
does not claim that the information covers all installation, situational or
operational variables. The information contained in this document is subject
to change without notice or obligation of notification of any kind. Regarding
the information contained herein, Suncraft Solutions Inc. makes no
representation of warranty, expressed or implied, and assumes no
responsibility for accuracy, sufficiency, or completeness of the information
contained in this document.
WARNING: FAILURE TO READ, THOROUGHLY UNDERSTAND, AND FOLLOW ALL
INSTRUCTIONS CAN RESULT IN SERIOUS PERSONAL INJURY, DAMAGE TO PERSONAL
PROPERTY, OR VOIDING OF LIMITED WARRANTY!
It is the responsibility of the installer of this product to ensure all
components are properly assembled and installed using the instructions
provided. If you do not understand these instructions or have any questions or
concerns, please contact customer service at
1-855-816-6868 or
service@suncraftsolutions.com. Do not
attempt to install or assemble this product if the product or hardware is
damaged or missing. In the event that replacement parts or hardware are
needed, please contact Customer Service at
1-855-816-6868 or
service@suncraftsolutions.com .
International customers needing assistance should contact the Dealer from
which they purchased the product. The included hardware is designed for use on
vertical walls constructed of wood studs or solid concrete. A wood stud wall
is defined as consisting of a minimum of 2×4 wooden studs (1.5” wide by 3.5”
deep 51 x 102 mm) with a maximum of 5/8” (16 mm) drywall. The included
hardware is not designed for use with metal studs or cinderblock walls. If you
are uncertain or unknowledgeable about the construction of your wall, then
please consult a qualified contractor or professional installer for assistance.
The wall you are mounting to must support 4 times the weight of the total
load. The load is defined as the TV and Mount along with anything else
suspended from the mount. If not, then the surface must be reinforced to meet
this standard. The installer is responsible for verifying that the wall
structure and hardware used in any installation method will safely support the
total load.
If you get stuck, give customer service a call at
1-855-816-6868
You can also reach us at
contact@suncraftsolutions.com
www.stanleytvmounts.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>