FORGING MOUNT FM4545 Single Monitor Arm Stand Installation Guide
- June 16, 2024
- FORGING MOUNT
Table of Contents
FORGING MOUNT FM4545 Single Monitor Arm Stand
THANK YOU!
Thanks for choosing our product! We strive to provide the best quality and services for our customers. Would you kindly share your experience on Amazon if you are satisfied? If you have any questions, please feel free contact us.
FEATURES
IMPORTANT SAFETY INFORMATION
Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact US via: [email protected]
BE CAREFUL
CAUTION: Exceeding the weight capacity can result in serious personal injury or damage to equipment!
- Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
- Safety gear and proper tools must be used. This product should only be installed by professionals.
- Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
IMPORTANT:
Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, can contact us via: [email protected].
MAINTENANCE:
Check that the bracket is secure and safe to use at regular intervals. (at least every three months)
WEIGHT RESTRICTIONS
|
WARNING
---|---
DO NOT exceed the maximum weight indicated. This mounting system is intended
for use only with the maximum weights indicated. Use with products heavier
than the maximum weights indicated may result in failure of the mount and its
accessories, causing possible damage and or injury.
PACKING LIST
-
(X1)
Base
-
(X1)
Clip Plate -
(X1)
Long Bolt
-
(X1)
Clamp
-
(X1)
Bracket -
(X1)
Lower Arm -
(X1)
Upper Arm
-
(X1)
VESA Plate
-
(X1)
Cable Cover
-
(X1)
Anti-slip Pad
-
M4×10 (×4)
A -
M5×10 (×4)
B -
M8×20 (×1)
C -
M6×10 (×2)
D -
3MM (×1)
E -
4MM (×1)
F -
5MM (×1)
G
Installation Instructions
Installation Method 1 Clamp Installation
Installation Method 2 Grommet Base Installation
Connect with Monitor
Use a wrench (G) to screw the screws (A/B) into the four holes at the back of the monitor to avoid damaging the monitor by over tightening the screws.
-
When the display is inserted into the quick release head, make sure the knob is vertical.
-
After insertion, rotate the knob 90 degrees to the left.
5-1 Case 1：Monitor/Arm Fall Down (After Install Your Monitor)
Press the arm to make it keep it in horizontal position and then use the Allen Key to adjust the screw on the arm.Turn counter-clockwise(”+ ” direction) to increase gas spring tension till can hold the weight of your monitor.
Note: You may need to turn the screw by many circles to tighten the arm.
5-2 Case 2：Monitor/Arm Pops Up (After Install Your Monitor)
Press the arm to make it keep it in horizontal position and then use the Allen
Key to adjust the screw on the arm. Turn clockwise (”- ” direction) to reduce
gas spring tension till can stay the position needed.
Note: You may need to turn the screw by many circles to tighten the arm.
Adjustment
Adjust Flexibility
- Turn clockwise to tighten
- Turn counterclockwise to loose
If the pitching angle too tight or too loose when adjusting the mount, please adjust the screw.
Limit Screw
This limit screw can prevent the head from sinking. It can also be disassembled if necessary.
Cable Management
Adjustable Instruction
Thank you again for choosing this forging mount product!
Customer Support
Email: [email protected]
We’re ready to help!
Documents / Resources
|
FORGING MOUNT FM4545 Single Monitor Arm
Stand
[pdf] Installation Guide
FM4545, FM4545 Single Monitor Arm Stand, Single Monitor Arm Stand, Monitor Arm
Stand, Arm Stand, Stand
---|---