FORGING MOUNT HY9440 Corner TV Mount Instruction Manual

: June 16, 2024
: FORGING MOUNT

Table of Contents

HY9440 Corner TV Mount
Specifications:
Product Usage Instructions:
Tools Needed:
Getting Started:
Wood Stud Installation:
Concrete Installation:
- FAQ:
Q: Does the weight of my TV matter when using this mount?
Q: Can I install this mount on a drywall?
Q: What if I don’t understand the instructions or have doubts

HY9440 Corner TV Mount

Specifications:

Max. VESA: 600X400mm
Max. Distance: 33″ (83.8cm)
Weight capacity: Up to 99 lbs (45kg)

Product Usage Instructions:

Tools Needed:

Tape Measure
Pencil
Screwdriver
Electric Drill
1/2 in (13 mm) Socket Wrench
Stud Finder
Awl
7/32in. (5mm) Wood Drill Bit
Hammer
3/8in. (10mm) Concrete Drill Bit

Getting Started:

Before starting assembly, verify all parts are included and
undamaged. If any parts are missing or damaged, do not return the
damaged item to your dealer; contact Customer Service.
Make sure your TV (including accessories) weighs less than 99
lbs (45kg). If it weighs more, this mount is NOT compatible.
Determine the type of wall you have: drywall with wood studs or
solid concrete/concrete block.
If you have any doubts about the safety of the installation,
assembly, or use of this product, please contact us via:
forgingmount888@163.com

Wood Stud Installation:

Use a stud finder to locate the wood studs on your wall.
Place the drilling template on the wall and align it with the
desired mounting location.
Use a pencil to mark the locations for drilling holes.
Drill pilot holes using a 7/32in. (5mm) wood drill bit.
Attach the wall plate to the wood studs using lag screws and
washers.
Secure the TV mount plate to the arm assembly using bolts,
washers, and a wrench.
Attach the TV bracket to the TV using the appropriate TV
screws, washers, and spacers.
Hang the TV on the wall plate and ensure it is securely in
place.

Concrete Installation:

Use a tape measure to determine the desired mounting location
on the concrete wall.
Place the drilling template on the wall and align it with the
desired mounting location.
Use a pencil to mark the locations for drilling holes.
Drill pilot holes using a 3/8in. (10mm) concrete drill
bit.
Insert wall anchors into the drilled holes.
Attach the wall plate to the wall anchors using lag screws and
washers.
Secure the TV mount plate to the arm assembly using bolts,
washers, and a wrench.
Attach the TV bracket to the TV using the appropriate TV
screws, washers, and spacers.
Hang the TV on the wall plate and ensure it is securely in
place.

FAQ:

Q: Does the weight of my TV matter when using this mount?

A: Yes, the weight of your TV (including accessories) should not
exceed 99 lbs (45kg). Exceeding the weight capacity can result in
serious personal injury or damage to equipment.

Q: Can I install this mount on a drywall?

A: No, this product is designed for use in wood stud/concrete
walls. Do not install into drywall.

Q: What if I don’t understand the instructions or have doubts

about the safety of the installation?

A: If you have any doubts or concerns, please contact us via:
forgingmount888@163.com

Tools Needed
Wood Staud Install
Concrete Install
Hardware Included Getting Started
Drilling Template
UP

FULL MOTION TV WALL MOUNT

Instruction Manual V2.0

.PEFM):
Max. VESA: 600X400mm Max. Distance: 33″ (83.8cm)

www.forgingmount.com

Does your TV (including accessories) weigth more than 99 lbs. ( 45 kg ) ? No — Perfect! Yes — This mount is NOT compatible.
99lbs (45kg)
WARNING: Exceeding the weight
capacity can result in serious personal injury or damage to equipment! It is the installers’s responsibility to make sure the weight of the TV (with accessories) does not exceed 99 lbs(45kg).

What is your wall made of ? Dry wall with woodstuds ?
1FSGFDU
Solid concrete or concrete block?

Please read throuth these instructions completely to be sure you’re comfortable with this install process. Also check your TV owner’s manual to see if there are any special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product,please contact US via: forgingmount888@163.com
CAUTION: Avoid potential personal injuries and property damage! This product is designed for use in wood stud/concrete walls DO NOT install into drywall. The wall must be capable of supportingfive times the weight of the TV and mount combined. Do not use this product for any purpose not explicitly specified by manufacturer. Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.

Tape Measure

Pencil

Screwdriver

Electric Drill

1/2 in (13 mm) Socket Wrench

Stud Finder Awl

7/32in. (5mm) Wood Drill Bit

Hammer

3/8in. (10mm) Concrete Drill Bit

WARNING:This product

Arm Assembly/ Wall Plate TV Mount Plate Arm Extension

contains small items that could

be a choking hazard if swallowed.

Before starting assembly, verify

all parts are included and

undamaged. If any parts are missing or damaged, do not return

01 x1

02 x1

03 x4

the damaged item to your dealer;

TV Bracket

Wall Plate Template

Level

contact Customer Service.

Never use damaged parts!

NOTE: Not all parts and hardware

included will be used.

05 x2

06 x1

07 x1

Fixed Bracket
04 x2
Velcro Tie
08 x5

Lag Screw
5/16×2.75″
A x4
Lag Screw Washers
B x4
Wall Anchor
C x4

TV Screws

TV Washers

TV Spacers

Allen key

M4X12mm
D x4

M4X30mm
E x4

Ø5 x4 Ø8 x4
J

L 5mm
K x8

L 10mm
L x8

O x1

M6X15mm
F x4

M6X35mm
G x4

Bolts

Washers Wrench

M8X15mm M8X30mm M8X50mm

H x4

I x4

X x4

M5X12mm
M x2

Ø5
N x2

P x1

Step 1-1 Select TV Screw Diameter
Hand thread screws into the threaded inserts on the back of your TV to determine which screw diameter ( M4, M6, or M8 ) to use.
M4 M6 M8

Step 1-2 Select TV Screw Length
If your TV has a flat back, AND you want your TV closer to the wall, use the shorter screws(A). Use the spacers and longer screws(B) to accommodate:
· Round/irregular back TVs · TVs with inset mounting holes · Extra space needed for cables

Standard configurations are shown. For special applications, or if you are uncertain about your hardware selection, you can contact at: forgingmount888@163.com
CAUTION: Verify
adequate thread engagement with the screw/washer/spacer combination and TV bracket. -Too short will not hold the TV. -Too long will damage the TV.

FLAT BACK ROUND BACK INSET HOLES CABLES

Too Short

STEP1-3 4FDVSFUIF57.PVOU1MBUF57#SBDLFUTUPUIFCBDLPG57

Position your TV Mount Plate / TV Backets over your TV hole pattern- making sure the brackets are centered and level over the TV hole pattern.Secure the TV plate or brackets using your screw/washer spacer selectiion: (a) for Flat Back (b) for Round Back/Extra space

Note: If your TV VESA is less than 100x200mm / 4×8 inch, you only need to install a TV Mount Plte. If your TV VESA is more than 100x200mm/4×8 inch or less than 600×400 mm / 23×16 inch, you need to install a TV bracket.
CAUTION: Ensure TV Mount Plate / TV Bracket is securely fastened before moving on to the next step.

(a1) Flat Back

02

(a2) Flat Back

05

D/F/H J

Correct Too Long

(b1) Round Back / Extra Space

02

E/G/I/X J

K/L

Alternate Spacer Setups

(b2) Round Back / Extra Space

05

E/G/I/X J

K/L

Alternate Spacer Setups

Step 2A Wall Plate Instal (Wood Stud) 2A-1
CAUTION: Avoid potential personal injury or property damage! All Lag Screws A MUST BE firmly tightened to prevent unwanted movement of the Wall Plate 01 .
Drywall covering the wall must not exceed 5/8 in.(16mm) Minimum wood stud size: common 2×4 in. (51x102mm) nominal 1×3 in.(38x8omm)

2A-2

2A-3
07 06

3 in. (75mm)

2A-4

07

AB

01

CAUTION: Ensure the Wall Plate 01 is securely fastened to the wall before continuing on to the next step.

Locate your studs. Verify and mark the center of the studs by finding the stud edges using an awl, a thin nail, or an edge-to-edge stud finder.

Position the Wall Plate Template 06 at your desired height and line up the holes with your stud center line. Level the wall plate and mark the holes.

Drill 3 pilot holes using a 7/32 in (5.5mm) diameter drill bit. IMPORTANT: Pilot holes must be drilled to a depth
of 2.36 in.(60mm). Be sure to drill into the center of the stud.

Install wall plate 01 using lag screws A and washers B . Tighten the lag screws only until they are pulled firmly a gainst the wall plate 01 .

Step 2B Wall Plate Instal (Solid Concrete or Concrete Block) 2B-1

Min. 8 in. (203mm)
Min. 16 in. (406mm)

Min. 8 in. (203mm)

07

2B-2

06

2B-3
$

2B-4

“#

CAUTION: Avoid potential personal injuries and property damage!
Minimum solid concrete thickness: 8 in.(203mm) Minimum concrete block size: 8 x 8 x 16 in.(203x203x406mm) Minimum horizontal space between fasteners: 16 in.(406mm) Mount wall plate 01 directly onto the concrete surface.

Position Wall Plate Template 06 at your desired height. Level then mark the four hole locations.

Drill four pilot holes using a 3/8 in. (10 mm) masonry drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2.56 in. (65 mm). Never drill into the mortar between blocks.

Insert four wall anchors C (10x50mm) to the wall
CAUTION: Be sure the anchors are seated flush with the concrete surface.

Install arm assembly / wall plate 01 with four lag screws A and washers B
CAUTION: Improper use could reduce the holding power of lag screws A DO NOT over-tighten the screws.

Step 3A Hang the TV onto the Arm Assembly For VESA 100×200 below TVs
Tighten the Bolts M and washers N to secure the TV to the arm assembly.

Step 3B Secure the Fixed Bracket and Arm Extension to the Arm Assemble/Wall Plate, and Hang the TV to Arm Extension (for large size TVs

04

1.Loosen the pre-assembled bolts S1 of the fixing 1.Remove the screws S2 and hang the TV onto the arm assembly .

S1 bracket 04 .

2.Press the safety locks down, then fasten the removed screw .

2.Secure the fixed bracket and Arm Extension to the

TV Mount Plate 02 .

3.Hang the front support onto the arm assembly, and

S2

tighten the bolts M and

4

O

washers N to secure

the TV to the arm assembly.

NM

04 03
S1

02
I
O

Step 4 Tilt and level adjustment
1. Slightly loosen the bolt M or nut N1 with -FWFM a wrench P .
2. Adjust TV to your desired level and tilt angle. 3. Retighten the bolt M or nut N1 to secure
P the TV in place.

¢

M
5JMU
P
N1

Made in China