LALUZ 15 2 Light Bathroom Vanity Light Instruction Manual
- June 17, 2024
- LALUZ
Table of Contents
LALUZ 15 2 Light Bathroom Vanity Light
Product Information
Specifications:
- Part (C) Green ground screw (1)
- Part (D) Mounting plate (1)
- Part (E) Back plate (1)
- Part (F) Knob nut (2)
- Part (G) Socket (2)
- Part (H) Screw (6)
- Part (I) Wire lampshade (2)
Product Usage Instructions
Tools Required (Not Included):
Before starting assembly and installation, please prepare the needed tools
as shown in the provided picture.
Assembly & Installation Instructions:
- Step 1: Carefully remove the fixture from the carton and ensure all parts and accessories are included.
- Step 2: Turn off power by switching off the main power switch and wall switch.
- Step 3: Make assembly:
- Step A1: Unscrew knob nuts (F) from back plate (E) and set them aside.
- Step A2: Pass supply wires through mounting plate (D) and secure it to the outlet box with mounting screws (A).
- Step A3: Connect wires as instructed in the manual, ensuring proper connections and using plastic wire connectors and electrical tape.
- Step A4: Align back plate (E) with mounting screws, attach back plate to mounting plate using knob nuts, and tighten.
- Step A5:
- Attach wire lampshades (I) and sockets (G), securing them with screws (H).
- Install bulbs (not included) without exceeding the recommended wattage.
- Step 4: Ensure everything is installed correctly before turning on the light.
Cleaning :
To clean, wipe the fixture with a soft cloth. Avoid abrasive materials like
scouring pads or steel wool.
Ordering Parts:
Keep the manual for future reference when ordering replacement parts. All
parts can be ordered from the place of purchase using the exact wording from
the illustration.
Frequently Asked Questions (FAQ):
-
Q: Can I install the fixture without the help of a licensed electrician?
A: While it is recommended to have a licensed electrician install the fixture, if you follow the provided instructions carefully and adhere to safety precautions, you can attempt installation on your own. -
Q: What should I do if I exceed the recommended bulb wattage?
A: It is crucial not to exceed the maximum wattage recommended on the socket to prevent damage or hazards. If you accidentally exceed the wattage, immediately replace the bulb with a lower wattage one.
Instructions
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools as
below picture
PARTS INCLUDING
- (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Back plate (1)
- (F) Knob nut (2)
- (G) Socket (2)
- (H) Screw (6)
- (I) Wire lampshade (2)
ACCESSORIES ENCLOSED:
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
- (H) Screw (1) (Spare parts)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done. -
A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
-
B) Place the wall switch in the “OFF” position.
-
Make assembly
-
Step A1: Unscrew knob nuts (F) from back plate (E), then set them aside for later installation.
-
Step A2 : Carefully pass the supply wires from the outlet box through mounting plate (D). Secure mounting plate (D) to the outlet box with mounting screws (A).
-
Step A3: Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Connect wires according to the below chart
Twist
wires together with plastic wire connectors until tightly joined, and wrap
each connector with approved electrical tape. Be sure that no wire strands are
exposed and then carefully tuck all wires into the outlet box. -
Step A4: Align the holes in back plate (E) with the preassembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.
NOTE: back plate (E) should be snug against the wall with knob nuts (F). If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate assembly (D) by unscrewing the pre-assembled hex nuts and then screwing the pre-assembled mounting screws in or out of mounting plate (D) until the secure length is achieved.
Tighten the pre-assembled hex nuts and back to Step A4. -
Step A5:
-
Attach wire lampshades (I) and sockets (G) and secure them with screws (H).
-
Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
-
Check everything is installed properly, then you could turn on the light. Enjoy!
CLEANING
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustration when ordering parts.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>