JASKEY CR-360 Wireless Charging LCD Alarm Clock Instruction Manual
- June 10, 2024
- JASKEY
Table of Contents
JASKEY CR-360 Wireless Charging LCD Alarm Clock
Product Information
This device is compliant with Part 15 of the FCC Rules, which sets standards for unintentional electromagnetic radiation from electronic devices. It must adhere to two conditions: (1) it should not cause harmful interference, and (2) it must accept any interference received, even if it causes undesired operation. Any changes or modifications not approved by the responsible party may void the user’s authority to operate the equipment. The device also complies with FCC radiation exposure limits for an uncontrolled environment. It is recommended that the device be installed and operated at a minimum distance of 20cm from the radiator and the user’s body to reduce potential radiation exposure.
Product Usage
Before using the device, ensure that it is installed in compliance with the minimum distance of 20cm between the radiator and your body. Failure to do so may lead to potential radiation exposure. When operating the device, ensure that it does not cause harmful interference to other electronic devices in the vicinity. If interference is detected, adjust the device’s position or contact the manufacturer for assistance. Do not make any changes or modifications to the device without the express approval of the responsible party. Doing so may void your authority to operate the equipment If you have any questions or concerns about operating or installing the device, consult the user manual or contact the manufacturer for assistance.
Wireless Charging LCD Alarm Clock
GENERAL LAYOUT
- Wireless Charging Zone
- lock Display
- USB Charging Port
- Wireless Charging Status Light
- Mood Light Button
- Display Dimmer Button
- Snooze Button
- Mood Light
- Buzzer
- Factory Reset Button (Inside Hole)
- Alarm ON/OFF Switch
- Year Adjust / 12/24 Hours Select Button
- Date Adjust / Minute Adjust Button
- Month Adjust / Hour Adjust Button
- Setting Switch
- Back-Up Battery Cover
- DC Input (USB Type-CJ
FEATURES
- Wireless Charging: Max. Output 15W (A Fast Charging Power Adapter is required)
- USB Port Charging: Max. Output 5V/2A
- Extra Large Display
- Clock Dimmer Display: 3 Brightness Settings (Including Shut Off)
- Night Light with Brightness Control
Date Setting
Slide Setting Switch (15) to ‘DATE SET’ positi_on
The digits on the display showing the calendar start to blink:-
- Press the ‘Year’ button (12), ‘Month’ button (14), and ‘Date’ button (13) to set the calendar on the clock display.
- Once the calendar date is set, slide Setting Switch (15) back to the ‘LOCK’ position.
Dimmer Display
The brightness of the clock display digits can be adjusted from full
brightness to display OFF. Touch the(Display Dimmer) button (06)
simultaneously to select the desired brightness: High – Med – Low – Off.
OPERATION
Power Up
- Plug one end of the USB Type-C cable into the unit.
- Plug the other end of the cable to the power adapter.
Clock Setting
- Setting the clock time
- Slide Setting Switch (15) to the ‘TIME SET’ position. The digits for the clock time start to blink.
- Press the ‘Hour Set’ button (14) or Minute Set button (13) to set the desired time.
- Note : Press and hold the ‘HOUR’ or ‘MINUTE’ button to advance the digits at a quicker speed.
- The once desired time is set, slide Setting Switch (15) back to the ‘LOCK’ position.
- 12/24 clock display format
- Press the ’12/24′ button (12) to select the desired 12 or 24-hour clock display format. For 12 Hours clock display format, it will display the AM or PM icon.
- Mood Light (Night Light)
- The brightness of the ‘Night Light / Mood Light’ can be adjusted.
- Touch (Mood Light) button (05) simultaneously to select the desired brightness: High -Med – Low – Off.
WIRELESS CHARGING
Put the wireless charging product that supports the 0.1 protocol on top of the
clock with the marking The blue light next to the USB socket (below the
display) will turn ON to indicate it is wireless charging.
Note
-
If the blue light is flashing, it means wireless charging is not working. Please check if there is any object obstructing the unit from the wireless charging
area. -
In order to achieve the highest wireless charging power of 15W, it is recommended to use a fast-charging power adapter that supports an output voltage of 9V/12V.
Alarm
-
Setting the alarm time
-
Slide Setting Switch (15) to ‘AL. SET’ (Alarm SET) position.
-
The digits for the alarm time start to blink.
-
Press the ‘Hour Set’ button (14) or the ‘Minute Set’ button (13) to set the desired alarm time.
Note: Press and hold the ‘HOUR’ or ‘MINUTE’ button to advance the digits at a quicker speed. -
Once desired alarm time is set, slide Setting Switch (15) back to the ‘LOCK’ position.
-
Alarm ON/Alarm OFF
-
Slide the ‘ALARM ON/OFF’ switch (11) to ‘AL. ON’ to turn ON the alarm function.
-
The ‘Alarm ON’ icon’ (IMIJ ‘ and ‘Snooze’ icon’ Zz’ will show up on the display to indicate that the alarm and the snooze functions have been activated.
USB Charging
The maximum output for USB charging is 5V/2A. In order to achieve this
charging power, it is recommended to use a USB power adapter that supports
this output.
- Plug one end of the USB charging cable to the USB socket of the alarm clock
- Plug the other end of the cable into the mobile device
- Remove the mobile device once it is fully charged.
Battery Back-Up for clock
The 3V button cell battery (CR-2032) is used as a backup to keep the clock
running during a power outage.
- Use the edge of a small coin and insert it into the slot of the battery cover
- Twist and rotate anti-clockwise to remove the battery cover
- Place the button cell battery (CR-2032) into the battery holder. Make sure it is inserted in the correct polarity.
- Put the battery cover onto the unit and rotate it clockwise to secure it back into place.
Alarm Stop
The alarm sound will beep for 1 minute at the alarm time set. Press any of the
buttons at the back of the unit to stop the alarm sound. The alarm sound will
be shut off for the day and will repeat at the same time for the next day.
Alarm OFF
To stop the daily alarm beeping permanently, slide the ‘ALARM ON/OFF’ switch
to ‘AL. OFF position.
Snooze
When the alarm goes off, press the SNOOZE button to temporarily stop the alarm
sound. The alarm sound will come back again after 5 minutes.
Continue pressing the SNOOZE button to activate the Snooze feature. Otherwise,
press any of the buttons at the back of the unit or let the buzzer sound
for 1 minute to stop the snooze function.
Factory Reset
If you need to restore the unit to the factory setting, please use a paper clip and insert it into the reset hole (10) and press the reset button.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>