TeqHome GPCT4117 2 In 1 Wireless Dog Fence And Training Collar User Manual

TeqHome GPCT4117 2 In 1 Wireless Dog Fence And Training Collar User

Manual

Welcome

Thanks for purchasing this Wireless Dog Fence, Please read this user manual carefully before use.
This 2 in 1 Wireless Training System combines the functions of wireless dog fence and remote training collar. Our system adopts the most advanced technology with 2.4G signal source which is much more accurate and stable than any other old versions in the market.

Package Contents(With 1 Receiver Collar) (According To Different

Purchase)

• 1 x Transmitter
• 1 x Receiver
• 1x USB Cable
•  1 x Test Bulb
•  2 x Silicone Caps(Assembled On The Receiver)
•  1 x User Manual

Package Contents(With 2 Receiver Collars) (According To Different

Purchase)

• 1 x Transmitter
• 2 x Receivers
• 1x USB Cable
•  1 x Test Bulb
• 4 x Silicone Caps(Assembled On The Receiver)
• 1 x User Manual

Specificati

• Material: ABS; Woven Strap
• Battery: Transmitter: 3.7V/2000mAh Rechargeable Battery;
• Receiver: 3.7V/400mAh Rechargeable Battery
•  Transmitter Charging Time: 1-2Hrs
• Transmitter Working Tim:
• Receiver Charging Tim
• Receiver Working Time: Depends on Using Frequency (Standby
• Time: 7-10 Days)
• Working Mode: Beep, Vibration, Shoc
• Intensity: 0-9 Levels of Vibration; 0-9 Levels of Shock
• Waterproof Rate: IPX6
• Control Range: 6-260m/20-850ft
• Connecting Quantity: Up To 3 Dogs In Training Mode ; No QuantityLimit In Fence Mode
• Suitable Dogs: 6 Months+; 15-120LBS
• Collar Circumference: 24-58cm/9.45-22.83in
• USB Cable Length: 9.69in
• Receiver Size: 2.56×1.5×1.57in
• Receiver Thickness: 0.98in
• Transmitter Size: 4.33×3.15×0.79in

Friendly Reminder

Please read the instructions carefully before use.

• Please use this device in an open area, the transmitter should beplaced 3.5 feet above ground at least to avoid barriers which willdisturb radio signal.
• Not recommended for aggressive dogs. DO NOT use this device ifyour dog is behaving aggressively.
•  If you are not sure that if this device is right for your dog, please talkto your veterinarian or a certified dog trainer.
•  No more than 12 hours per day to wear the receiver collar.
• If a rash or sore is found, stop using the collar until the skin is healed
• Always keep dog’s neck clean.
•  Keep this device away from children.
•  This device is intended to use for dogs only.
• Short press ON/OFF button to start the device.
• Short press Mode “M” button to switch between Wireless Fence
  Mode and Remote Training Mode:

When the signal symbol on the screen keep flashing, it means thedevice under Wireless Fence Mode

Product Details

1. Controller/Transmitter
2. Receiver
3. Adjustable Reflective Fabric Collar
4. USB Cable
5. Conductive Safe Silicone Cap x 2Pcs (Assembled On The Receiver)
6. ) Static Shock Testing Tool

How Does Wireless Dog Fence Work?

When your dog wears the special collar receiver, and when you set the range by the transmitter, the transmitter will send a radio signal that the receiver can receive.
Your dog will emit a Beep Sound Warning when they approach the preset distance you decide on. As long as your dog continues to approach the preset invisible boundary and passes across the distance you set, the Beep Sound Warning/ Vibration/ Shock mode will be
activated. This encourages your dog to return to the safety zone of your yard

Work ng Principle

Wireless Dog Fence Mode * Under Wireless Fence Mode, you will see 1-16 levels show on the LED screen, which means the setting range is from 20ft. to 850ft., you can adjust the setting level by pressing “+” and ” button, you need to test the desired range in advance.
There is no need to pair between transmitter and receiver.
This mode can work directly after power is on. No limit in the quantity of dogs controlling with 1 transmitter at the same time. 1) Set a range on the transmitter, then put the receiver collar on dog’s neck 2)
When dogs are within the setting range, the receiver colar will not work.
When dogs are out of the setting range, the receiver collar will work as below: <1> Sound for 1 second + Vibration & Shock for 1 second (work simultaneously), indicator light flashing. <2> 2 seconds later, Sound for 1 second + Vibration & Shock for 2 seconds (work simultaneously), indicator light flashing. <3> 2 seconds later again, Sound for 1 second + Vibration & Shock for

Setting Range

1. The signal field on your transmitter represents how far the dog can get around. The higher the number on the transmitter, the wider the distance of the signal field
2. The signal field setting regulates the distance at which the dog’s collar is activated. However it has nothing to do with the correction strength of the collar itself.
3. Under Wireless Fence Mode, you will see 1-16 levels show on the LED screen, which means the setting range is from 20ft to 850ft (may vary due to different environment), you can adjust the setting level by pressing “+” and *-” button, you need to test the desired range in advance.

Friendly Reminder

1. he preset Range(20ft to 850ft) on the transmitter may vary from different environment with various occlusions/signal barriers due to the 2.4G signal. (For example, obstacles like big trees or other signal like WIFI around may affect the effective distance) Sometimes,
   you set it to a second gear of 75ft, it may work at a position of 50t cause the product may be affected by the environment, so you can increase the distance a little bit to a third gear or a fourth gear to find the most suitable preset distance. Therefore, after receiving the
   product, please take your dog walk a few laps after you set the range, find the right distance and gear, and repeatedly train your dog to adapt to the range before wearing the receiver collar.

2. After the transmitter has been tured on, the signal field setting willdiffer. Considering your layout, use the table to choose the signalfield setting that you desire. To adjust the signal field width, use the+and – buttons on your transmitter.

3.  When you successfully set the range by the transmitter, the transmitter will send a radio signal that the receiver can receive. Once the receiver can NOT receive the signal sent by the transmitter, the receiver will emit Beep Sound

Remote Dog Training Mode

• Under Remote Training Mode, signal symbol stop flashing. You can press the CH (channel button) to choose which dog will you train
•  One transmitter can control up to 3 dogs at the same time. ( The transmitter has been paired with receivers by manufacturer, if you need re-pair them, please kindly check the instruction below. )
• The figure shows on the screen indicates that 1 for the first dog, 2 for the second dog, and 3 for the third dog. It can be selected by pressing +” & -” button on the transmitter.

How to P: Manually? Transmitter with Different Receivers

user receives the product since it has been paired by producer. But if you want to pair the receiver to different number(Channel 1/2/3) freely, you can pair the receiver manually.
Please scan the QR code to o see the pairing operation:

1. Turn on both transmitter and receiver.

2.  Under Remote Training Mode (signal symbol stop flashing), press “CH” button to choose dog number.
   Long press “CH” button on transmitter for 3 seconds, until the dog number flashing on the screen.

3.  At this time, long press the power button of receiver and the “CH” button of the transmitter simultaneously and hold. © o

4. When heard “Di” sound from both transmitter and receiver, it means successfully paired!

How to Adjust the intensity

1. Ensure the transmitter and all the receiver collar are power on
2.  Switch to Remote Training Mode (signal symbol & stop flashing)by press the M button
3. Press Shock / Vibration button, adjust the intensity by press *+”

Test In Advance

1.  Static Shock Testing
   Please test the shock function by using the testing tool , put it on the 2metal probes, when electric shock works, the orange light in the toolwill be on. And the stronger the shock mode, the brighter the orange light will be.

2. Receiver Collar Testing

Set a range on the transmitter first, then walk with the receiver collar until it starts with warning sound and red-light flashing, this indicates the receiver collar is within the warning zone. If you move further, the receiver collar will start working mode:

1.  Sound for 1 second + Vibration & Shock for 1 second (worksimultaneously), indicator light flashing
2. 2 second later, Sound for 1 second + Vibration & Shock for 2 seconds(work simultaneously), indicator light flashing
3.  2 second later again, Sound for 1 second + Vibration & Shock for 3seconds (work simultaneously), indicator light flashing
4. To avoid over-stimulation to the dog, vibration & electric shock willnot work anymore after the working cycle, but the warning sound will last 10 minutes until the dog go back to the setting range.

Training Your Dog

To get the most out of your containment system when training, keep these tips in mind:
(1) Verify the system is operating properly and the signal field width is appropriate.
(2) Stay positive and playful during the training session.
(3) Keep training sessions brief. Never continue a session after yourdog has lost interest. Take a break to rest or play.
(4) ALWAYS praise your dog for good behavior.

On-leash Correction

1.  Tum on the transmitter and reset the boundary range before placing the receiver on your dog.
2. Place the receiver and a long leash on your dog.
3. Play with your dog within the containment area for 2-4 minutes.
4. With full control of your dog on a lead/leash, toss a treat on theoutside edge of the flags. As your dog enters the Boundary Zone toreceive the treat, he will begin to receive a beep warning and mildstatic stimulation (B). Allow him to stay in the Boundary Zone for 2
   then gently help your dog back into the Boundary Area (C).Immediately praise and offer him a treat as he enters the Boundary
   Area, even if you have helped with the lead/leash. Wiggle a BoundaryFlag to help your dog understand that the discomfort of the staticstimulation happens around the flags. Repeat the above training several times in different places of youryard

Maintaining Your System

Very little maintenance is required of the collar receivers. Note that the transmitter is not waterproof, and must be mounted in a weatherproof location.

FAQ

Question: Why dose my receiver emit “Di-Di-Di…” all the time?

Answer:First, the receiver may be in low power. Please charge it for about 1-2 hours.
Second, in Wireless Dog Fence Mode, when the transmitter turns off, the receiver will sounds “Di-Di-Di…”. You can turn on the transmitter and press “M” button to switch to Remote
Dog Training Mode, then tumn off the transmitter.(When the receiver can not receive signal, it will sound “Di-Di-Di…”).
Third, in Wireless Dog Fence Mode, the receiver is out of the preset range. When you are back to the range, the sound will stop.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>