LALUZ Farmhouse Chandelier Installation Guide

LALUZ Farmhouse Chandelier

Product Information

Specifications:

• Single bar (E): 1
• Green ground screw (F): 1
• Hex nut (A): 1
• Nipple (C): 1
• Canopy (G): 1
• Collar ring (H): 1
• Collar loop (I): 1
• Quick link (J): 2
• Upper chain (K): 1
• Upper bead strand assembly (L): 1
• Fixture (M): 1
• Lower bead strand assembly (N): 1
• Cover (O): 1
• Threaded nut (P): 1
• Wood drop (Q): 1
• Mounting screw (B): 2
• Plastic wire connector (D): 3

Product Usage Instructions

Assembly & Installation Instructions:

1. Remove Fixture: Carefully remove the fixture from the carton and ensure all parts are included.
2. Assemble: If parts are not pre-assembled, follow these steps:
   • Step A1: Thread the single bar (E) over the nipple (C) ensuring the side marked GND faces down.
   • Step A2: Thread the hex nut (A) onto the nipple (C) till snug.
   • Step A3: Thread the collar loop (I) onto the nipple (C).
3. Pre-Installation:
   • Step B1: Thread the fixture (M) onto the threaded nipple on the fixture body.
   • Step B2: Secure lower bead strand assembly (N) and cover (O) using hex nut and threaded nut respectively. Hang the wood drop onto the threaded nut.
4. Installation:
   • Step C1: Attach the single bar (E) to outlet box with mounting screws (B). Ensure the side marked GND faces out.
   • Step C2: Raise the canopy (G) through screw collar loop (I) and position it correctly.
   • Step C3: Attach threaded ring (H) over chain (K) and canopy (G).
   • Step C4: Connect quick link (J) to loop (I) and pass wires through screw collar loop (H).
   • Step C5: Cut off excess wire length if needed.

Frequently Asked Questions

Q: Can I install the product without a licensed electrician?

A: For safety reasons, it is recommended to have the product installed by a licensed electrician to reduce the risk of fire, electric shock, or injury.

Q: What tools are required for assembly and installation?

A: The tools required include a ladder, Phillips head screwdriver, flat blade screwdriver, wire cutter/stripper, pliers, and any other tools specified in the instruction manual.

Q: How do I ensure proper positioning of the canopy and collar loop during installation?

A: Follow step C2 in the installation instructions to position the canopy correctly against the ceiling and adjust the collar loop on the single bar assembly as needed for secure hanging.

WARNING (To reduce the risk of fire, electric shock, or injury to persons):

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products

TOOLS REQUIRED

TOOLS REQUIRED (NOT INCLUDED):

Before doing assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

• (E) Single bar (1)
• (F) Green ground screw (1)
• (A) Hex nut (1)
• (C) Nipple (1)
• (G) Canopy (1)
• (H) Collar ring (1)
• (I) Collar loop (1)
• (J) Quick link (2)
• (K) Upper chain (1)
• (L) Upper bead strand assembly (1)
• (M) Fixture (1)
• (N) Lower bead strand assembly (1)
• (O) Cover (1)
• (P) Threaded nut (1)
• (Q) Wood drop (1)

ACCESSORIES & QTY ENCLOSED:

• (B) Mounting screw (2)
• (D)Plastic wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and
   accessories are included as shown in the above illustration

2. Make assembly
   If the group of parts are not already assembled

   • Step A1: Thread the single bar(E) over the nipple (C) a minimum of 6 mm (1/4”). At this point need note that: the side of single bar marked “GND” must face to the down.
   • Step A2:Thread the hex nut (A)onto the nipple (C) till snug.
   • Step A3:Thread the collar loop (I) onto the nipple (C).

3. Make pre-installation

   • Step B1: Thread the fixture (M)onto the threaded nipple on the fixture body (M) Carefully hang the bead strands onto the fixture body (M)
   • Step B2: Position the lower bead strand assembly (N)over the threaded end of fixture body(M) ,then secure with the hex nut.Position the cover (O) over the threaded end of fixture body(M),then secure with the threaded nut(P) . Hang the wood drop onto the threaded nut (P).
   • Step B3: By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the remaining chain.
   • Step B4: Carefully lace the wires through the chain (K)(every other link)and stop just before you reach the top of chain (K). Gently pull the wires till snug .4. Turn off power Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done.
   • A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the“OFF” position

4. Make installation

   • Step C1: .Attach the single bar (E) to outlet box with mounting screws (B). The side of single bar marked “GND” must face out
   • Step C2: Raise the canopy (G) through screw collar loop (I) and screw the collar loop (I) to a proper position by measuring . Unscrew the threaded ring (H) from screw collar loop (I) and remove the canopy (G). In this way, you would know the Proper position on which collar loop it should be located .
   • Note: The canopy (G) should be snug against the ceiling and the collar loop (I) should be screwed enough threads (no less than 6 threads )over the threaded nipple (C) for more secure hanging .If not, adjust the collar loop (I) on the single bar assembly (E) by screwing the collar loop (I) in or out of the single bar (E) until the length is achieved.
   • Step C3: Slip the threaded ring(H) over the chain(K),then do the same with the canopy(G)
   • Step C4: Open the quick link(J)，attach the quick link (J) to connect the loop (I). Close the quick link(J) Pass the wires through screw collar loop(H) to the top of nipple(E) and gently pull till snug.
   • Step C5: If needed, cut off the wires length of the fixture.At this point, the remaining wire length measured from the top of single bar(B) is at least 6″.
   • Step C6: Make wire connections
     Connect wires as below wires connecting shown. TAKE NOTE OF THE COLOR OF FIXTURE , NEVER CONNECT

WIRES TO GROUND WIRES

Connect ground wire according to below chart

Connect wires according to below chart

Twist plastic wire connector(D) until wires are tightly joined together,wrap each connector with approved electrical tape for more secure connection, then carefully stuff all wires into the outlet box

• Step C7: Raise canopy (G) to ceiling and secure canopy (G) in place by tightening threaded ring (H) onto collar loop (I)
• Step C8: Install bulbs (not included) (Please do not exceed the maximum capacity recommended on the socket.)

Check everything is already installed properly, then you could turn on the light. Enjoy !

CLEANING

To clean, wipe fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>