LALUZ B08TG5GLDD Modern Farmhouse Chandelier Instruction Manual
- June 16, 2024
- LALUZ
Table of Contents
LALUZ B08TG5GLDD Modern Farmhouse Chandelier Instruction Manual
WARNING ( To reduce the risk of fire, electric shock, or injury to persons):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
- Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
- Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
- When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before doing assembly and installation please prepare the needed tools as below picture.
| | | |
---|---|---|---|---
Ladder| Phillips head. flat blade screwdriver| Electrical tape| Pliers| Wire
cutter/Stripper
PARTS TYPE & QTY INCLUDING:
(C) Round mounting plate (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Loop(4)
(G) Knob nut (2)
(H) Upper stem
(I) Iron plate (2)
(J) Tapping screw (8)
(K) Hex nut (8)
(L) Upper wooden frame (1)
(M) Batten (4)
(N) Shorter iron frame (2)
(O) Longer iron frame (2)
(P) Lower wooden frame (1)
(Q) Lower stem (2)
(R) Tube (1)
(S) Quick link (2)
ACCESSORIES & QTY ENCLOSED:
(A) Plastic wire connector (3)
(B) Mounting screw (2)
(T) Wrench (1)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Make pre-installation
Step A1: Pass the batten (M) through the lower wooden frame (P) and secure with a hex nut (K).
Step A2: Clip longer iron frame (O) and shorter iron frame (N) into the wood frame. Pass the batten (M) through the upper wooden frame (L) and secure with a hex nut (K).
Step A3: Carefully pass the power cord through the lower stem (Q), then twist the lower stem (Q) onto the tube (R). Insert the lower stem (Q) into the iron plate (I) and tighten it with the upper stem (H)
Turn off power
Before you start to make installation, NEVER attempt any work without
shutting off the electricity until the work is done.
A). Go to the main fuse, or circuit breaker, box in your home. Place the
main power switch in the “OFF” position.
B). Place the wall switch in the“ OFF” position.
Make installation
Step B1: Unscrew the knob nuts(G) from mounting plate (C) .
Step B2: Attach the mounting plate(C) to outlet box with the mounting screws(B).
Step B3: If needed, cut off the wires length of fixture.At this point, the remaining wire length measured from the top single bar(C) is at least 6″.
Step B4: Make wire connections Connect wires as below wires connecting shown. **TAKE NOTE OF YOUR WIRE COLOR OF FIXTURE ,NEVER CONNECT WIRE TO GROUND WIRE
Connect ground wire according to below chart
Connect wires according to below chart
**
| Connect Black or Red Supply Wire to: | Connect White Supply Wire to: |
|---|---|
| Black | White |
| *Parallel cord (round & smooth) | *Parallel cord (square & ridged) |
| Clear, Brown, Gold or Black without tracer | Clear, Brown, Gold or Black with |
tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other
than green) with silver conductor
***Note: When parallel wires (SPTI & SPT II) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
Twist plastic wire connector until wires are tightly joined together, wrap
each connector with approved electrical tape. Be sure that no wire strands are
exposed and then carefully tuck all wires into the outlet box .
Step B5:** Raise canopy (E) to ceiling and secure canopy (E) in place by
knob nut (G) onto the threaded nipple on mounting plate.
Step B6 : Install bulbs (not included) (Please do not exceed the maximum capacity recommended on the socket.)
Check y thing is already installed properly, then you could turn on the light. Enjoy!
CLEANING.
To clean, wipe fixture with a soft cloth. Do not use abrasive materials such
as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS.
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>