Paxcess Orobotic Pool Floor Cleaner User Manual
- June 7, 2024
- Paxcess
Table of Contents
Paxcess Orobotic Pool Floor Cleaner User Manual
Thank you for purchasing PaxcessRobotic Pool Cleaner. If you have any
questions or issues, please contact our customer services team for further
assistance.
Email: service@paxcess.com
Free Call: (US) (877)-756-8666 Service Time: Mon.-Fri.: 9:00-17:00 PST
Facebook: @paxcess
Website: www.paxcess.com
Important Precautions
-
ln order to avoid any accident/damage, it is strongly recommended to fix the power supply unit in 3.Sm away from the swimming pool by using the safety rope (included in the package).
-
ln order to prevent severe damage to the cleaner, never power on the unit when it is outside of the swimming pool.
-
The power cord must be connected to an appropriate earthed socket.
-
Hold the top handle when putting the cleaner into water or lifting out of the water, do not pull the cable. Before power on, make sure to empty the trapped air inside the cleaner (no more air bubbles coming from the cleaner and the cleaner is fully submersed on the pool bottom).
-
Before power on, make sure the filter be assembled in position and cable be fully released to avoid any winding, which could affect the
cleaner’s performance or cause damage. -
Please clean and wash the filter bag every time after use.
-
The cleaner should be stored in a cool and ventilated place, away from direct sunlight when not in use.
-
The power supply unit should be placed in a shaded area during working. In order to avoid overheating and potential damage of components, never cover the power supply unit.
-
Only authorized after sales service personnel should open the cleaner’s power supply unit and motor assembly, otherwise the warranty will be invalidated.
-
Do not use the cleaner beyond the working environment/conditions stated in this manual.
-
Make sure the PH of pool water is between 7.0-7.2.
-
This machine is for clean the pool only not for other purpose. Read carefully the user manual before use.
Attention
When put the cleaner into the water please hold the top handle make sure to empty the trapped air inside, then the cleaner can immerse into the pool floor.
When pulling cleaner out of water, suspend the cleaner above water for about 10-15 seconds to empty the water inside. Please holds the top handle only, never pull the cable.
Introduction
The robotic pool cleaner HJ2052 is a new type of highly efficient and energy- saving swimming pool cleaning robot . Through its advanced computer controlled program, it can clean the pool walls and bottom automatically. At the same time, it filters the pool water and gets rid of suspended particles without replace the pool water. It’s totally environmental-friendly.
For safe operation, the cleaner works on 28V direct current. Please read this user manual carefully before use.
Safety
-
Power supply unit position:
Power supply unit needs to be placed in proper position so as to reach the distal end of pool for the cleaner, meanwhile as least 3.5m from pool edge.
-
Free Safety Rope Comes with Machine
Please use the safety rope to fix the power supply unit, which can avoid the power supply unit drop off your pool.
Specifications
Operation instructions
Filter cleaning
-
Slide the two clips according to the indications on the top cover to open it and take out the filters.
-
Clean the filters.
Re-install the filters, pay attention to the good position and slide the two clips to close the top cover. -
Foam Installation
Attention: If your robot is in good performance, please ignore this instruction.
The below instruction is only used for special situation where the robot has difficulties to climb the pool walls.
Stick two foams on the reverse surface of top cover (see below picture), make sure the two foams are in the middle part of top cover.
-
Roller-Foam
In order to ensure the performance of the machine for the first time use, it is normal and all right if the two rollers of the machine are wet at your receipt of the robot. And it is recommended that before each use, if the rollers are dry, please immerse the machine into water for 15-20 minutes and wait for the rollers to fully absorb water, then switch on.
Packing list
Trouble Shooting
The pool water condition must be within the following parameters:
Caution:
Warranty
Email: service@paxcess.com
