LALUZ A03409 Bathroom Vanity Light Fixtures Instruction Manual

June 17, 2024
LALUZ

LALUZ A03409 Bathroom Vanity Light Fixtures

LALUZ A03409 Bathroom Vanity Light Fixtures

SAIFETY INFORMATION

WARNING (To reduce the risk of fire, electric shock, or injury to persons):

  1. We suggest installation by a licensed electrician.
  2. Please read the instruction carefully and save it as you may need it at later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
  4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
  5. Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
  6. Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
  7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
  8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

Image For Finished Product

TOOLS REQUIRED (NOT INCLUDED)

Before doing assembly and installation please prepare the needed tools as below picture.

  • Ladder
    Tools

  • Phillips head, flat blade screwdriver
    Tools

  • Electrical tape

  • Pliers
    Tools

  • Wire cutter/Stripper
    Tools

PARTS TYPE & QTY INCLUDING

(A) Mounting plate (1)
(B) Green ground screw (1)
(E) Stud (4)
(F) Back plate (1)
(G) Socket ring (3)
(H) Glass (3)
(I) Socket (3)
Parts Type & Qty Including

ACCESSORIES & QTY ENCLOSED

(C) Mounting screw (2)
(D) Plastic wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration

  2. Turn off power
    Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.

  3. Make assembly & installation
    Step 1: Unscrew the studs (E) from back plate(F)
    then gently remove mounting plate (A)

Step 2 :Carefully pass outlet box wires through mounting plate (A) Attach back plate (A) to outlet box with mounting screws (C)

Step 3: Make wire connections
Connect wires as below wires connecting shown. TAKE NOTE OF YOUR WIRE COLOR OF FIXTURE ,NEVER CONNECT WIRE TO GROUND WIRE
Connect ground wire according to below chart 

Connect wires according to below chart

Connect Black or Red Supply Wire to: Connect White Supply Wire to:
Black White
*Parallel cord (round & smooth} *Parallel cord (square & ridged)
Clear. Brown, Gold or Black without tracer Clear. Brown. Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

| Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
Assembly & Installation Instructions
Twist plastic wire connector until wires are tightly joined together, wrap each connector with approved electrical tape and carefully tuck all wires into the outlet box.
Step 4: Put the back plate (E)on the mounting plate(A) and gently adjust the back plate (F) till the holes in plate and (A) and backplate (F) are aligned ,then secure it with studs(E)

Step 5: Place the glasses (H)over sockets(I)then secure with the retaining socket rings (G) Install bulb (Not included. Please do not exceed the maximum capacity recommended on the socket.)

  1. Check everything is installed properly, then you could turn on the light Enjoy!
    CLEANING
    To clean, wipe fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
    ORDERING PARTS
    Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals