LALUZ TWIG100603 Farmhouse Chandelier 5 Light Chandeliers for Dining Room Instruction Manual

LALUZ TWIG100603 Farmhouse Chandelier 5 Light Chandeliers for Dining Room

Product Usage Instructions

Assembly & Installation Instructions:

Carefully remove the fixture from the carton and check that all parts and accessories are included.

1. Step A1: Pass the batten through the lower wooden frame and secure with a hex nut.
2. Step A2: Clip longer iron frame and shorter iron frame into the wood frame. Pass the batten through the upper wooden frame and secure with a hex nut.
3. Step A3: Pass the power cord through the lower stem, then twist the lower stem onto the tube. Insert the lower stem into the iron plate and tighten it with the upper stem.
4. Step B1: Unscrew the knob nuts from the mounting plate.
5. Step B2: Attach the mounting plate to the outlet box with the mounting screws.
6. Step B3: If needed, cut off the wires length of fixture. Make wire connections as instructed.
7. Step B4: Raise canopy to ceiling and secure it in place by knob nut onto the threaded nipple on mounting plate.
8. Step B5: Install bulbs (not included) without exceeding the maximum capacity recommended on the socket.

Cleaning

• To clean, wipe fixture with a soft cloth.
• Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

Ordering Parts

• Keep this sheet for future reference.
• All parts for this fixture can be ordered from the place of purchase using the exact wording from the illustration when ordering parts.

FAQ

Frequently Asked Questions

• Q: Can I install the product without the help of a licensed electrician?
  • A: It is suggested to have the product installed by a licensed electrician to reduce the risk of fire, electric shock, or injury to persons.
• Q: How should I clean the fixture?
  • A: Wipe the fixture with a soft cloth. Avoid using abrasive materials like scouring pads, steel wool, or abrasive paper.
• Q: What should I do if I need to order replacement parts?
  • A: Keep this sheet for future reference. You can order all parts for this fixture from the place of purchase using the exact wording from the illustration when ordering parts.

Safety Information

WARNING: (To reduce the risk of fire, electric shock, or injury to persons):

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
6. Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED

TOOLS REQUIRED (NOT INCLUDED):

Before doing assembly and installation please prepare the needed tools as below picture

Product Description

PARTS TYPE & QTY INCLUDING

• (C) Round mounting plate (1)
• (D) Green ground screw (1)
• (E) Canopy (1)
• (F) Loop(4)
• (G) Knob nut (2)
• (H) Upper stem
• (I) Iron plate (2)
• (J) Tapping screw (8)
• (K) Hex nut (8)
• (L) Upper wooden frame (1)
• (M) Batten (4)
• (N) Shorter iron frame (2)
• (O) Longer iron frame (2)
• (P) Lower wooden frame (1)
• (Q) Lower stem (2)
• (R) Tube (1)
• (S) Quick link (2)

ACCESSORIES & QTY ENCLOSED

• (A) Plastic wire connector (3)
• (B) Mounting screw (2)
• (T) Wrench (1)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
2. Make pre-installation
3. Step A1: Pass the batten (M) through the lower wooden frame (P) and secure with a hex nut (K).
4. Step A2: Clip longer iron frame(O) and shorter iron frame(N) into the wood frame.

  * Pass the batten (M) through the upper wooden frame (L) and secure with a hex nut (K).
3.  **Step A3:** Carefully pass the power cord through the lower stem (Q), then twist the lower stem (Q) onto the tube (R).
  * Insert the lower stem (Q) into the iron plate (I) and tighten it with the upper stem (H).

3. Turn off power
   Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the“OFF” position.

Make installation

• Step B1: Unscrew the knob nuts(G) from mounting plate (C) .
• Step B2: Attach the mounting plate(C) to outlet box with the mounting screws(B).
• Step B3: If needed, cut off the wires length of fixture.At this point, the remaining wire length measured from the top single bar(C) is at least 6″.
• Step B4: Make wire connections
  • Connect wires as below wires connecting shown. TAKE NOTE OF YOUR WIRE COLOR OF FIXTURE ,NEVER CONNECT WIRE TO GROUND WIRE
  • Connect ground wire according to below chart
  • Connect wires according to below chart
  • Twist plastic wire connector until wires are tightly joined together,wrap each connector with approved electrical tape.Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box .
• Step B5: Raise canopy (E) to ceiling and secure canopy (E) in place by knob nut (G) onto the threaded nipple on mounting plate.
• Step B6: Install bulbs (not included) (Please do not exceed the maximum capacity recommended on the socket.)

Check anything is already installed properly, then you can turn on the light. Enjoy!

CLEANING

To clean, wipe fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.

References

• The domain name tape.be is for sale | Dan.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>