FORGING MOUNT FM4541 Heavy Duty Gas Spring Monitor Arm Instruction Manual

FORGING MOUNT FM4541 Heavy Duty Gas Spring Monitor Arm

Specifications

• Model: FM4541
• VESA Compatibility: 7575mm, 100100mm
• Maximum Weight Capacity: 33 lbs

Important Safety Information
Read the entire instruction manual before you start installation and assembly. If you have any questions, contact us via email. Ensure that you have received all parts according to the component checklist before installation. Regularly check the bracket for security and safety at least every three months.

Weight Restrictions
Do not exceed the maximum weight capacity of 33 lbs indicated for the mounting system. Using products heavier than the specified weight may lead to mount failure, causing damage or injury.

Packing List
Ensure all components listed in the packing list are present before installation.

Installation Methods

1. Method 1
   Follow steps 1a-1 to 1a-4 for installation.

2. Method 2:
   For desktops with a hole, follow steps 1b-1 to 1b-2 for installation.

Main Body Installation
Use the provided screws to secure the main body of the monitor arm. Ensure that the bracket is securely attached.

Connect with Monitor
Use a wrench to screw the provided screws into the holes at the back of the monitor. Avoid over-tightening to prevent damage.

Heavy Duty Gas Spring Monitor Arm

INSTALLATION MANUAL

Model：FM4541

Thanks for choosing our product! We strive to provide the best quality and services for our customers. Would you kindly share your experience on Amazon if you are satisfied? If you have any questions, please feel free contact us.

Email: forgingmount888@163.com

We’re ready to help!

IMPORTANT SAFETY INFORMATION

Read the entire instruction manual before you start installation and assembly.If you have any questions regarding any of the instructions or warnings, please contact US via: forgingmount888@163.com

CAUTION
Exceeding the weight capacity can result in serious personal injury or damage to equipment!

1. Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
2. Safety gear and proper tools must be used. This product should only be installed by professionals.
3. Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
4. Use the mounting screws provided and DO NOT OVER-TIGHTEN mounting screws.
5.  This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
6. This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

IMPORTANT
Ensure that you have received all parts according to the component checklist prior to installation. if any parts are missing or faulty, can contact us via: forgingmount888@163.com

MAINTENANCE

Check that the bracket is secure and safe to use at regular intervals.
(at least every three months)

WEIGHT RESTRICTIONS

WARNING
DO NOT exceed the maximum weight indicated. This mounting system is intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in failure of the mount and its accessories, causing possible damage and or injury.

PACKING LIST

Installation Method 1

Installation Method 2 (desktop has a hole for item 2 go through)

Connect with Monitor

Use a wrench (G) to screw the screws (A/B) into the four holes at the back of the monitor to avoid damaging the monitor by over-tightening the screws.

When the display is inserted into the quick release head, make sure the knob is vertical.

After insertion, rotate the knob 90 degrees to the left.

Gas Spring Adjustment

Press the arm to keep it in horizontal position and then use the Allen Key to adjust the screw on the arm. Turn counter-clockwise (”+ ” direction) to increase gas spring tension till can hold the weight of your monitor. Note: You may need to turn the screw by many circles to tighten the arm.

Adjust Tilt (+90°/-45°)

Turn clockwise to tighten
Turn counterclockwise to loose
Loose the screw to adjust tilt to +90°

If the pitching angle too tight or too loose when adjusting the mount, please adjust the screw.

This limit screw can prevent the head from sinking. It can also be disassembled if necessary.
Loose the limit screw out if you want to adjust tilt to -45°

Cable Management

Adjustable Instruction

Thank you again
for choosing this forging mount product!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>