LALUZ A03410 Bathroom Vanity Light Fixtures Instruction Manual

A03410 Bathroom Vanity Light Fixtures

WARNING (To reduce the risk of fire, electric shock, or injury to persons):

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
6. Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT：

TOOLS REQUIRED (NOT INCLUDED):
Before doing assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING:

(A)Mounting plate (1)
(B) Green ground screw (1)
(E) Stud (4)
(F) Back plate (1)
(G) Socket ring (4)
(H ) Glass (4)
( I ) Socket (4)

ACCESSORIES & QTY ENCLOSED:

(C) Mounting screw (2)
(D) Plastic wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS:

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration

2. Turn off power
   Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the“OFF” position.

3. Make assembly & installation
   Step 1 : Unscrew the studs (E) from back plate(F) then gently remove mounting plate (A) Step 2 :Carefully pass outlet box wires through mounting plate (A)
   Attach back plate (A) to outlet box with mounting screws (C) Step 3 : Make wire connections
   Connect wires as below wires connecting shown.
   TAKE NOTE OF YOUR WIRE COLOR OF FIXTURE ,NEVER CONNECT WIRE TO GROUND WIRE
   Connect ground wire according to below chart Connect wires according to below chart
   Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
   ---|---
   Black| White
   *Parallel cord ( round & smooth )| Parallel cord ( square & ridged )
   Clear,Brown,Gold or Black without tracer| Clear,Brown,Gold or Black with tracer
   Insulated wire ( other than green ) with copper conductor| Insulated wire ( other than green ) with silver conductor

‘ Note : When parallel wires ( SPT I & SPT II) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth ( see illus.) Twist plastic wire connector until wires are tightly joined together,wrap each connector with approved electrical tape and carefully tuck all wires into the outlet box.
Step 4: Put the back plate (E)on the mounting plate(A) and adjust the back plate (F)to secure the holes to be aligned then secure it with studs(E) Step 5: Place the glasses(H)over sockets(I)then secure with the retaining socket rings (G)
Install bulb (Not included. Please do not exceed the maximum capacity recommended on the socket.)

4. Check everything is already installed properly, then you could turn on the light.

CLEANING

To clean, wipe fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>