RAIDER RD-PH03 Panel Heater User Manual
- May 15, 2024
- Raider
Table of Contents
Panel heater
USER’S MANUAL
RD-PH03
Structure diagram
A: Display-board
B: Front panel
C: Foot
The pictures are for illustration purpose. The pattern shown may not be
exactly the same as the machine you purchased.
Refer to instruction manual booklet!
Dear Customer,
Congratulations on the purchase of machinery from the fastest growing brand of
electric, gasoline and pneumatic tools – RAIDER. When properly installed and
operating, RAIDER are safe and reliable machines and work with them will
deliver a real pleasure. For your convenience has been built and excellent
service network of 45 service stations across the country.
Before using this machine, please carefully acquainted with these
“instructions’ manual”. In the interest of your safety and to ensure proper
use and read these instructions carefully, including the recommendations and
warnings in them. To avoid unnecessary errors and accidents, it is important
that these instructions will remain available for future reference to all who
will use the machine. If you sell it to a new owner “Instructions’ manual”
must be submitted along with it to enable new users to become familiar with
relevant safety and operating instructions. Euromaster Import Export Ltd. is
an authorized representative of the manufacturer and owner of the trademark
RAIDER. Address: Sofia City 1231, Bulgaria “Lomsko shausse” Blvd. 246, tel 02
934 33 33, 934 10 10, www.raider.bg;
www.euromasterbg.com; e-mail:
info@euromasterbg.com. Since 2006 the company
introduced the system of quality management ISO 9001:2008 with scope of
certification: Trade, import, export and servicing of hobby and professional
electrical, mechanical and pneumatic tools and general hardware. The
certificate was issued by Moody International Certification Ltd, England.
Technical Data
parameter | unit | value |
---|---|---|
Model | – | RD-PH03 |
Voltage | V | 230 |
Frequency | Hz | 50 |
Power | W | 1000-2000 |
Recommend heating area | m² | ≤ 25 |
Introduction
To get the most out of your new heater, please read through these instructions
and the attached safety regulations before use. Please also save the
instruction manual in case you need to remind yourself of the heater’s
functions at a later date.
Important
Before plugging the unit into the mains, ensure by visual inspection that the
unit is intact and has not suffered any damage during transit.
Caution
The appliance must be always placed on a flat and stable surface.
In order to avoid a hazard due to inadvertent resetting of the thermal cutout,
this appliance must not be supplied through an external switching device, such
as a timer, or connected to a circuit that is regularly switched on and off by
the utility.
For your own safety
-
Read all instruction before using the heater.
-
Only connect the heater to a single-phase socket with a mains voltage as specified on the rating plate.
-
Do not leave your home while the appliance is in function: ensure that the switch is in OFF (0) position and the thermostat is in minimum position. Always unplug the appliance.
-
Keep combustible material such as furniture, cushions, bedding, paper, clothes, curtains etc. at least 100cm away from the heater.
-
Do not hand anything on or in front of the heater.
-
Always use the heater in an upright position.
-
Do not place the heater against walls, furniture, curtains, etc.
-
Do not use the appliance in rooms less than 4m² area.
-
Always unplug the heater when not in use. Do not pull the cord to unplug the heater.
-
Keep the air inlet and outlet free from objects at least 1m in front and 50cm behind the heater.
-
Do not install the heater immediately below a socket- outlet.
-
Do not let animals or children touch or play with the heater. Pay attention the air outlet gets hot during operation.
-
Do not cover. If covered, there is the risk of overheating.
-
Do not use this heater in the vicinity of showers, bath tubs, wash basins or a swimming pool etc.
-
Do not use the heater in the rooms containing explosive gas inflammable solvents, varnish or glue.
-
Keep the heater clean. Do not allow any objects to enter any ventilation or exhaust opening as this may cause electric shock, or fire or damage to the heater.
-
If the heater has been dropped or damaged it should not be used until it has been inspected by a qualified service center.
-
Close supervision is necessary when the heater is being used by or near children, persons suffering from any physical impairment or pets.
-
Do not use to dry clothes or any fabric.
-
Do not use the heater to dry your laundry. Never obstruct the intake and outlet grilles (danger of overheating).
-
Do not move the appliance while it is functioning in order to avoid overheating with the additional risk of fire.
-
If any part of the heater or supply cord becomes damaged, it must be replaced by a qualified electrician.
In order to avoid a hazard. -
The heater must not be located immediately below a socket- outlet.
-
Do not use this heater with a programmer, timer or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
-
Do not leave the heater switched on when leaving your home or going to sleep.
-
Children should be supervised to ensure that they do not play with the appliance.
-
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience or knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
-
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
-
Children of less than 3 years should be kept away unless continuously supervised.
-
Children aged from 3 years aтnd less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
-
Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
-
Do not leave unattended when plug in to the mains supply.
Caution
Some parts of the heater can become very hot and cause burns. Do not touch hot
surfaces.
Particular attention has to be given where children and vulnerable people are
present.
Note
These heaters are intended for domestic use only. They can be used as both
portable appliance and wall mounting appliance.
Product features
- Elegant black glass panel.
- High quality aluminum heating element: quick heating with higher energy savings.
- Touch screen control and remote control.
- Digital display with automatic room temperature display.
- For wall mounting or free standing with base.
- Remote control can be available.
Installation (While use on the floor as portable appliance)
Please attach the feet on the heater’s housing, and fixing them with supplied
ST4x12mm(8pcs) screws.
Wall mounting (While use the heater as fixed appliance)
Please note that the product must be installed at least 15 cm from the floor
and 50 cm from the ceiling.
– For wall mounting study scheme
- Uninstall the bracket from the body, see the image.
- Drill the holes at each sides on the wall, then insert the plastic expanded plugs within, Fix the bracket in the wall with screw, see the image 2
- Fit the heater into suitable position ensuing that the holes align with bracket. See image 3
- Tight the screw on the top of bracket to catch steady
Operation
Insert the plug into a suitable socket outlet on an A.C. power supply having
the same voltage as that shown on its rating label.
The touch screen buttons located on the product correspond to the remote
control functions:
- Display
- Receiver
- Minutes button
- Mode button
- Setting button
- Heating button
- Temperature “+“ button
- Temperature “-“ button
Standby Mode
Before you working the heater,your should turn on the switch in side. The
display shows as image 1, it’s standby mode, no heating, shows in the screen.
Long press button to set hours, long press button to set minutes, long press ,
to set day, see image 1.
Work Mode
Press to change the mode from standby mode to work mode, the display shows as
below image 2, shows in the screen. Press button to regulate high heat
setting and low heat setting, it’s low heat setting when shows in the screen,
it’s high setting when shows in the screen, see image 2. Press or button to
select the desired temperature from a range of 5°-40°C. the temperature shows
in 2 sets numbers, the left number shows current temperature, the right number
shows setting temperature, see image 3.
Weekly timer Mode
Press to change the mode from standby mode to work mode, the display shows
as below image 5, shows in the screen. Press button to select between the
following pre-programmed heating periods as follows,see image
- Monday to Friday
- Monday to Saturday
- Every day
- Monday, Wednsday, Friday
- Tuesday, Thursday, Saturday
- Weekend
- Monday to Wednsday
- Thursday to Saturday
- All normal open.
Press button to set the the start time, press button to set the stop time. For example, press button to 9:00, it means from 0:00 to 9:00, the heater keep working, then press button to set the stop time, if set 12:00, it will stop on 12:00, and then press and again until 24 hours all was setting finish, it will show current time when the setting is finish, see image 7.
Child clock
Long press botton, will be display on the screen, so you can not make any
operation ,and same way to touch to delete the child clock function.
Remote control and control panel:
- “SET” P, W, S three modes to choose and set current week.
- “MODE” Reserve week.
- “ ” Set child lock.
- “ ” Adjust the power.
- “ ” Set open appointment time and increase temperature.
- “ ” Set close appointment time and decrease temperature.
Temperature
Internal temperature is displayed every time the appliance is started up. The
temperature can be set when the appliance is in stand-by or heating. When the
room temperature reaches the set level, the high temperature power stops and
the low temperature power remains active. When room temperature is 2 degrees
over the set temperature, both the high and lower temperature powers will stop
operating. The machine will begin operating again only when temperature
decreases 2 degrees with respect to the set temperature. The error of display
temperature and real room temperature ≤ 4 degree.
Operating sound
The appliance emits a beep upon each operation setting.
Cleaning and maintenance
Before cleaning always remove the plug from the electrical socket outlet.
Clean the air inlet and outlet grilles frequently.
Never use abrasive powders or solvents.
Disposal Information
Should you want to dispose of this item please do not put it with the
household waste. Used electrical and electronic equipment and batteries must
be made available for separate collection.
Private households may return their used electrical and electronic equipment
to designated collection facilities free of charge. Identify where your local
collection points are and return the product there. (Facilities are usually
available at the municipal waste site. your electrical retailer, or your local
authority may provide separate collection from the household.)
By disposing of this product correctly you will be providing positive help to
the environment.
Environmental protection. In order to protect the environment, the power tool,
accessories and packaging must undergo appropriate processing for the reuse of
the raw materials contained in them. Do not dispose of power tools with
household waste! According to the EU Directive 2012/19/EC on end-of-life
electrical and electronic equipment and the approval and as a national law,
power tools that can no longer be used must be collected separately and
subjected to appropriate processing to recover the contents are in them
secondary raw materials.
DECLARATION OF CONFORMITY Panel Heater RD-PH03
Euromaster Import Export Ltd. Address: Sofia 1231, Bulgaria, 246 Lomsko
shausse Blvd.
We declare under our sole responsibility that this product is in conformity
and accordance with the following standards and regulations:
EN 55014-1:2017
EN 55014-2:2015
EN IEC 61000-3-2:2019| EN 62233:2008
EN 60335-2-30:2009+A11:2012
EN 61000-3-3:2013+A1+2019
---|---
EN 60335-1:2012+AC:2014+A11:2014+A13:2017+A1:2019+A2:2019+A14:2019
EC DECLARATION OF CONFORMITY
Euromaster Import Export Ltd.
Address: Sofia 1231, Bulgaria, 246 Lomsko shausse Blvd.
Product: Panel Heater
Trademark: RAIDER
Model: RD-PH03
s designed and manufactured in conformity with following Directives:
2014/30/EU of the Еuropean parliament and of the council of 26 February 2014
on the harmonisation of the laws of the Member States relating to
electromagnetic compatibility;
2014/35/EU of the European Parliament and of the Council of 26 February 2014
on the harmonization of the laws of the Member States relating to the making
available on the market of electrical equipment designed for use within
certain voltage limits; and fulfils requirements of the following standards:
EN 55014-1:2017
EN 55014-2:2015
EN IEC 61000-3-2:2019| EN 62233:2008
EN 60335-2-30:2009+A11:2012
EN 61000-3-3:2013+A1+2019
---|---
EN 60335-1:2012+AC:2014+A11:2014+A13:2017+A1:2019+A2:2019+A14:2019
www.raider.bg
EUROMASTER IMPORT EXPORT LTD
1231, Sofia, Bulgaria, 246 Lomsko shose Blvd.,
tel.: +359 700 44 155
fax: + 359 2 934 00 90
www.euromasterbg.com; e-mail:
info@euromasterbg.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>