McLED Cala LED Wall and Ceiling Luminaires User Manual
- June 2, 2024
- McLED
Table of Contents
McLED Cala LED Wall and Ceiling Luminaires User Manual
Please read the instructions carefully before luminaire installation.
CAUTION:
Turn power off before connecting power supply wires.
Installation and service may only be performed by qualified persons.
Failure to follow these cautions may lead to serious injuries, fire or
luminaire damage.
The luminaire is intended for operation at 230 VAC. Any different voltage may
damage or destroy the luminaire.
The luminaire features degree of protection IP 44. It is also suitable for
damp environment.
The warranty does not apply to luminaire damage resulting from incorrect
installation.
INSTALLATION (Pic. 1-5):
Turn off the power before the luminaire installation.
The power supply wires should be 10-15 cm long.
- In order to remove the plastic cover, it is necessary to turn it counter-clockwise.
- Apply the bottom part of the luminaire to the installation base and mark the mounting holes on the base.
- Drill the holes (Ø 6 mm). Mount the luminaire using dowels and screws included in the packaging.
- Connect the power supply wires to the plastic terminal block on the bottom part of the luminaire.
- Attach the plastic cover by turning it clockwise.
Turn on the power after completing the installation. Check the functioning of the luminaire by switching it on.
MOTION SENSOR ADJUSTMENT AND OPERATION (if included – CALA + sensor):
Recommended height for wall mounting: 1.8-2.0 m Recommended height for ceiling
mounting: 2.5-3 m In case of wall mounting, the sensor detection angle is 150°
(diagram A), for ceiling mounting it is 360° (diagram B).
The sensor is ready to respond precisely to a given situation after setting a
DIP switch combination.
A) Detection zone:
The motion sensor detection zone can be set using DIP switches no. 1 and 2,
see settings in Table A.
| | 1| 2|
---|---|---|---|---
I| ON| ON| 100%
II| ON| –| 75%
III| –| ON| 50%
IV| –| –| 25%
B) Lighting duration setting:
The lighting duration after the motion sensor closing can be set using DIP
switches no. 3, 4 and 5, see settings in Table B.
| | 3| 4| 5|
---|---|---|---|---|---
I| ON| ON| ON| 5 s
II| ON| ON| –| 30 s
III| ON| –| ON| 1 min
IV| ON| –| –| 3 min
V| –| ON| ON| 5 min
VI| –| ON| –| 10 min
VII| –| –| ON| 20 min
VIII| –| –| –| 30 min
C) Day light sensor:
The sensor sensitivity to ambient light can be set using DIP switches no. 6, 7
and 8, see settings in Table C. If the ambient light intensity does not
drop below the values set on the sensor, the luminaire will not turn on in
case of motion detection. If the switches are set to the “deactivated” level,
the luminaire is in the mode of turning on at any motion detection regardless
of the ambient light intensity.
| | 6| 7| 8|
---|---|---|---|---|---
I| ON| ON| ON| 2 lux
II| ON| ON| –| 10 lux
III| –| ON| –| 25 lux
IV| ON| –| –| 50 lux
V| –| –| –| deaktiv.
This product contains a light source in the power saving class (see above).
Exchange possibilities: (1) the light source cannot be exchanged. The
luminaire must be replaced with a new one. (2) the gearbox may be replaced by
a responsible person with corresponding qualifications without permanently
damaging the luminaire.
*McLED® warranty – McLED s.r.o. (Ltd.) provides a three-year warranty on
LED luminaires.
In the event of a claim, the customer is entitled to reimbursement of
reasonable costs incurred in association with the claim only in connection
with shipping costs, which is approved with the seller in advance. To
determine the legitimacy of the claim, the manufacturer must always have the
option of assessing the correctness of the LED luminaire installation on the
site where it is installed.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>