VEVOR WY-890 Sealing Machine Instruction Manual

VEVOR WY-890 Sealing Machine

Product Information

Specifications

• Model: WY-890
• Rated Voltage: AC110V~120V 60Hz (For US users), AC220~240V 50Hz (For Europe users)
• Rated Power: N/A

Product Usage Instructions

Important Safety Instructions
This instruction manual is crucial for your safety and satisfaction. Please follow the safety, installation, maintenance, and troubleshooting steps provided. Pay close attention to all the DANGER, WARNING, CAUTION, and NOTICE statements.

Maintenance

1. If the machine is not in use for an extended period, unplug the power cord from the socket.
2. Cease using the machine if it emits smoke, a peculiar smell, becomes noisy, or shows any other abnormal conditions.

FCC Compliance
This device complies with Part 15 of the FCC Rules. It may not cause harmful interference and must accept any received interference.

FAQ

What should I do if the machine emits smoke?

Please stop using the machine immediately and unplug it from the power source. Contact technical support for assistance.

Can I operate the machine with a different voltage?

No, please ensure to use the correct voltage as specified in the manual to prevent damage to the machine.

How often should I perform maintenance on the sealing machine?

Regular maintenance is recommended as per the instructions in the manual. Additionally, unplug the machine if not in use for an extended period.

We continue to be committed to provide you tools with competitive price. “Save Half”, “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands.

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us: Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

Important safety instructions

This instruction manual is intended for your benefit. Please read and follow the safety, installation, maintenance and troubleshooting steps described within to ensure your safety and satisfaction.
The contents of this instruction manual are based on the latest product information available at the time of publication. The manufacturer reserves the right to make product changes at any time without notice.
Always use common sense and pay particular attention to all the DANGER, WARNING, CAUTION and NOTICE statements in this manual.
Maintain labels. These carry important information. The label on your tool may include the following symbols. The symbols and their definitions are as follows:

WARNING

Prior to using this product, please read and understand all instructions and safety warnings. Improper use may result in serious injury or property damage.
Warnings must be followed carefully to avoid body injury. Improper use may result in electric shock, fire, personal injury and other damage:

1. Keep unplugging when moving the machine.
2. Keep unplugging when installing accessories.
3. Place on a flat and stable platform.
4. Do not use this machine in a hazardous location.
5. Do not use when the machine is not working properly.
6. Do not disassemble and repair this machine.
7. Do not use an unsuitable AC Outlet.
8. Do not touch the heating plate when the machine is working.
9. Do not use it in a humid environment or contact with water Do not infiltrate liquid in the machine to prevent fire or electric shock caused by short circuit.
10. Do not use the power supply that does not meet the rated voltage. The power supply that does not meet the specified voltage may cause fire or electric shock.
11. Ensure that the machine is grounded so as not to cause harm to the body.
12. Do not touch the moving part with your fingers during use in case of injuries.
13. If the machine is not in use for a long time, please unplug the power cord from the socket.
14. Please stop using it if the machine smokes, emits a peculiar smell, or becomes noisy and in other abnormal conditions.
15. if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision
16. Type Z attachment: If the supply cord cannot be replaced. If the cord is damaged the appliance should be scrapped.
17. In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
18. Operating and fixing of this product must be conducted by qualified person.
19. Please install this machine according to our instructions.
20. Once unpack the machine, check it throughout to make sure it is complete.
21. Once unpack the machine, check it throughout to make sure it is complete.
22. Any missing or damage please consult it before operating.
23. The packing material should be placed beyond the reach of children.
24. Please turn off the machine when the operator is absent. FCC INFORMATIONIf you need a repair, please ask for an expert and use the original spare part.
25. Do not rinse the machine with water directly.
26. Clean the surface of stainless steel periodically in appropriate method to prevent any damages brought by oxidization or chemical interference.

FCC INFORMATION

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment!
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This product may cause harmful interference.
2. This product must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this product not expressly approved by the party.responsible for compliance could void the user’s authority to operate the product.
Note: This product has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This product generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception,which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna.
• Increase the distance between the product and receiver.
• Connect the product to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for assistance.

PARAMETER

user)
2| Rated Voltage:| AC220~240V 50Hz( For Europe user)| AC220~240V 50Hz( For Europe user)
3| Rated Power:| 350W| 350W
4| Out Put| 500-650 cups/h| 500-650 cups/h
5| Sealing Diameter| 90mm / 95mm| 90mm / 95mm
6| Maximum Cup Height| 180mm| 190mm
7| Cup sealing parameters| Material: PS; Cup sealing temperature range: 160°C to 190°C;
Material: PE; Cup sealing temperature range: 160°C to 190°C;
Material: PP; Cup sealing temperature range: 160°C to 210°C;
170°c has been highlighted on the label to allow users to quickly select
Note: Cups made of other materials may not be suitable for this device. Please refer to the cup manufacturer’s recommended usage methods to seal the cup before use.

Transportation and storage:
Please handle the appliance with care and avoid any violent vibration, collision or inversion. Storage The places for storage should have good ventilation and no corrosive gas. Long-time Open-air storage is not encouraged, if it is inevitable, measures should be taken to protect the machine from rain and blazing sun.

Installation

1. Voltage
   The actual voltage should be the same as or within the range of 10% on either side of voltage marked on the parameter sticker.

2. Install sets
   The appliance should be placed with power switch(10A)and leakage protector(S30mA) equipped around, and with no stuff around to hinder the operation.

3. Check
   Please check carefully whether spare parts are fasten, the power wire is firmly fixed and the electric connection is in good condition.

Preparation

1. According to the above installation diagram to place the film. Please take care of the positive and negative sides of film, The negative side should be forwarded to the lip of cup. Otherwise, the film will fail to seal the cup.
2. Plug in the machine and turn on the switch of power, lower mould will sent autocratically in the meantime. The heating lamp will be flashed which means the heating tube is working.
3. About 5 minutes later, when the lamp keeps on, it means the setting temperature was reached and automatic sealing operation can be performed. Only can use it by manual sealing operation if the setting temperature is not reached.
4. Selection of cup and sealing film
   • a. Easy ripping film is suitable for sealing the cup of a variety of materials.
   • b. In other cases, the materials of cup must be same as the film. Such as the cup of PP (Polypropylene) must be used with the film of PP.
   • c. the recommended temperature refers to the Parameter form.
5. Switch off the power after finishing the sealing, and the lower mould will go in automatically, then take the plug out.
6. In case there is an accident, never put your hand into the machine when it is working.

Usage instructions

Begin sealing the cup when completing above preparation:

1. Press the button of auto operation, light is on.
2. Put the cup filled liquid into the down plate, then it is sent into the machine by pulling-plate. Do not seal empty cup for testing cause the light cup will be adsorbed on the heating plate and stick the film.
3. The machine will automatically roll the firm, seal the cup, cut the film and output the cup plate, and then the counter displayer will count the quantity.
4. Take out the cup and finish one operation.
   Please confirm that the space between two color patches of the film is no less than 115 mm.

Attention

1. In order to protect the electric system of the machine, don’t rinse it by water; only clean it with cloth and cleaning liquid which contains no corrosive components.
2. Please turn off the machine when the operator is absent .
3. In case there is a short circuit or fault, please plug off the machine and request qualified people to repair it.
4. In case of repair, please ask for an expert and use the original spare part.

Cleaning and maintaining

1. Please check carefully whether the upper mould is clean every day, to prevent the foreign substance from sticking to the mould cause a failure to seal the cup.
2. Please use dry cloth to clean the surface of machine, bottom of plate and put grease on the bearings and moving parts of the machine to make it work more easily.
3. Clean the grooved plate and pulling plate to avoid the damage of upper cutter.
4. Keep the cleanness of electric eye, to avoid the foreign substances interfering the detection of the film cause disoperation.

Introductions of control panel

1. Power button please press this button while using it, the screen will display and lower mould will be sent out, which means the machine enters the standby state.

2. Auto/Manual select//Reset button:

   • a. When the automatic light is on which means the machine got into the state of automatic. After setting the cup, it will send the cup in and complete the whole sealing operation automatically (temperature must be reached to the setting point and the heating lamp keeps on.)
   • b. When the automatic light is on which means the machine gets into the state of automatic. If you press the button of reseal, the machine will get into the state of resealing. The LED light of counting will flash, then press the button of manual, the machine will seal.
   • c. When the manual light is on which means the machine gets into the state of manual. After the cup is put in, then press the button of manual, the machine will seal (without temperature limit).

3. Set button: Setting or changing the faction of machine Up or down buttons: Choosing the function of computer to increase or decrease the quantity.
   Count-reset button: Cleaning out the records of sealing quantity and reset to zero.

4. Count display:

   • a. Display the quantity of sealing cups in normal condition

5. Temperature display

   • a. Display the temperature of heating plate in normal conditions.
   • b. Display the setting point in setting state.
   • c. Display the fault code while fault occurs.

6. Safety door: When the light is on which means the exit was touched.

7. Electric eye: It indicates that electric eye has detected black spot in the film when the light is on.

8. Cup in: The cup entering into the machine when the light is on.

9. Roll film: The machine rolls the film when the light is on.

10. Down: The upper mould pressing and sealing the cup.

11. Up: The upper mould rising and resetting.

12. Cup out: The cup is coming out from the machine

13. Automatic operation: The machine gets into the state of automatic.

14. Manual operation: The machine gets into the state of manual.

15. Heat: The heating lamp will flash when the heating tube is working; And when the lamp keeps on, it means the setting temperature was reached.

Computer setup

Computer function set project:

Setup Method:

1. Press the “S” key for the first time to get into the state of temperature setting: Left shows [00P1 ], Right shows [180 ], choosing the up or down key can adjust the range of temperature.
2. Press the”S” key for the second time to get into the state of counting lock: Left shows [00P2 ], Right shows 000 , choosing the up or down key can change to 001 .
3. Press the “S”key for the third time to get into the state of cup-in time setting: Left shows [00P3 ], Right shows [001 ] for 1 second, choosing the up or down key can adjust the range of time [001 ~003] for 1~3 seconds.
4. Press the “S” key for the fourth time to get into the state of sealing time setting: Left shows [00P4 ], Right shows [001 ] for 1 second, choosing the up or down key can adjust the range of time [001 ~005] for 1~5 seconds.
5. Press the “S”key for the fifth time to get into the state of rolling time setting: Left shows [00P5], Right shows [000 ] which control by electric eye, choosing the up or down key can adjust the range of time [001 ~006] for 1~6 seconds..
6. Press the “S”key for sixth time to save all the settle of previous, the machine will go back to standby state and display the real quantity and temperature.

Code transaction

Fault Code:
This machine was equipped with auto-detect function, the system automatically asks the fault code and alarm when it is out of order.

the film
4| OE4| Failure of down(Micro Switch)
5| OE5| Failure of up(Micro Switch).
6| OE6| Failure of temperature detector
7| OE7| Failure of heater or connect wire
8| OE8| Failure of cup out(Micro Switch).

Fault code elimination method:

OE1: Error of Cup In

1. Micro switch with bad contacts: Change a new Micro switch.
2. Micro switch with the poor contact of connection: Reconnect it.
3. The screw of micro switch has got loose: Tighten the screw.
4. The screw of swing link has got loose cause of skidding: Tighten the screw.
5. The motor of cup in doesn’t work, check the wire and tighten the wire when it’s loose.
6. The motor of cup in doesn’t work, change the motor
7. Guide rails enclosed foreign matter, please clean the matter.

OE2 Error of Safety Door

1. The safety door is stuck with the micro switch: Adjust the safety door
2. Failure of micro switch: Change the micro switch.

OE3 Error of Rolling Firm

1. Electric eye with bad reaction:

a.  please clean the foreign matter if there are.

b.  Adjust the sensitivity adjustment of electric eye to ensure that the light will be on when the black spot pass.

c.  None of them is right, please change the electric eye

2. The firm is installation errors and not placed in the notch: Adjust its setting position.

3. The film can’t move:

a.  The motor of film is running, but the film keeps the same. and the paper cylinder and plastic splint is slipping, please reset the Paper cylinder and plastic splint.

b.  When the motor doesn’t work, check the wire is loose or not. If the connection of wire is right, please change a new motor

OE4 Error of Down

1. The damage of micro switch, change a new one.

2. Micro switch with the poor contact of connection: Reconnect it.

3. The screw of micro switch has got loose: Tighten the screw

OE5 Error of Up

1. The damage of upper micro switch, change a new one.

2. Micro switch with the poor contact of connection: Reconnect it.

3. The screw of micro switch has got loose: Tighten the screw

OE6 Error of Temperature detector

1. Temperature detector with the poor contact of connection: Reconnect it.

2. Thermal line is disconnection: Change it.

3. The issue of circuit board,change it.

OE7 Error of heating

1. The damage of heating plate: change the heating plate

2. Heating plate with the poor contact of connection: Reconnect it.

3. The issue of circuit board, change it.

OE8 Error of Cup Out

1. Micro switch with bad contacts: Change a new Micro switch.

2. Micro switch with the poor contact of connection: Reconnect it.

3. The screw of micro switch has got loose: Tighten the screw.

4. The screw of swing link has got loose cause of skidding: Tighten the screw.

5. The motor of cup in doesn’t work, check the wire and tighten the wire when it’s loose.

6. The motor of cup in doesn’t work, change the motor.

7. Guide rails enclosed foreign matter, please clean the matter.

Trouble shooting

serrated knife
2 The serrated knife has dirt or syrup| Clean the dirt or syrup on the serrated knife
2 The cup is not well sealed, has a small breach and leakage.| 1 There’s residues or foreign objects on the heating plate.| Clean the residues or foreign objects on the heating plate.
2 The temperature of the beverage is too high.| The temperature of the beverage is advised to be or less than 45℃.
3 The film does not stick to the cup.| 1 The temperature is too low.| Increase the temperature, but it is not suggested to be higher than 180℃.
2 The film is reversed. (If the film is reversed, it will stick to the heating plate)| Clean off the film on the heating plate, reinstall the film according to the pattern.
4 The film always rolls, the machine does not come down.| 1 The film is not inside the trough of the sensor.| 1 Reinstall and adjust the film.
2 The black patches pass through the sensor, but the red light of the sensor isn’t on, the sensor is not sensitive.| 2 The sensor is not sensitive, increase the sensitivity. The detailed adjusting method is on the right side of the machine.
3 When the film passes through the sensor, the red light is always on.| 3 The sensor is too sensitive, reduce the sensitivity. The detailed adjusting method is on

the right side of the machine.

5 When you pull out or pull in the tray, the film does not roll.| 1 The machine has entered into protection state, will not make any operation.| Restart the machine, it will quit out the protection state and seal the cup again.

Main Structure

WY-890 Main Structure:

Exploded View Part list (WY-890)

WY-980 Exploded View:

Exploded View Part list (WY-980)

1. Small Motor

| 22. Pinch Cock
---|---
2. Small Gear| 23. Little Screwdriver
3. Top Cover| 24. Screwdriver Holder
4. Back Cover Board| 25. Rocker Baffle
5. Big Motor| 26. Travel Switch Mounting Plate
6. Holding Structure of Motor| 27. Bearing Component of Joint
7. Pulling Plate Motor Connecting Rod| 28. Motor Rocker
8. Pulling Plate Motor Rocker| 29. Rod Connecting Shaft
9. Machine Body| 30. Guide Shaft stiffening Plate
10. film Fixed Plate| 31. Front Board
11. Sensor Holder| 32. Scroll of Film-left
12. Cup in Travel Holder| 33. Wire Cover Plate
13. Sensor| 34. Power Cable
14. Pulling Plate Motor Holder| 35. Control Board
15. Cup in Motor| 36. Panel
16. Rubber Stick| 37. Guide Shaft
17. Scroll of Film-right| 38. Safe Door
18. Right Cover| 39. Pulley Guide Rail
19. Upper Mould Component| 40. Pulling Plate Component
20. Big Gear| 41. Rubber Feet
21. Shaft Sleeve of Film|

WY-890 & WY-980 Circuit diagram

travel switch
Xk4:cupping up travel switch| Xk5:cup entering travel switch| Xk6:cup outcome travel switch

Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia
Imported to the USA: Sanven Technology Ltd. Suite 250. 9166 Anaheim Place, Rancho Cucamonga, CA 91730

SHUNSHUN GmbH
Römeräcker 9 Z2021, 76351
Linkenheim-Hochstetten, Germany

Pooledas Group Ltd
Unit 5 Albert Edward House, The
Pavilions Preston, United Kingdom

Technical Support and E-Warranty Certificate www.vevor.com/support

References

• Contact Us – Official VEVOR Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>