FORGING MOUNT MD8748L 48 Inch Extension Long Arm TV Wall Mount Instruction Manual

FORGING MOUNT MD8748L 48 Inch Extension Long Arm TV Wall Mount

Getting Started

Does your TV (including accessories) weight more than 110 lbs. (50 kg )?

• No — Perfect!
• Yes- This mount is NOT compatible.

WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the weight of the TV (with accessories) does not exceed 110 lbs (50 kg ).

What is your wall made of?

Please read through these instructions completely to be sure you’re comfortable with this easy install process. Also, check your TV owner’s manual to see if there are any special requirements for mounting your TV. If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact US via: forgingmount888@163.com

CAUTION: Avoid potential personal injuries and property damage!

• This product is designed for use in wood stud/concrete walls DO NOT install it into drywall
• The wall must be capable of supporting five times the weight of the TV and mount combined
• Do not use this product for any purpose not explicitly specified by the manufacturer
• Manufacturer is not responsible for damage or injury caused by incorrect assembly or use

Tools Needed

Hardware Included

WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts!

NOTE: Not all parts and hardware included will be used.

INSTALLATION INSTRUCTION

STEP1-1 Select TV Screw Diameter
Hand thread screws into the threaded inserts on the back of your TV to determine which screw diameter ( M6, or M8) to use.

STEP1-2 Select TV Screw Length
If your TV has a flat back, AND you want your TV closer to the wall, use the shorter screws (A). Use the spacers and longer screws(B) to accommodate:

• Round/irregular back TVs
• TVs with inset mounting holes
• Extra space needed for cables

Standard configurations are shown. For special  applications, or if you are uncertain about your hardware selection, you can contact at: forgingmount888@163.com

CAUTION: Verify adequate thread engagement with the screw/ washer/spacer combination AND TV bracket.

• Too short will not hold the TV.
• Too long will damage the TV.

STEP1-3 Attach the TV plate to the arm assembly

TV plate connected with arm

STEP 2 Wall Plate Install Wood Stud),

CAUTION: Avoid potential personal injuries and property damage!

• Drywall covering the wall must not exceed 5/8 in. (16 mm)

• Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1 x 3½ in. (38 x 89 mm)

• CAUTION: Avoid potential personal injury or property damage! All lag bolts A MUST BE firmly tightened to prevent unwanted movement of the wall plate 01.

• CAUTION: Ensure the wall plate is securely fastened to the wall before continuing to the next step.

• Locate your studs. Verify and mark the centre of the studs by finding the stud edges using an awl, a thin nail, or an edge-to-edge stud finder.

• Position template 04 at your desired height and line up the holes with your stud centre line. Level the wall plate and mark the holes.

• Drill pilot holes using a 7/32 in (5.5mm) diameter drill bit.
  IMPORTANT Pilot holes must be drilled to a depth of 3 in.(75 mm). Be sure to drill into the centre of the stud.

• Install wall plate 01 using lag bolt and washers B. Tighten the lag bolts only until they are pulled firmly against the wall plate 01

STEP 3 Wall Plate Install Solid Concrete or Concrete Block

CAUTION: property damage!

• Minimum solid concrete thickness:8 in.(203mm)
• Minimum concrete block size: 8 x 8 x 16in.(203x203x406mm)
• Minimum horizontal space between fasteners: 16in(406mm).
• Mount wall plate 01 directly onto the concrete surface.
• Position template 04 at your desired height. Level, then mark the four-hole locations.
• Drill four pilot holes using a 3/8 in. (10 mm) masonry drill bit.

IMPORTANT: Pilot holes must be drilled to a depth of 3 in ( 75 mm ). Never drill into the mortar between blocks. ever drill into the mortar between blocks.

• Insert four concrete anchors C (10x60mm) to the wall
  CAUTION: Be sure the anchors are seated flush with the concrete surface.

• Install wall plate 01 with four washers B and screws

• CAUTION: Improper use could reduce the holding power of screwsА DO NOT over-tighten the screws.

STEP 4 Attach TV Brackets to TV back

CAUTION: Avoid potential personal injuries and property damage! DO NOT use a power screwdriver for this step

IMPORTANT: Ensure the TV bracket is securely fastened before moving on to the next step.

STEP 5 Attach the TV to the arm assembly

STEP 6 Tighting locking screws and cable management

CAUTION: Avoid potential personal injury or property damage!

Make sure your locking screws are tightened BEHIND the mounting plate 05 so the TV is securely fastened in place.

STEP 7 Tilt and level adjustment
Loosen the nut with a wrench P to adjust the appropriate tilt /level Angle and tighten the nut

• Made in China.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>