GE ETD48GASWWB Capacity Gas Dryer User Manual
- June 1, 2024
- GE
Table of Contents
GE ETD48GASWWB Capacity Gas Dryer
Specifications
- Type: Dryer Accessories
- Sold by: Underwriters Laboratories
- Revised Specifications: 3/24
- Amperage: 30A
Product Usage Instructions
Installation in Alcove or Closet:
- If approved for installation in an alcove or closet, check label on the back of the dryer.
- Dryer MUST be exhausted to the outside.
- Minimum clearances: 0 on either side, 1 front, top, and rear.
- Closet doors must be ventilated with a minimum of 60 sq. in. of open area.
Bathroom or Bedroom Installation:
- Dryer MUST be exhausted outdoors.
- Installation must conform to local codes or National Electric Code and National Fuel Gas Code.
Minimum Clearances (Other Than Alcove or Closet):
- Minimum clearances to combustible surfaces: 0 on both sides, 1 at the rear.
Dryer Exhausting Information:
- Use metal duct only for vertical and horizontal ducting.
FAQ
Q: What are the available power cords for the dryer?
A: GE Appliances recommends using factory-specified power cords to fit your installation requirements. Available options include:
-
* **WX09X10002:** 4′ (1.2m), 30A, 3-wire dryer cord- WX09X10003: 5′ (1.5m), 30A, 3-wire dryer cord
- WX09X10004: 6′ (1.8m), 30A, 3-wire dryer cord
Product Overview
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
EXHAUST OPTION: When viewed from the front of the unit, exhaust 3-way via
rear, left and bottom. Dryer is shipped exhausted to the rear. Alternate
exhausting knockouts are supplied. GAS: An individual, properly-grounded
branch circuit, with a three-prong grounding-type receptacle, protected by a
15- or 20-amp circuit breaker or a time-delay fuse is required. GAS DRYER
ELECTRIC RATING: 120V, 60Hz, 6A GAS (BTU/HR): 22,000. Factory-equipped for
natural gas. Tested for LP gas. LP gas supply requires a conversion kit. Check
installation instructions for correct kit and have a qualified gas technician
install a conversion kit. See dryer ducting information for proper
installation.
NOTE: Dryer wall outlet must be located within 36″ of service cord entry and
accessible when dryer is mounted in position.
INSTALLATION INFORMATION: For complete information, see installation
instructions packed with your dryer.
SPECIAL INSTALLATION REQUIREMENTS
ALCOVE OR CLOSET INSTALLATION:
- If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
- The dryer MUST be exhausted to the outside.
- Minimum clearances between dryer cabinet and adjacent walls or other surfaces are: 0″ either side; 1″ front, top and rear.
- Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
- No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
- The dryer MUST be exhausted to the outdoors.
- The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
M INIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET INSTALLATION:
Minimum clearances to combustible surfaces are: 0″ on both sides; 1″ rear. DRYER EXHAUSTING INFORMATION: Use metal duct only, vertical and horizontal ducting.
Dimension
POWER CORDS:
GE Appliances strongly recommends the use of factory-specified parts. Select
the power cord to fit your installation requirements.*
NOTE: If the dryer circuit is on a circuit protected by a GFCI breaker, then
the 3-wire installation is not permitted. Hose wiring and dryer must be
configured for 4-wire.
For complete information, see the installation instructions packed with your dryer.
DUCTING MATERIALS: For best performance, this dryer should be vented with 4″ diameter all-rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4″ diameter can be maintained throughout the entire length of the transition duct. Please see the installation instructions packed with your dryer for complete instructions when using flexible metal (foil-type) ducting.
EXHAUST LENGTH CALCULATION:
- Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.
- The maximum length of 4″ rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
CAUTION: For personal safety, do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard. Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12″ above the ground or any other obstruction with the opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL 1-800-GE- CARES.
ACCESSORIES
Dryer exhausting information – use metal duct only vertical and horizontal ducting.
For every extra 90° elbow, reduce the allowable vent system length by 10 ft.
Two 45° elbows will be treated like one 90° elbow. For the side exhaust
installations, add one 90° elbow to the chart. When calculating the total vent
system length, you must add all the straight portions and elbows of the system
(including the transition duct).
FEATURES AND BENEFITS
Spanish Control Panel – Dryer controls in Spanish, matching washer (ETW485ASWWB ) sold separately. Auto Dry – AutoDry monitors the internal air temperature to determine the ideal drying time, protecting your garments from overdrying. Powerful Venting & Flexible Installation – Powerful airflow offers long-lasting performance from lint buildup and our venting solutions up to 120 feet for greater installation flexibility Extended Tumble – Tumble clothes without heat to prevent creasing and wrinkling with a convenient extended tumble button. This cycle is ideal to help remove even more pet hair on already-dry items, allowing debris to be caught by your dryer’s lint screen. Interior Light – A convenient dryer drum light provides better visibility to help ensure no small items or socks are left behind, making it easier to load and unload laundry. Adjustable Cycle Signal – The end cycle signal is adjustable and ensures that your garments stay fresh and wrinkle-free with the dryer signal when the dryer is done, allowing you to promptly remove clothes before wrinkles have a chance to form. Large Diuser for Even Drying – A large internal heat diffuser allows warm air to evenly spread throughout your clothes during the cycle, making this the ideal dryer for large loads and bulky items. Durable Aluminized Drum – This durable, long-lasting design resists corrosion and optimizes drying performance. Reversible Dryer Door – The door can swing from either direction, making it easier to access the last sock from the back of the drum. Temperature Selection – Oers a range of drying temperatures to adjust to the specific needs of your garments for personalized garment care. Up-Front Lint Filter – Simplify the task of lint removal with our convenient up-front lint filter, enhancing airflow within the appliance and for your garments. Delicates Cycle – This delicate, low-heat dryer setting helps protect fabrics and extends the lifetime of even your most delicate items. MATCHING WASHER: ETW485ASWWB – GE® 4.5 cu. ft. Capacity Washer with Spanish Panel and Wash Modes Soak and Power
*Order online at GEApplianceparts.com, 24 hours a day or by phone at 877.959.8688 during normal business hours. For answers to your Monogram, Café™, GE Profile™, or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, at 800.626.2000.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>