LALUZ A03376.79 Bathroom Vanity Light Fixtures Instruction Manual
- June 17, 2024
- LALUZ
Table of Contents
LALUZ A03376.79 Bathroom Vanity Light Fixtures
WARNING (To reduce the risk of fire, electric shock, or injury to persons):
- We suggest installation by a licensed electrician.
- Please read the instructions carefully and save them as you may need them at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
- The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before the fixture.
- Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
- Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
- When replacing the bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
PRODUCT
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED):
Before doing assembly and installation please prepare the needed tools as
below picture
PARTS TYPE & QTY INCLUDING
- (E) Mounting plate (1)
- (F) Green ground screw (1)
- (G) Backplate (1)
- (H) Knob nut (2)
- (I) Socket (3)
- (J) Screw (9)
- (K) Wire lampshade (3)
ACCESSORIES & QTY ENCLOSED:
- (A) Plastic wire connector (3)
- (B) Anchor (4)
- (C) Mounting screw (2)
- (D) Wood screw (4)
- (J) Screw (1) spare parts
ASSEMBLY & INSTALLATION INSTRUCTIONS
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Turn off power Before you start to make an installation, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
- Make installation
-
Step A1 : Unscrew the knob nuts (H) from the back plate(G) then gently remove the mounting plate (E).
-
Step A2 : Carefully pass wires from the outlet box through the mounting plate (E). By measuring, determine the correct distance of the drilling hole for anchor (B) knocked into wall, then drill holes and gently knock the anchors into wall until them are level to the wall.
Attach the mounting plate (E) to outlet box with mounting screws (C) and wood screws(D). -
Step A3: Make wire connections Connect wires as below wires connecting shown. TAKE NOTE OF THE WIRE COLOR OF THE FIXTURE,NEVER CONNECT
WIRE-TO-GROUND WIRE Connect ground wire according to the below chart
Connect wires according to the below chart
*Note: When parallel wires (SPT | & SPT II are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.) When parallel wires (SPT | & SPT II are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
Twist the plastic wire connector until wires are tightly joined together, and carefully tuck all wires into the outlet box
- Step A4 : Put the back plate (G) to the wall, carefully pass the threaded nipple through holes in the back plate and secure them with knob nuts(H).
- Step A5 :Fix the wire lamp shade (K) to the socket (I) with screws (J). Install bulb (Not included. Please do not exceed the maximum capacity recommended on the socket.)
Check everything is installed properly, then you can turn on the light. Enjoy!
CLEANING
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>