nathan james 34108 Jackson Floating Side Table Installation Guide
- May 15, 2024
- NATHAN JAMES
Table of Contents
34108 Jackson Floating Side Table
Installation Guide
Jackson Floating Side Table
Let’s build the
SKU 34108
34108 Jackson Floating Side Table
Scan me!
Free Lifetime Warranty
Ok, lets get rolling
This should be easy, just follow our instructions and you will be back to
Netflix in no time.
Estimated time for assembly
What you need
- Some of your favourite bubbly or your preferred relaxant
- Use the packaging carton as a working surface to prevent product damage during assembly
- Phillips head screwdriver
- Drill
- 1/4” Drill Bit OR 5/16” Drill Bit
Weight Limitation
What’s included
| Description| Qty
---|---|---
1| Top Panel| 1
2| Left Side Panel| 1
3| Right Side Panel| 1
4| Bottom Panel| 1
5| Back Stretcher| 1
6| Back Panel| 1
7| French Cleat for Cabinet| 2
8| French Cleat for Wall| 2
9| Drawer Front| 1
10| Drawer Left Side| 1
11| Drawer Right Side| 1
12| Drawer Back| 1
13| Drawer Bottom| 1
Scan me!
Free Lifetime Warranty
The goods
IMPORTANT
- Do not tighten bolts / screws completely until all bolts / screws are lined up and inserted into holes.
- Please use hand tools for assembly. Do not over tighten screws and bolts to avoid stripping.
What’s included
| Description| Qty
---|---|---
A| M635mm Cam Bolt| 18
B| 159.5mm Cam Lock| 18
C| M630mm Wooden Dowel| 12
D| M430mm Screw| 8
E| M312mm Screw| 8
F| Left Side Panel Slider (CL)| 1
F| Right Side Panel Slider (CR)| 1
F| Right Side Drawer Slider (DR)| 1
F| Left Side Drawer Slider (DL)| 1
G| M450mm Screw (for Non-Drywall Anchor)| 4
H| M630mm Anchor for Non-Drywall| 4
I| Drywall Anchor| 4
J| M470mm Screw (for Drywall Anchor)| 4
K| PVC Sticker| 4
L| Mounting Installation Template| 1
M| M4*16mm Screw (for Handle)| 1
N| Handle| 1
The goods
Step 1
Let’s get this thing fired up! Lay down the packaging carton or use carpet
as a working surface.
To start, screw the M635mm Cam Bolts (A) into the Top Panel (1), Left Side
Panel (2), Right Side Panel (3), and Drawer Front (9).
Step 2
Attach the Drawer Left Side (10) and Drawer Right Side (11) to the Drawer
Back (12) using the M430mm Screws (D).
Step 3
To finish up the drawer, slide in the Drawer Bottom (13). Then attach the
Drawer Front (9) using the 159.5mm Cam Locks (B) to secure in place. Finally,
attach the Handle (N) using the M416mm Screw (M).
See the following page for instructions on how to use cam locks.
How to use cam locks
Did you know?
Cam locks are used to join two panels together, usually the edge of one to the
flat side of another.
First, your cam bolt (or cam pin) will need to be properly inserted into the
flat side of the board. Important Note: Only tighten the cam bolt until it is
secure. Do not over-tighten.
Next, you will fit the proper hole on the edge of the associated joining panel
over the cam bolt. Important Note: When installed properly, the head of the
cam bolt will be visible through the larger hole on the side of the joining
panel.
Next, you will notice the cam lock has a “C” shaped back. Commonly, an arrow
on the front of the cam lock points in the same direction as the open section
on back.
Using these as your cue, insert the cam lock into the large hole so the
opening of the “C” fits over the head of the cam bolt.
Using a screwdriver, you will turn the cam lock until it stops, usually
between 1302 or 1802. You will feel the panels pulling closer until they are
secured. 
Important Note: Only turn the cam
lock until the panels are fully engaged & feel secure.
Turning too far may lead to hardware failure.
If a. cam lock seems to be spinning in place or is not “catching” or pulling
the panels together as expected, first remove the cam lock & try again while
making sure that everything is properly positioned & oriented .
Sail having Sie lotrg If you are still having issues getting things work
ing as expected, first remove the cam lock then unscrew the cam bolt slightly
(less than 1 complete turn) to see if that helps with the alignment of the cam
lock & bolt
Step 4 Get those Drawer Sliders (F) out and let’s finish this drawer!
Using the M312mm Screws (E) and the diagram below, align the DL and DR Drawer
Sliders and secure in place.
Step 5
We know this graphic looks intense, but trust us, it’s easy! Secure the
Left Side Panel Slider (F)(CL) and Right Side Panel Slider (F)(CR) to Left
Side Panel (2) and Right Side Panel (3) using the M312mm Screws (E). Finally,
add Wooden Dowels (C) to both Panels (2)(3).
Step 6
Next, insert Wooden Dowels (C) into the sides of the Back Stretcher (5).
Then secure the Back Stretcher (5) to the Right Side Panel (3) and use the Cam
Lock (B) to secure in place.
Step 7
Take the cabinet you’ve built so far from Step 6 and attach the Bottom Panel
(4) using the Wooden Dowels (C). Once in place, secure using the Cam Locks
(B), then place a PVC Sticker (K) over the top of the Cam Locks if you don’t
want them to be visible.
Step 8 Attach the Left Side Panel
(2) by repeating the process from Step 7, and continue placing the PVC
Stickers (K) over the Cam Locks (B).
Step 9 You’re doing so well! So we decided to make this step super easy for you. Just slide in the Back Panel (6).
Step 10 Now attach the Top Panel
(1) by aligning the holes in the Top Panel with the Wooden Dowels already
placed in the cabinet sides in previous steps. Once in place, secure using the
Cam Locks (B).
Step 11 Now turn around the
cabinet and secure the French Cleat (7) pieces by lining up the Cam Bolts (A).
Once in place, secure using the Cam Locks (B).
Step 12 Now reach into the back
of the panel and secure the Back Stretcher (5) using the M4*30mm Screws (D).
Step 13: Using the Mounting Installation Template
Unroll it
Unroll the paper Mounting Installation
Template (L) and remove the adhesive backing at the corners.
Place it
Locate where you would like to mount the side table and apply the Mounting
Installation Template (L) to the wall in that location. Make sure the template
and holes are level.
Mark it
Using the holes in the template and the metal rail as a guide, mark the
location of each hole on the wall. These will become your guides as to where
to drill the holes for the wall anchors.
Remove it
Slowly remove the paper, ensuring that all holes have been marked.
Drill it
Drill each hole to the suggested size.
Important Note: Non-drywall = 1/4” drill bit Drywall = 5/16” drill bit
Step 14: Non-drywall
After using the Mounting Installation Template (L) to mark and pre-drill
holes into your wall, press the Non Drywall Anchors (H) into the drilled
holes.
After the anchors are in place, secure the French Cleat for Wall (8) to the
wall by inserting and tightening the M4*50mm Screws (G) through the Cleats and
into the anchors.
See the next page (page 19)for more detailed instructions. If you’re mounting
your tableon to drywall, skip ahead to page 20 for instructions.
1/4” Drill bit
Following the marks you just made, with a 1/4” drill bit, drill 4 holes into
the wall.
Insert the anchors
Go ahead and tap the wall anchors into place in the new holes that you just
drilled. If you’re feeling strong, just go ahead and push it in.
Step 14: Drywall
After using the Mounting Installation Template (L) to mark and pre-drill
holes into your wall, press the Drywall Anchors (I) into the drilled holes.
After the anchors are in place, secure the French Cleat for Wall (8) to the
wall by inserting and tightening the M4*70mm Screws ( J) through the Cleats
and into the anchors.
See the next page (page 21) for more detailed instructions. If you’re mounting
your table onto non-drywall, skip back to page 18 for instructions.
5/16” Drill bit
Following the marks you just made, with a 5/16” drill bit, drill 4 holes into
the wall.
Insert the anchors
Go ahead and tap the wall anchors into place in the new holes that you just
drilled.
If you’re feeling strong, just go ahead and push it in.
Step 14: How to Use Drywall Anchors
Step 15 Now that the wall is prepped, line up the French Cleat for the Cabinet with the French Cleat for the Wall and set your floating side table on the wall.
Step 16 Before you start placing your chips and salsa on the tabletop,
please finish securing the table to the wall using the M4*30mm Screws (D).
Step 17 You made it to the last step! We’re super proud of you, and that
table is looking great!
Now line up the drawer sliders and carefully push your drawer in. Okay, now
your can place your chips and salsa on top!
Give us a call
1-866-619-1004 or shoot us a message at
help@nathanjames.com we will issue you a free
replacement with zero hassle.
No heartburn, when we handle the return
| Our way | Their way |
|---|---|
| Give us a call | Re-package item |
| Replacement | Schedule pick up |
| You | Track package |
| Replacement | |
| You |
We really don’t want you to go through the hassle of repackaging your item and sending it back, because let’s be honest…nobody has time for that.
Safety first, fun later
We want your product to last as long as possible, so we recommend that you
tighten the screws 2 weeks after assembly and for added safety check the
tightness of all screws every 2 months.
For proper care and treatment, please check our website at
NathanJames.com/products
Safe use of this product starts with you.
Use this product responsibly with the primary concern for your safety. Follow
assembly instructions carefully and inspect product upon receipt and each use.
Nathan James and its parent companies cannot be held legally responsible for
any injuries or death resulted from failure to follow instructions or improper
use of this product.
Do not modify the structure of this product in any way.
Our products have been tested to meet specific safety measures as they were
originally intended to be sold. Any modifications will present the risk of
creating significant safety issues which NJ will not be responsible for.
Proper use
| DO NOT | use for commercial purposes |
|---|---|
| DO NOT | frolic on table |
| DO NOT | use table as stool |
| DO NOT | leave spilled liquid on table |
| DO NOT | use table if damaged |
| DO NOT | make temporary repairs |
| DO NOT | use outdoors |
We are only in business if you’re happy
For starters, thanks for being you.
Toll-free at 1-866-619-1004
Help@nathanjames.com
NathanJames.com/help
We do our best to ensure your furniture arrives without any problems, but
occasionally mistakes happen—as humans we are imperfect beings. In the event
that a part is damaged or missing, we will be more than happy to provide you
with replacement part(s) for free.
Warranty
This product comes with a lifetime warranty from the date of purchase. Please
use your phone to scan the QR code to register your product or visit
https://goo.gl/i9dk3q
Did we do alright? Please spread the love!
If you are happy with your product, tell your friends and family about us or
even better leave us a review online. Spreading the word gives us the
opportunity to make more people happy and keep our prices low for your next
purchase.
B rooklyn B urdon
Founder, Nathan James
Documents / Resources
|
nathan james 34108 Jackson Floating Side
Table
[pdf] Installation Guide
34108, 34108 Jackson Floating Side Table, Jackson Floating Side Table,
Floating Side Table, Side Table, Table
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>