TeqHome KD-662 GPS Pet Fence System Instruction Manual

TeqHome KD-662 GPS Pet Fence System

Components

WARNING

• Not for aggressive dogs. Do not use this product if your dog is aggressive, or if your dog is prone to aggressive behavior. Aggressive dogs could result in death or serious injury.
• Risk of skin damage. Please read and follow the instruction in this manual. Proper fitness of the collar belt is important.

Product Description

This wireless GPS pet fence system KD-662 uses satellites to accurately locate and define the safe area for your pets. The safe area is up to a circle of 1000 meters radius. If your dog wanders out of the safe area the fence system will automatically start stimulating. And the stimulus will immediately stop once your dog comes back to the safe area.

Main Features

1. Real wireless fence system without any wire and flags layout;
2. Maximum signal range is up to 1000 meters radius with GPS positioning technology;
3. Variety stimulus modes: warning beeper, vibration stimulus and static shock stimulus;
4. Automatically start stimulus once your dog wanders out of the safe area;
5. Flexible and adjustable stimulus intensity from 0 to 3 levels to fit various-size dogs;
6. The GPS fence system is rechargeable with a built-in battery and waterproof;
7. Visual setup operation on LED display;
8. Over-correction protection;
9. Central Point Memory Function

Keys Definitions

Power button:

• Long press : Power on or Power off the fence system
• Short pressure : positioning the central point

M button:

• Long press: set the safe a real distance
• Short press: set and switch the stimulus mode
• Up/Down button: adjust stimulus intensity or adjust safe are a distance
• Contact Point: deliver the static shock stimulus
• Power Jack: charge for the fence system

LED Display

1. Battery Indicator: blank and flashing is low battery alert
2. Beeper mode: warning tone beeper stimulus
3. Vibrate mode :vibraion stimulus
4. Static Shock mode : static shock stimulus
5. GPS Locker: lighted up when sucessfully acquiring the GPS signal
6. GPS Signal Indicator: indicates the GPS signal strength

• Power Saver: flashing on screen after 10 seconds no operation
• Sleeping Mode: flashing on screen after 5 minutes of no  operation

Charging the GPS Fence System
Please fully charge the GPS fence system before using it and it will take about 3 hours. When charging the battery indicator will flash in green colour and stop flashing when fully charged.

Low battery alert: when the battery indicator is blank and fast flashing it means low battery and please recharge it.

Operating Guide

Note: You should fully charge the battery before you use the GPS fence system for the first time. Charging a full battery takes about 3 hours.

Power on/off the GPS Fence System
Hold the power key until the LED displays power on. Hold the power key until the L E D display powers off.

Acquiring the Satellite Signals
The GPS fence system must acquire satellite signals before you put it on your dog. Acquiring satellite signals will take a few minutes.

• Go outdoors to an open area;
• Power on the GPS fence system (as per Step 1 above) and the LED display flash 00;  Now the GPS fence system automatically starts searching the GPS signal and positioning the central point at the current position. It will take about 1 2 minutes
• Once sucessfully searched and positioned the LED display will show the numbers of connected satellites and the GPS Locker on the screen will be lighted up in green; while failure the L E D display will show ER please try again or change another place fo r GPS searching and positioning. shows the GP S signal strength.

NOTICE

1. This GPS fence system is only for outdoor usage and without shelter at the top.
2. The GPS signal will be affected by the buil ding, obstacle, rai ny or cloudy weather and etc.

Set up the Safe Area Distance

Sucessfully acquire the GPS signal and then long press M button to set up the safe area boundary.

• Long press M button;
• Press the Up/Down button to increase and decrease the safe area distance; the distance default starts from 03 levels ( 30 meters);
• The safe area distance setting as follows:

NOTICE

1. The actual distance is 10 times of the value displayed
2. The screen will turn off in 10 seconds once the positioning process is completed. You can press any key to reactive the screen display.
3. To avoid the remote distance is too short and the dogs will be punished unnecessarily, the minimum remote distance is limited to 30 meters.

Set up the Stimulus Mode
There are 3 kinds of stimulus for choice: tone beeper, vibrate stimulus, static shock stimulus. You can choose any one or any combination of them. There are 3 intensity levels for vibration and static shock stimulus except tone beeper.
The stimulus mode and intensity levels as following table:

mode

levels

|

beeper

|

vibrate

|

shock

---|---|---|---
0| deactivate| deactivate| deactivate
1| beeper| low| low
2| X| medium| medium
3| X| high| high

Stimulus settings and operations as follows
The system will automatically start stimulating when your dog go out of the safe area and stop once come back to the safe area.

Note: please test the stimulus function before setting up: press both the Up and Down buttons at the same time the fence system will activate the beeper, vibrate and shock stimulus in turn (you need a test light to test the static shock function). Then you can set up the stimulus mode and intensity as follows:

• Short press the M button switch to beeper stimulus and then you can press Up/Down to choose “1” to activate the beeper stimulus or “0” to deactivate beeper stimulus;
• Short press the M button switch to vibrate the stimulus and then you can press Up/Down to choose “0” deactivate the vibrating stimulus or “1”,”2” or “3” activate the vibrating stimulus;you can choose only one intensity level every time;
• Short press the M button to switch to the static shock stimulus and then you can press Up/Down to choose “0” to deactivate the static shock stimulus or “1”,”2” or “3” to activate the static shock stimulus;you can choose only one intensity level every time;

Over-correction Protection:

• The vibrate or shock stimulus is a duration to 18 seconds every 1 0 seconds which is a stimulus cycle . There are a total 3 stimulus cycles for both vibrate and shock.
• If your dog goes out of the safe area the stimulus will start from vibrate and shock stimulus at the same time (if you activate both vibrate and shock stimulus) wh ile the stimulus will stop after all 3 cycles stimulus even though your dog is still out of the safe is a to avoid overcorrection.
• When you activate the beeper s stimulus there is a 3 cycle limit for it also w which is the same as the vibrate or shock stimulus setting but it will beep during all the 3 cycles

Put on the belt
Put the nylon belt on the fence system and wear it on your dog’s neck with proper tightness.

Important: the proper fitness and placement of the belt is important for effective training. The contact points must direct contact with your dog’s skin.

Important Notes

1. The fence system might not position the central point due to the poor satellite signal. So that, please use this fence system in an open area, which do not have high-rise buildings around it.
2. This product is only for behavioral training of pets such as dogs or cats. Do not use it on human.
3. Please keep this product away from children to avoid their playing causing unintended electric shock.
4. DO NOT leave the collar on your dog for more than 8 hours per day.
5. The fence system has a built-in rechargeable battery. Please fully charge it before using, to avoid any unexpected shutdown or a dissatisfactory result during training.
6. When the device is put on the dog’s neck, please make s ure the tightness is appropriate. Being too loose or too tight will affect the training effect or cause discomfort to the dog.

• The Central Point Memory Function & Re-positioning The collar can memorize the central point after successfully positioning it. The collar will remember it irrespective of whether the collar powers off or runs out of battery.
• Re-positioning the Central Point: A) Short press the Power button by following conditions: satellites are connected successfully and the LED screen is activated; B) if satellites are connected successfully while the LED screen is deactivated then press any key to activate the LED screen and then follow above A) instruction

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>