LALUZ A02899 Outdoor Pendant Lights Farmhouse Ceiling Hanging Porch Fixture Instruction Manual
- June 1, 2024
- LALUZ
Table of Contents
LALUZ A02899 Outdoor Pendant Lights Farmhouse Ceiling Hanging Porch Fixture
WARNING
WARNING (To reduce the risk of fire, electric shock, or injury to persons):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
- Mounting surface should be clean, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
- Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
- Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
- When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
Before doing assembly and installation please prepare the needed tools as below picture
-
Ladder
-
Phillips head. flat blade screwdriver
-
Electrical tape
-
Pliers
-
Wire cutter/Stripper
PARTS TYPE & QTY INCLUDING
- (A) Mounting plate (1)
- (B) Green ground screw (1)
- (E) Canopy (1)
- (F) knob nut (2)
- (G) Chain (1)
- (H) Quick link (2)
- ( I ) Loop (2)
- (J ) Screw (2)
- (K) Roof (1)
- (L) Cage (1)
- (M)Glass (1)
- (N) Finial (1)
ACCESSORIES & QTY ENCLOSED
- (C) Mounting screw (2)
- (D)Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Make pre-installation
Step A1: By measuring, determine the correct length of wires needed. Use the wire pliers, cut and discard the remaining wires.
Step A2: Attach a quick link(H) to loop(I) on the top of cage and to connect the end of chain(G). Attach a quick link(H) to loop(I) on the canopy(E) and to connect the end of chain(G).
Step A3: Gently lace wires through the chain (G) to the top of another quick link(H)
Step A4: If needed, cut off the wires length of fixture. At this point, need take note of length should be available for the following mounting. the length from the top of nipple are at least 6″
-
Turn off power
Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position. -
Make installation
StepB1: Unscrew the screw (I) from roof (K)then remove cage (L)
Step B2: Install bulb (Not included. Please do not exceed the maximum capacity recommended on the socket.) Set roof down on top of cage (L).
Thread the screws down through holes in roof and into cage (L). Tighten screws (I) to secure roof (K) in place.
Step B3 : Unscrew knob nuts (F)from canopy(E) then gently remove mounting plate (A) from canopy(E)
Step B4: Attach mounting plate (A) to outlet box with mounting screw (C). The side of single bar marked “GND” must face out
Step B5: Make wire connections
Connect wires as below wires connecting shown. TAKE NOTE OF YOUR COLOR OF FIXTURE , NEVER CONNECT WIRES TO GROUND WIRES
Connect ground wire according to below chart
Connect wires according to below chartConnect Black or Red Supply Wire to:| Connect Wl1ite Supply Wire to:
---|---
Black| Wt1ite
- Parallel cord (round & sn1ooth)| *Parallel cord (square & ridged)
Parallel cord (square & ridged) without tracer| Clear, Brown. Gold or Black with tracer
insulated wire (other than green) with copper conductor| insulated wire (other than green} with silver conductor
*Note: When parallel wires (SPT I & SPT II) are used. The neutral wire is square shaped or ridged and the other wire will be round it shape or smooth ( see illuis).
Twist plastic wire connector until wires are tightly joined together, wrap
each connector with approved electrical tape. Be sure that no wire strands are
exposed and then carefully tuck all wires into the outlet box .
Step B6: Raise canopy (E) to ceiling and secure canopy (E) in place by
tightening knob nut (F)
- Check everything installed properly, then you could turn on the light. Enjoy!
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not
use abrasive materials such as scouring pads or powders, steel wool or
abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when ordering parts.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>