CLOSETMAID 32801 ShelfTrack With SuperSlide Instruction Manual
- June 2, 2024
- ClosetMaid
Table of Contents
CLOSETMAID 32801 ShelfTrack With SuperSlide
WARNING
- Failure to obey the installation instructions and warnings can result in injury or death.
- Use the correct hardware for the wall type.
- When using standards with hang track, standards must be secured to the wall.
- Do not overload
FOR STUD INSTALLATION
Secure to wall with #12×2 in. pan head screws directly into studs.
FOR CONCRETE INSTALLATION
- Drill 0.25 in. holes and insert #12 wall anchors.
- Secure to wall using #12×2 in. pan head screws.
FOR DRYWALL INSTALLATION
- Drill 0.5 in. holes.
- Remove the toggle from the bolt. Insert bolt-through the hole in standard.
- Re-attach the toggle and insert the toggle into the wall.
- Tighten the bolt to secure it to the wall.
USE THE CORRECT HARDWARE
Select the hardware that is right for your wall type:
Drywall
Drill 1/2 in. holes and secure to the wall with toggle bolts.
Studs
Secure to the wall with #12 x 2 in. pan head screws at stud locations.
Concrete
Drill 1/4 in. holes. insert #12 wall anchors and secure to the wall with #12 x
2 in. pan head screws.
HANG TRACK LOCATION
The track can be installed at any height. However, for maximum adjustability
and the strongest installation, install the track flush to the ceiling and
screw it into the wood header behind the wallboard. Stud installation is
recommended whenever possible for the strongest installation.
DETERMINE LENGTH AND SPACING OF STANDARDS
Standards are available in several lengths, depending on the number of shelves
you want and the spacing between the shelves. The closer the standards are
placed together, the stronger the installation. Standards should be spaced no
more than 24 in. apart, and no more than 4 in. from the end of the shelf.
Choose Your Hardware
- Hang Track
- Standard
- Bracket
- Closet Rod
- Closet Rod Support
- Closet Rod Cap
- Shelf End Cap
SECURING STANDARDS
Each standard must be secured to the wall with one screw at the closest hole
to the centre of the standards. When using toggle bolts, remove the toggle,
put a bolt through the standard and re-attach the toggle to the bolt before
placing standards on track.
ATTACHING BRACKETS
Attach brackets at the desired shelf height.
NOTE: Always match bracket size to shelving depth except when using Shelf
& Rod shelving. Always use 12-inch brackets for this type of shelving. When
installing 16 in. SuperSlide® with Closet Rod & Support always use 12 in.
brackets.
CUTTING SHELVING, CLOSET RODS, AND HANG TRACKS
Wire shelving can be cut using a bolt cutter or hacksaw. Closet rods can be cut using a pipe cutter (recommended) or a hacksaw. Hang tracks can be cut with a hacksaw.
CORNERS
When two shelves come together in a corner, use a corner shelf support to
connect them. Use a corner closet rod to allow clothes to slide uninterrupted
around corners.
Note: SuperSlide® Closet rod supports should be placed where closet rods
join.
END CAPS
Add caps to every exposed wire on both ends of each shelf and the ends of
closet rods. End caps protect you, your clothing and the shelving materials.
ClosetMaid Superslide® shelf system is manufactured by ClosetMaid LLC.,
Orlando, Florida. Manufacturer reserves the right to change specifications
without notice.13485 Veterans Way | Orlando, Florida 32827 |
1-800-874-0008 | US:
closetmaidpro.com,
closetmaid.com | Canada:
closetmaid.ca © 2020 ClosetMaid LLC (01/21)
30 in. Standard
76,2 cm Rail Vertical
76,2 cm Riel Vertical
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>